dallmeier DDF3000AV4-DN Operating and maintenance instructions

1
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
Rev. 1.0.0 / 090703
English
Installation and Configuration
DualMode colour dome camera (Day/Night), vandal-resistant
DDF3000AV4-DN
DDF3000AV4-D
Surface mount version In-ceiling mount version

2
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
Information about copyright, trademarks, design patents
© 2009 Dallmeier electronic
All rights reserved. This document may not be copied, photocopied, reproduced, translated,
transferred to an electronic medium or converted to a machine-readable form either whole or in
part without rst receiving written permission from Dallmeier electronic GmbH & Co.KG.
We reserve the right to make technical modications.
The manufacturer accepts no liability for damage to property or pecuniary damages arising due
to minor defects of the product or documentation, e.g. print or spelling errors, and for those not
caused by intention or gross negligence of the manufacturer.
Dallmeier electronic GmbH & Co.KG
Cranachweg 1
D 93051 Regensburg, Germany
www.dallmeier.com
[e-mail]
All trademarks identied by ®are registered trademarks of Dallmeier electronic.
All trademarks identied by *) are trademarks or registered trademarks of the following owners:
Digital Pixel System of Pixim, Inc. headquartered in Mountain View, California, USA
Third-party trademarks are named for information purposes only.
Dallmeier electronic respects the intellectual property of third parties and always attempts to ensure the complete identication of
third-party trademarks and indication of the respective holder of rights. In case that protected rights are not indicated separately, this
circumstance is no reason to assume that the respective trademark is unprotected.

3
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
Table of contents
1 About this document����������������������������������������������������������������������������������������������5
1.1 Validity ......................................................................................................................5
1.2 Documents................................................................................................................5
1.3 Conventions..............................................................................................................5
2 Safety instructions �������������������������������������������������������������������������������������������������7
3 General notes����������������������������������������������������������������������������������������������������������9
3.1 Scope of delivery ......................................................................................................9
3.2 Transportation and packaging ..................................................................................9
3.3 Appropriate use ........................................................................................................9
3.4 Performance features ...............................................................................................9
3.5 Warranty ................................................................................................................10
3.6 Approvals/Certications ..........................................................................................10
4 Notes on operating the device ���������������������������������������������������������������������������� 11
5 Views and connection assignment ���������������������������������������������������������������������12
5.1 Surface mount version............................................................................................12
5.1.1 Views ......................................................................................................................12
5.1.2 Connection assignment ..........................................................................................13
5.2 In-ceiling mount version..........................................................................................14
5.2.1 Views ......................................................................................................................14
5.2.2 Connection assignment ..........................................................................................15
6 Installation and commissioning ��������������������������������������������������������������������������16
6.1 Requirements at the installation site.......................................................................16
6.2 Mounting, connection and commissioning..............................................................16
6.2.1 Surface mount version............................................................................................16
6.2.2 In-ceiling mount version..........................................................................................19
7 Preparingtocongure �����������������������������������������������������������������������������������������22
7.1 PicoRemote Box .....................................................................................................22
7.2 DMS / DLS recorder ...............................................................................................23
7.3 PView......................................................................................................................24
8 Conguration ��������������������������������������������������������������������������������������������������������25
8.1 Presets....................................................................................................................25
8.2 Basic functions........................................................................................................27
8.2.1 Camera ID ..............................................................................................................27
8.2.2 CCTV System .........................................................................................................28
8.2.3 Horizontal Flip.........................................................................................................29
8.2.4 Lens Select .............................................................................................................29
8.2.5 Color .......................................................................................................................29
8.2.6 Day / Night Setup....................................................................................................29
8.3 Image Functions .....................................................................................................30
8.3.1 Progressive Scan....................................................................................................30
8.3.2 Backlight .................................................................................................................31
8.3.3 Digital Zoom............................................................................................................31
8.3.4 White Balance.........................................................................................................32
8.4 Exit Menu ...............................................................................................................32

4
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
9 Cleaning�����������������������������������������������������������������������������������������������������������������33
10 Menu structure������������������������������������������������������������������������������������������������������34
11 Technical data �������������������������������������������������������������������������������������������������������35
12 Technical drawings�����������������������������������������������������������������������������������������������37
12.1 Surface mount version............................................................................................37
12.2 In-ceiling mount version..........................................................................................38
13 Pinout information������������������������������������������������������������������������������������������������39

5
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
1 About this document
1�1 Validity
This document applies to the vandal-resistant DualMode colour dome cameras (Day/Night)
DDF3000AV4-DN and DDF3000AV4-D .
The descriptions in this document are based on the software version ML 2�3 and apply to
all above-mentioned device variants. For simplication reasons, the term “DDF3000AV4”
is thus used. If text passages require distinctions to be made between the device variants,
the complete device names will be mentioned.
Pictures in this document may differ from the actual product.
1�2 Documents
Commissioning
The document entitled “Commissioning” contains the most important steps for the connection
and commissioning of the device.
InstallationandConguration(thisdocument)
The document entitled “Installation and Conguration” contains detailed descriptions of the
installation, connection, commissioning and conguration of the device. Safety instructions,
general notes and technical data are additionally provided.
The target audience is exclusively specially trained and authorized professionals (instal-
lers).
1�3 Conventions
This document contains various warning words and symbols that indicate potential sources
of danger. Various symbols and formats are used to maintain the clarity of the document.
DANGER
The warning word DANGER denotes an immediate danger that
may cause death or serious injury if it is not averted.
WARNING
The warning word WARNING denotes a possible danger that
may cause death or serious injury if it is not averted.
CAUTION
The warning word CAUTION denotes a possible danger that
may cause minor injury if it is not averted.
IMPORTANT
The word IMPORTANT denotes information for preventing
damage, incorrect congurations or incorrect actions.

6
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
NOTE
A NOTE offers information on principles, special features and
efcient procedure as well as general recommendations.
Expression Expressions in bold and italics generally indicate a control ele-
ment on the device (switches or lables) or on its user interface
(buttons, menu entries).

7
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
2 Safety instructions
Only use this unit if it is technically in proper working order, to the intended purpose and
while keeping safety and potential dangers in mind. Have malfunctions or damages elimi-
nated immediately!
Appoint a professional
Installation, mounting, connection, start-up and conguration of the unit may only be carried
out by trained and authorized professionals (installers).
Unless otherwise expressly specied, this also applies to the maintenance, testing and repair.
In doing so the regulations of the DIN VDE 0701 series of standards (repair, modication
and inspection of electrical appliances) must be followed in addition.
Read and pay attention to the documents
Carefully and completely read the documents included in delivery. Always pay attention to
the provided instructions, notes and warnings.
Regulations surveillance systems
The use of video and audio surveillance systems is strictly regulated in most countries.
Therefore, inform yourself on laws and regulations that govern individual applications be-
fore using the unit. Ensure compliance with these laws and regulations and also observe
regulations regarding data, working and environmental protection.
Donotmakemodications
Do not make any modications to the unit (neither to the software nor the hardware) without
consulting Dallmeier electronic. Improper modications can cause malfunctions or damages.
Dallmeier electronic accepts no liability for damages resulting from unauthorized or improper
modications to the unit.
Protection against condensation water
If the unit is brought from a cold to a warm environment, condensation water can form inside
the unit. Short-circuits may then lead to damage to the system. Wait up to 8 hours for the
unit to reach room temperature before starting it up.
Observe the rated voltage
The unit can be damaged or destroyed by the application of an incorrect voltage.
The mains voltage must always match the rated voltage of the unit. The rated voltage is
specied on the rating plate of the unit.
Observe ratings
Unsuitable ambient conditions and improper installation (mainly too high ambient tempera-
ture and insufcient ventilation) may reduce the unit’s life cycle. Ensure compliance with the
stated operating conditions (see technical data), requirements at the installation site and, if
applicable, maintenance regulations.
Expansion components/peripheral devices
Use only expansion components conforming with the technical data of the unit. Inappropriate
peripheral devices may result in the violation of local laws and regulations and damages to
the unit. In case of doubt, contact the sales partner responsible for your area.

8
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
Do not open the unit
Do not open the housing of the unit. There are no components inside the unit that require
maintenance by the user. The inspection, maintenance and repair with an open housing
must only be carried out by trained and authorized professionals (installers).
Penetration of foreign bodies and liquids
No objects or liquids may be allowed to get into the device. In this case, immediately dis-
connect the unit from the power supply (pull out the power plug). Contact the sales partner
responsible for your area.
Measures to be taken in the event of damage and burnt smell
If you notice burnt smell or formation of smoke from a unit, immediately disconnect it from
the power supply (pull out the power plug). Contact the sales partner responsible for your
area.
Disposal
Disconnect the unit from the power supply. Remove all connected units and system com-
ponents. Return the unit to your respective sales partner.

9
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
3 General notes
3�1 Scope of delivery
Included in the standard scope of delivery is:
1x DDF3000AV4
1x Documentation “Installation and Conguration” (CD)
1x Documentation “Commissioning” (in print)
The scope of delivery may differ depending on the ordered equipment, the device variant
or the country of destination.
The functional range of the device depends on the ordered equipment or device variant
and may differ from this document’s content. Certain functions and features may require an
activation that is subject to costs.
3�2 Transportation and packaging
Store the original packaging for transportation at a later date. Dallmeier electronic is not
responsible for damage resulting from unprofessional/improper transportation. The goods
should only be shipped in their original packaging.
If the original packaging is no longer available, ensure that the packaging used sufciently
protects the unit against damage, moisture, heat and cold.
3�3 Appropriate use
The DDF3000AV4 is a vandal-resistant high-resolution UWDR (Ultra Wide Dynamic Range)
Cam_inPIX® colour dome camera with DualMode video output (UTP / BNC) and 3-axis ad-
justment. It can be operated at 12V DC or 24V AC. The surface mount version is designed
for the installation on ceilings and walls, the in-ceiling version for the indoor installation in
suspended ceilings.
3�4 Performance features
The DDF3000AV4 is especially characterised by the following functions and properties:
lHorizontal resolution: 540 TV lines
lDigital Pixel System*) (DPS) chipset
l 1/3” DPS image sensor with Cam_inPIX®technology
l17-bit Digital Signal Processing
l High light sensitivity at F0.95, 50IRE: 0.5 lux and (-DN) 0.2 lux
lProgressive Scan image capture
l Progressive With Segmented Frames (PsF) image transmission
l ICR function for Day/Night switching
lAdvanced noise reduction
l Numerous image enhancement functions like AWB, AGC, BLC and extended Slow
Shutter
l Conguration via UTC (Up The Coax) commands or integrated joystick (selector)

10
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
lDualMode video output (UTP or BNC)
l Compact vandal-resistant housing with IP67 (surface mount version only)
l3-axis mount for camera and lens adjustment
l12V DC or 24V AC voltage supply
lDIN EN 50130-4 compliant
NOTE
For detailed information see chapter Technical data.
3�5 Warranty
The terms and conditions valid at the signing of the contract shall apply.
3.6 Approvals/Certications
The following approvals/certications were in effect at the time this document was produ-
ced:
l CE
l FCC
lUL
l ACA
lUVV-Kassen
lCB
lDIN EN 50130-4

11
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
4 Notes on operating the device
l The device can be operated at 12V DC or 24V AC.
lIf the device or the cables connected to the device are located near sources of strong
radiation, the video image may be distorted.
l The device is equipped with automatic gain control (AGC). In low light the image may
be altered (e.g. noise). This is not a malfunction.
lThe quality of the video image depends on the lighting and the monitor used to display
the video image.
lAutomatic white balance depends on the lighting used and can cause colour distortions
in articial light.
lPoor lighting can lead to faulty white balance.

12
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
5 Views and connection assignment
5�1 Surface mount version
5�1�1 Views
Fig. 5-1
3-axis mount
(Pan / Tilt / Rotation)
for camera and lens adjustment
Housing base with
camera support
Thread for PG16 cable gland
Lens
Camera housing
(with bubble)
Housing screw (T20 Torx)

13
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
5�1�2 Connection assignment
Fig. 5-2
A Hole for mounting screw
B Selector for camera conguration (with integrated Enter button)
CVideo preview output (3.5 mm phone jack)
D Locking screw (Rotation, z-axis)
ELocking screw (Tilt, y-axis)
F UTP/BNC switch
G Locking screw (Focal length)
H UTP port (RJ-45 jack)
IThread for housing screw
J Video output/power input terminal (12V DC / 24V AC)
K Locking screw (Focus)
L Thread for PG16 cable gland
MSealing ring
NOTE
For pinout information see chapter Pinout information.
A
E
E
D
D
K
G
C
F
H
J
I
I
I
M
A
L
L
A
B

14
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
5�2 In-ceiling mount version
5�2�1 Views
Fig. 5-3
Fig. 5-4
Ceiling clamp
Ceiling clamp
Camera housing
Thread for PG16 cable gland
Thread for M6 screw eye bolt
3-axis mount
(Pan / Tilt / Rotation)
for camera and lens adjustment
Trim ring (with bubble)
Housing screw (T20 Torx)
Housing screw (T20 Torx)
Housing screw (T20 Torx)
Ceiling clamp
Ceiling clamp
Suspended ceiling

15
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
5�2�2 Connection assignment
Fig. 5-5
AThread for housing screw
B Selector for camera conguration (with integrated Enter button)
CVideo preview output (3.5 mm phone jack)
D Locking screw (Rotation, z-axis)
ELocking screw (Tilt, y-axis)
F UTP/BNC switch
G Locking screw (Focal length)
H UTP port (RJ-45 jack)
I Video output/power input terminal (12V DC / 24V AC)
J Locking screw (Focus)
K Thread for PG16 cable gland
L M4 locking screw (Ceiling clamp)
NOTE
For pinout information see chapter Pinout information.
A
B
C
D
E
F
G
H
I
J
K
L
A
A
L
E
D

16
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
6 Installation and commissioning
6�1 Requirements at the installation site
Unfavorable local conditions may shorten the life of the product or lead to malfunctions.
Do not install/operate the device in places:
lwith large scale dust and dirt
lwith steam or oil vapors (e.g. kitchen)
lwith direct sunlight
lwith improper ambient temperatures (see technical data)
l near sources of strong radiation (i.e. X-rays, radio transmitters or magnetic elds)
lwith corrosive surroundings (e.g. gases or salt water).
6�2 Mounting, connection and commissioning
6�2�1 Surface mount version
You can mount the camera on a ceiling or a wall.
NOTE
The appropriate mounting template can be downloaded at
https://www.dallmeierpartner.de.
Cut the hole (Ø 22 mm) for cables out of the mounting template.
Pull all required cables suspended from the ceiling/wall through the mounting templa-
te.
 Afx the mounting template to the required position.
Fig. 6-1
Ceiling/wall
Drilling
Dowel
Mounting screw
(4×25mm oval/llister head
screw with cross recess)

17
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
Drill holes for dowels at the 3 marked locations.
Detach the remaining mounting template.
Insert appropriate dowels into the drilled holes.
Loosen (counter-clockwise) the 3 housing screws (T20 Torx) and remove the camera
housing.
 Pull all required cables suspended from the ceiling/wall through a PG16 cable gland.
Screw the PG16 cable gland in the appropriate thread (see Fig. 5-1).
 Mount the housing base with the 3 mounting screws (4×25mm oval/llister head screw
with cross recess) to the ceiling/wall using the mounting holes (A, see Fig. 5-2).
WARNING
Danger of death from lightning strike!
Do not connect / disconnect the video cable during a thunder-
storm!
WARNING
Danger of death from electric shock!
Disconnect the power supply unit from the mains socket before
connecting the camera!
NOTE
In order to comply with the UL requirements, you have to use a
UL-certied, limited power source (LPS) Class 2 power supply
unit.
NOTE
The camera is provided with internal inverse-polarity protec-
tion.
Connect the camera via terminal (J, see Fig. 5-2) or UTP port (H) to an appropriate power
supply unit and a CVBS or UTP device. Ensure the correct pin assignment.
NOTE
For pinout information see chapter Pinout information.
Select the relevant video output type using the UTP/BNC switch (F).
Connect the power supply unit to the mains socket.
If necessary, connect the camera to a CVBS monitor using the video preview output
(C).
Loosen the locking screws (D), (E), (G) and (K, see Fig. 5-2).
Adjust the camera and lens using the 3-axis mount (see Fig. 5-1).
Adjust the focal length and focus.
Check the video image on the CVBS monitor.

18
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
 Fix the locking screws (D), (E), (G) and (K, see Fig. 5-2).
Press and hold the selector (B) for approx. 2 seconds to open the OSD conguration
menu. Congure the camera settings.
Disconnect the video preview CVBS monitor.
Mount the camera housing with the 3 housing screws (T20 Torx) to the housing base.
Pay attention to the accurate t of the sealing ring (M).
Fig. 6-2
WARNING
Danger of injury from camera falling down!
Ensure that the camera base and camera housing are securely
mounted!
Sealing ring
Housing screw
(T20 Torx)

19
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
6�2�2 In-ceiling mount version
Cut a recess (Ø 143 mm) in the suspended ceiling using a drywall utility saw or a
jigsaw.
Tighten the M6 screw eye bolt on the bottom side of the housing.
Fig. 6-3
Attach a ceiling hook to the supporting structure.
Attach the safety wire to the M6 screw eye bolt and the ceiling hook.
Loosen (counter-clockwise) the 3 housing screws (T20 Torx) and remove the trim ring.
Pull all required cables suspended from the ceiling through a PG16 cable gland. Screw
the PG16 cable gland in the appropriate thread (see Fig. 5-3).
Insert the camera housing into the cut out recess (Ø 143 mm).
Fig. 6-4
Ø 143 mm
Suspended ceiling
M6 screw eye bolt
Supporting structure
Ceiling hook
Safety wire
Carabiner

20
Dallmeier electronic
DDF3000AV4-DN / DDF3000AV4-D
Tighten the M4 locking screw (L, see Fig. 5-5) of both ceiling clamps in clockwise direc-
tion using a Phillips screwdriver.
Fig. 6-5
Fig. 6-6
WARNING
Danger of death from lightning strike!
Do not connect / disconnect the video cable during a thunder-
storm!
WARNING
Danger of death from electric shock!
Disconnect the power supply unit from the mains socket before
connecting the camera!
NOTE
In order to comply with the UL requirements, you have to use a
UL-certied, limited power source (LPS) Class 2 power supply
unit.
NOTE
The camera is provided with internal inverse-polarity protec-
tion.
Ceiling clamp Ceiling clamp
Suspended ceiling
Phillips screwdriver
Locked ceiling clamp Locked ceiling clamp