dallmeier RDF6000DN Series User manual

Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.2.0 2022.03.07 1/7
▶ Carefully remove the three
rubber covers from the screws.
Preparing the camera
▶ Remove the camera’s housing
cover by turning and lifting it.
▶ Open the three screws of the
cover ring counterclockwise
using an Allen key.
ca. 10°

Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.2.0 2022.03.07 2/7
▶ Carefully lift the rubber seal
out of the camera housing
using a small screwdriver.
▶ Then remove the cover ring
including the dome from
the camera.
▶ Insert the board into the board
opening and press it carefully
with light pressure.

Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.2.0 2022.03.07 3/7
▶ Insert the new gasket into the
board slot and press it rmly until
it is even with the surface.
▶ Insert the screws and tighten
them with an Allen key.
Installing the Dual Matrix LED Ring
▶ Place the Dual Matrix LED Ring
on the camera. Make sure that
the connector snaps into the
socket of the board.

Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.2.0 2022.03.07 4/7
▶ Gently press the LED ring into place.
▶ Insert the three screws into the
LED ring and tighten them.
▶ Place the cover ring with the dome
on the LED ring of the camera. Pay
attention to the alignment of the
three bracket screws.

Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.2.0 2022.03.07 5/7
▶ Carefully remove the protective
foil over the ve LED viewing
windows using tweezers.
▶ Then tighten the screws clockwise
using the Allen key.
▶ Use the tweezers to remove
the foil over the microphone.

Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.2.0 2022.03.07 6/7
▶ Use a small screwdriver to
remove the two red covers
for the fastening screws.
▶ Reinsert the rubber covers
over the three screws.
Installing the aluminum ring
▶ Mount the safety strap on the
camera and on the housing cover.

Dallmeier electronic GmbH & Co.KG | Bahnhofstr. 16, 93047 Regensburg, Germany | [phone] | dallmeier.com
All trademarks identified by ® are registered trademarks of Dallmeier electronic GmbH & Co.KG.
Third-party trademarks are named for information purposes only. Dallmeier electronic respects the intellectual property of third parties and always attempts to ensure the complete identification of third-party
trademarks and indication of the respective holder of rights. In case that protected rights are not indicated separately, this circumstance is no reason to assume that the respective trademark is unprotected.
Specifications subject to change without notice. Errors and misprints excepted. Pictures may dier from the actual product.
© 2022 Dallmeier electronic V1.2.0 2022.03.07 7/7
Installation camera series RDF6000DN
INSTALLATION AND CONNECTION OF A DOMERA® DUAL MATRIX LED RING
INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
▶ Place the aluminum ring on
the camera. Pay attention to
the positioning of the two
bracket screws.
▶ Tighten the two screws clockwise
using an Allen key.
▶ The installation is complete and
the camera can now be mounted.