DAITEM 171-21X User manual

2
2. Preparation
2.1 Opening 2.2 Power supply
Open the detector casing by loosening
the screws using a cross-head
screwdriver.
Connect the lithium battery pack according to the arrow.
Test button
Test LED
indicator
la p behind
lens
Detection
lens
Locking screw
The infrared detector is used for protection inside buildings. Intruders are detected when the infrared radiation associated
with movement varies. The detector also detects freezing temperatures based on a thermostatic principle (a technical alarm
is triggered when the temperature drops below 5°C).
1. Introduction
0 2 4 6 8 10 12
2,2m
16 18 20 22
14
1
0 1 2 3 4 5 6 7 8 9 10 11 12
2,2m
1
0 5 10 15
2
2
0 5 10 15 20 22
1
1
0123456 7 8 9 10 11 12
1
2 m
• 171-21X/175-21X: motion detector
(19 fields-of-view, 12 m, 90°) is
designed to protect rooms at risk
(lounge, main bedroom, etc.).
• 172-21X: corridor detector (9 fields-
of-view, 22 m, 12°) is designed for
unavoidable passageways, and can
be placed facing the entry point to
be protected.
• 173-21X: curtain detector (9 fields-
of-view, 12 m, 8°) is designed for the
protection of large surfaces (plate
glass windows, garage doors, etc.).
0 2 4 6 8 10 12 m
2,20
12 m
48
0
detection zone
(1st interruption)
detection zone
(2nd interruption)
Align ent arrow
Re ovable tab
Guarantee sticker
Remove the pre-cut part of the sticker
and stick it to the guarantee certificate in
the user manual supplied with the control
panel. If you are adding the siren to an
existing system, use the guarantee
sticker provided with this product.
171-21X
171-21X

3
3. Programming
IM ORTANT: during recognition programming, the product to be programmed for use with the control panel does not need to
be placed next to it. In fact, we recommend you place the product at a short distance from the control panel (at least 2 meters
away).
Programming enables the detector to be recognised by the control panel.
2. Programme the device as follows:
1. To programme the detector the control panel must be in installation mode. If it is not, ask the user to press:
then
“beep, installation
ode”
IM ORTANT: the control panel indicates there is an error by emitting 3 short beeps. When this happens programming
should be carried out again.
Press *then #on
the control panel
keypad
Press and hold the “test”
button until the control
panel responds
The control panel waits
for a group to be chosen
(from 1 to 8)*. Choose the
group by pressing the
corresponding numeral on the
control panel keypad
Choose the type of triggering:
0: immediate
1: delayed
2: combined
Use the control panel keypad
to select the type
The control panel
gives a voice
message to confirm
then to
)))))
10 s max.
“detector X” “group?” “ti e delay?”
*to
* according to the
type of control panel
master code
(0000 by default)
engineer installer code
(1111 by default)
“beep, detector X,
group Y i ediate
(or delayed
or co bined)”
• Example: programming of 1st detector allocated to Gr. 2 with immediate triggering.
“beep, detector
1, group 2,
i ediate”
)))))
10 s max.
“detector 1” “group?” “ti e delay?”
then
IM ORTANT: the control panel indicates
there is an error by emitting 3 short
beeps. When this happens programming
should be carried out again.

4
Checking configuration: check the alarm level by selecting the Parameter N° and checking the number of corresponding
flashes.
Start Press 4 times to select
the alar level
Press once to
accept selection
End 2 flashes confir
that the device is set
for a prealert
4 2
4. Configuration
IM ORTANT: The casing must be open when configuring the detector.
• Detection parameter selection:
• Follow the configuration sequence described below:
Choice arameter arameter Technical data
of function n° value
Detection sensitivity 1 1 1st edge triggering: not recommended for detector 171-21X/175-21X
2 2nd edge triggering (factory setting):
recommended for interior using detector 171-21X/175-21X
Alarm level 4 1 Intrusion (factory setting)
2 Prealert
3 Deterrence
4 Warning
Freeze detection 7 1 Disabled (factory setting)
setting 3 Enabled
Configuration example: setting the detector for an alarm level when a full prealert is triggered: Parameter n° 4, Parameter
value 2.
To start the sequence
press and hold the
button until the LED
indicator la p goes out
Press 1, 4 or 7 times
depending on the
required para eter
nu ber
ress and hold
until the LED
indicator la p
briefly goes out
Press 1 to 4 times
depending on the
required para eter
value
To end the sequence
press and hold the button
until the LED indicator
la p goes out
1, 4 or 7 1 to 4
about
5 sec. about 10 sec. about 2 sec.about 10 sec.
LED indicator
la p lit =
correct
configuration
Start Press 4 times to select
the alar level
Press once to
accept selection
Press 2 times
to select
the prealert level
Press and hold until the
LED goes out to finish
4 2

5
5. Installing the detector
5.1 Choosing the best place
IM ORTANT: make sure there is a distance of at least 2 meters between each product, except between two detectors.
The motion detector must be placed:
• inside the building,
• 2.20 m above ground level
• at right angles to the entrances to be protected (interior
detection works best when the intruder walks across the
detector’s fields-of-view),
• directed towards the inside of the room to be protected,
• in such a way that the area it protects does not overlap
with that of another motion detector.
The motion detector must not be placed:
• in an area likely to receive direct sunlight or a very powerful
light source,
• opposite or above a source of heat,
• outside or in a breezy place,
• directly on to a metal wall or close to sources of
interference (electricity meters, etc.) or ventilation such as
air-conditioning grilles.
5.2 Fixing method
IM ORTANT: for reasons of security and to ensure long battery life, installation of the anti-tamper pin is compulsory. In case of
omission or incorrect insertion of the pin, the detector LED indicator lamp flashes continuously when the detector is fitted to its
bracket.
The detector can be fixed to a wall
in 3 ways:
• on a swivel bracket,
• flat against the wall,
• in a corner.
There is an anti-tamper pin for each
type of fixing method:
• swivel bracket: pin n° 0,
• flat: pin n° 1,
• in a corner: n° 2.
RIGHT
WRONG
RIGHT
WRONG
Back plate cover
Order in which to assemble parts
Selection of pins
Screw
+ tightening
washer
Swivel
ong screw
Pin n° 1
Pin n° 2
Back plate
Base
Pin n° 0
for swivel bracket
fixing (factory-
mounted pin)
Pictogram
Pozidriv 1
Pozidriv 2
IM ORTANT: for swivel bracket fixing, pin n° 0 is already factory-positioned inside the detector.
• Fixing the detector on a swivel bracket
1. Hold the back plate against the wall in the desired position and
mark where to drill the holes.
2. Drill the holes in the wall.
3. Insert the long screw via the back plate and fasten the plate to the
wall.
4. Put the back plate cover in place.
5. Assemble both parts of the swivel.
6. Insert the mounted swivel into the long screw.
7. Position the base of the motion detector (a picture of a man shows
the top of the detector).
8. Tighten the screws lightly in order to be able to adjust the direction
of the motion detector.
9. Place the motion detector on its base and turn it so that it is facing
the right way.

6
5.3 Directing and testing the detector
IM ORTANT: the control panel must be in installation mode to check the above.
IM ORTANT: at the end of the test period, the detector automatically switches back to normal operating mode:
• detector inhibited for 90 sec. after detection,
• the test LED indicator lamp is no longer lit when movement is detected.
The infrared detector has a test mode for
checking:
• the power supply: the ED indicator lamp
lights up when you press the test button to
confirm the battery is operating correctly,
• the detection area: the ED indicator lamp
lights up on detection,
• the radio link (see § on checking the radio
link in the control panel manual).
)))))
Checking the detection area:
• press on the test button: the detector switches to test mode for a period
of 90 sec.,
• walk across the detection area at right angles to the detector’s fields-of-
view (see diagram): every time movement is detected the detector test
ED indicator lamp lights up.
If no movement is detected: change the way the detector is facing on its
swivel bracket, check there is no obstacle between the detection area and
the detector.
“beep, detector X,
group Y i ediate
(or delayed
or co bined)”
Pozidriv 1
Pozidriv 1
IM ORTANT: when fixing the movement detector at an angle or flat against the
wall, fix the label (provided in the sachet of accessories) on the reverse side of the
product in order to cover the opening to avoid insects getting through.
Si fixation en angle ou à plat contre un mur
For a fixing in a corner or flat against the wall
Si fixation en angle ou à plat contre un mur
For a fixing in a corner or flat against the wall
1
653563_A
2
• Fixing the detector flat against the wall
1. Drill through the two pre-drilling holes in the base of the motion detector.
2. Place the base against the wall in the desired place in order to mark
where to drill the holes (a picture of a man indicates the top of the base).
3. Drill the holes in the wall and fix the base.
4. Remove the factory-positioned pin.
5. Detach pin n° 1 from the selection supplied.
6. Position the pin in the right place.
7. Place the motion detector on its base.
• Fixing the detector in a corner
1. Drill through the two pre-drilling holes in the base of the detector.
2. Place the base against the wall in the desired place in order to mark
where to drill the holes (a picture of a man indicates the top of the base).
3. Drill the holes in the wall and fix the base.
4. Remove the factory-positioned pin.
5. Detach pin n° 2 from the selection supplied.
6. Position the pin in the right place.
7. Place the motion detector on its base.
2 fixing
screws
Pre-drilled holes
Pictogram
Pictogram
2 fixing
screws
Pre-drilled holes
90°
Pin n° 2 for fixing
the detector
in a corner
171-21X
175-21X
172-21X
173-21X
Pin n° 1 for fixing
the detector flat
against the wall

7
6. Maintenance
6.1 Battery low indication
6.2 Changing the battery
IM ORTANT: if the test LED indicator lamp no longer lights up, the lithium battery should be replaced.
The control panel indicates when the infrared detector’s battery is low.
To check whether there is a problem with the detector battery, press on the detector’s test button.
To change the battery:
1. Switch the control panel to installation mode and ask the user to press:
then
The detector’s configuration is saved when the battery is changed.
2. Open the detector casing (see § on Opening).
3. Unclip the lithium battery pack.
4. Wait 2 min. before replacing the flat lithium battery.
5. Close the detector.
6. Switch the control panel back to user mode. Press:
“beep, installation
ode”
“beep, date,
ti e, off”
master code engineer installer code
engineer installer code
IM ORTANT: ull on the tab to remove the lithium battery.
7. Technical data
Specifications Infrared motion detector
Infrared detection • 171-21X/175-21X: 12 m, 90°, motion detector
• 172-21X: 22 m, 12°, corridor detector
• 173-21X: 12 m, 8°, curtain detector
Fixing methods • on a swivel bracket
• flat against the wall
• in a corner
Use inside
Power supply 2 x 3.6 V - 2 Ah Bat i25 lithium battery
Battery life 5 years in normal conditions of use
Average humidity rate 5% to 75% without condensation at 25°C
Radio links TwinBand®400/800 MHz
Test button battery and detection
ED indicator lamp 1
Operating temperature -10° C to +55° C
Protection mechanism against opening and removal (unless swivel bracket mounted)
Degrees of mechanical protection IP 31/ IK 04
Dimensions without swivel bracket 58 x 102 x 57 mm
Weight 115 g (with battery, swivel bracket and base)
• The lithium battery pack must be replaced by the same type of pack with the same technical characteristics
(BATLi25, 2 x 3.6 V – 2 Ah).
• We advise you to use the DAITEM BatLi25 pack available in the catalogue in order to guarantee individual
safety and equipment reliability.
• Dispose of the waste lithium power pack in an appropriate recycling bin.
Li

805153/A - 10.2012
Non-binding document, subject to modification without notice.
DECLARATION OF CONFORMITY
Manufacturer: Hager ecurity A
Address: F-38926 Crolles Cedex - France
Product type: Motion detector
Trade mark: Daitem
We declare under our sole respons b l ty that the products to wh ch th s declarat on relates
are thus compl ant w th the essent al requ rements of the follow ng European D rect ves:
• R&TTE Directive: 99/5/CE
• Low Voltage Directive: 2006/95/CE
• ROH Directive: 2002/95/CE
n compl ance w th the follow ng harmon sed European Standards:
These products can be used n all EU, EEA Countr es and Sw tzerland.
Crolles, 31.08.2012 S gnature:
Patr ck Bernard
Research & Development Manager
12
GB
Products code 171-21X 172-21X 173-21X 175-21X
EN 300 220-2 V2.1.2 X X X X
EN 300 330-2 V1.3.1
EN 50130-4 (95) + A1 (98) + A2 (2002)
X X X X
EN 55022 & 55024 (2002)
EN 60950 (2006) X X X X
EN 301 489-1 V1.8.1 X X X X