DeFelsko PosiTector GLS Service manual

Gloss Meter
On-Gage Help Reference
Ayuda en el Medidor |On-Gerät-Hilfe |Aide sur l’instrumentation

Introduction
This Reference is a compilation of the On-Gage Help that is available on your
PosiTector gage. To view these help items on the gage, enter the gage menu and touch
the icon or press the button with the desired menu item selected.
For an overview of the use and operation of your instrument, refer to its included
Instruction Manual or download a digital PDF at www.defelsko.com/manuals.
Update your gage to ensure your PosiTector includes these latest help references.
Instructions are available at www.defelsko.com/updates.

Page 1
Contents
Memory ........................................................................................................................
View .......................................................................................................................
Off ..........................................................................................................................
On ..........................................................................................................................
Clear ......................................................................................................................
Statistics ......................................................................................................................
Statistics ................................................................................................................
Clear ......................................................................................................................
HiLo Alarm .............................................................................................................
Differential ..............................................................................................................
Calibration Settings ......................................................................................................
Edit .........................................................................................................................
Open ......................................................................................................................
New Cal Standard ..................................................................................................
Delete ....................................................................................................................
View .......................................................................................................................
Power-On Cal ........................................................................................................
Cal Standard ..........................................................................................................
Calibrate ................................................................................................................
Setup ...........................................................................................................................
Set Clock ...............................................................................................................
Reset .....................................................................................................................
Units .......................................................................................................................
Battery Type ..........................................................................................................
Sound ....................................................................................................................
Touch .....................................................................................................................
Backlight ................................................................................................................
Flip Lock ................................................................................................................
Geometry ...............................................................................................................
Language ...............................................................................................................
Gage Info ...............................................................................................................
Haze Index .............................................................................................................
Connect .......................................................................................................................
USB .......................................................................................................................
Sync.net Now ...................................................................................................
USB Drive ........................................................................................................
JSON Files .................................................................................................
HTML Report .............................................................................................
Auto Sync .net .................................................................................................
Updates .................................................................................................................
Help .............................................................................................................................
Power Off .....................................................................................................................
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
4
5
5
5
6
6
6
7
7
7
7
7
8
8
8
8
8
9
9
9
9
10
10
10
10
11
12

Page 2
Memory
The PosiTector GLS Standard has internal memory storage for recording measurement
data. Stored measurements can be reviewed on-screen or downloaded to a computer.
Measurements are date and time-stamped. Store up to 1000 readings (per probe) into a
single batch.
The memory icon appears and basic statistics are displayed when the Gage is set to
store measurement data.
NOTE:
Remove the last reading by pressing (-).
View
Use the Up or Down buttons to scroll through information, statistical summary, and a list
of each reading in the currently opened batch. Press the center navigation button to
exit.
Off
Turns memory off and stops recording (stored readings remain in memory)
On
Turns memory on and begins recording measurements.
Clear
Removes all stored readings from memory.

Page 3
Statistics
Menu option for configuring Statistics and HiLo Alarm modes.
Statistics
Statistics mode continually displays/updates average, standard deviation, min/max
thickness and number of readings while measuring.
When selected, the statistics icon and statistical summary will appear on the display.
Ignore the last measurement by pressing the (-) button. Press (+) to clear statistics.
Clear
Clears all on-screen Statistics and HiLo tabulations.
HiLo Alarm
Allows the Gage to visibly and audibly alert the user when measurements exceed
user-specified limits.
When HiLo Alarm is selected, the current Lo setting is displayed. Adjust using the (-) or
(+) buttons. Select Next to accept this value. The current Hi setting is now displayed.
Repeat to adjust the Hi setting.
Each measurement will be compared to the defined Hi and Lo limits. The Gage beeps if
results are within those limits. A single low tone will sound if the reading is below the Lo
limit, and a high tone if it is above the Hi limit. Press (+) to clear HiLo readings.
The Statistics icon will appear on the display.
Differential
Automatically calculates the difference between the current reading and a stored
reference value.

Page 4
Calibration Settings
Calibrate the PosiTector GLS probe to known standards by using included gloss
calibration standard (tile) or user supplied calibration standard. Place the probe on a
known standard and select the Calibrate menu item. Alternatively, if Power-On Cal is
selected in the Cal Settings menu the gage will perform a calibration every time the
gage is powered on.
Edit
Select a calibration standard from a list of saved standards to edit its Gloss Unit value
and name.
NOTE:
The calibration standard included within the protective base plate cannot be edited.
Open
Select a calibration standard from a list of saved standards. The calibration standard at
the top of the list is the one included within the protective base plate of the PosiTector
GLS probe.
New Cal Standard
Stores a new calibration standard into memory.
Adjust the Gloss Unit (GU) values using the on-screen keypad or by pressing (-) or (+).
Enter a name or serial number to identify the Standard using the on-screen QWERTY
touch keyboard.
Select OK, then follow the prompts to take a measurement of the desired gloss
calibration standard.
Delete
Menu option for configuring Statistics and HiLo Alarm modes.
View
Displays a list of stored standards and their Gloss Unit Values.

Page 5
Power-On Cal
When selected, the Gage will perform a calibration every time the gage is powered-on,
using the calibration standard that was active when the probe was last used.
NOTE:
Power-On Cal will only operate if the active calibration standard is incorporated in a
protective base plate.
Cal Standard
For some applications, it may be desirable to calibrate the PosiTector GLS probe to a
different calibration standard than the one included with the probe. Add and manage up
to 99 calibration standards from this menu.
Calibrate
Calibrate the PosiTector GLS probe to known standards by using included gloss
calibration standard (tile) or user supplied calibration standard. Place the probe on a
known standard and select the Calibrate menu item. Alternatively, if Power-On Cal is
selected in the Cal Settings menu the gage will perform a calibration every time the
gage is powered on.
NOTE:
Ensure the calibration standard is clean and lint free. To clean the standard:
Remove the protective base plate, holding it from the bottom.
Using the included lens cleaning wipe, gently wipe the surface of the standard. Examine
the calibration standard to ensure that it is dry, clean, and free of any debris or defects.
A scratched standard should not be used to calibrate the probe and should be replaced.
Do not reuse the cleaning wipe. Best results are obtained by rubbing in one direction
only and by using a new portion of the wipe for each cleaning pass.
WARNING:
Do not substitute other chemicals or cleaning wipes in this procedure. Replacement
lens cleaning wipes are available.

Page 6
Setup
Set configuration options for the Gage.
Set Clock
All measurements are date and time stamped (24 hour format) when stored into
memory. It is therefore important to keep both the date and time current using this menu
option. Use the Up and Down buttons to scroll, and the (-) and (+) buttons to adjust
value. The Gage’s date and time can also be viewed in Gage Info and on top of the
main menu.
Reset
Restores factory settings and returns the Gage to a known condition. The following
occurs:
All batches, stored datasets, batch names, and screen captures are erased.
The default calibration standard that was included with the probe is selected, and all
other calibration standards are deleted.
Menu settings are returned to the following:
Memory = OFF
Statistics = OFF
HiLo Alarm = OFF
Differential = OFF
Scan Mode = OFF
Auto Dim = ON
Bluetooth & Stream = OFF
BLE Keyboard = OFF
WiFi & Access Point = OFF
Power-On Cal = OFF
Display = None
Perform a more thorough Hard Reset by powering down the Gage, waiting several
seconds, then simultaneously holding both the center navigation and (+) buttons until
the Reset symbol appears. This returns the instrument to a known, out-of-the-box
condition. It performs the same function as a menu Reset with the addition of:
Bluetooth Pairing info is cleared. Menu settings are returned to the following status:

Page 7
Units = Gloss
Touch = ON
Flip Lock = OFF
Auto Sync .net = ON
Sound = Medium
Language = English
Battery Type = Alkaline
Backlight = Normal
Bluetooth Smart = OFF
USB Drive = ON
NOTE:
Date, Time and WiFi are not affected by either Reset.
Units
Select between Gloss Units (GU) or % Reflectance.
Battery Type
Selects the type of batteries used in the Gage from a choice of Alkaline, Lithium or
NiMH (nickel-metal hydride rechargeable). The battery state indicator symbol is
calibrated for the selected battery type. No damage will occur if the battery type used in
the Gage does not match the selected battery type.
Sound
Adjusts the volume of built-in speaker (Off, Low, Medium, High).
Touch
Allows the touch screen functionality to be disabled. All gage functions can also be
controlled using the navigation buttons.
Backlight
Selects display brightness (Sun, Normal or Night). If Auto Dim is enabled (default), the
display dim slightly after a period of no activity to conserve battery life. Press the Down
button to brighten the display.

Page 8
Flip Lock
Disables the Auto Rotate feature by locking the display in its current orientation.
Geometry
(PosiTector GLS2060 and GLS206085 models only)
Select the angles to display when taking measurements.
Language
Converts displayed and printed words to the selected language.
Gage Info
Displays the model number and serial number, probe type and serial number,
PosiSoft.net registration key, the amount of remaining memory for storage of readings,
date and time, and software packages.
For security purposes, the registration key is required to add the Gage to your free
PosiSoft.net account.
Haze Index
(PosiTector GLS2060 and GLS206085 models only)
Select this option to display and record the Haze Index while taking measurements.
Haze Index is calculated as the difference between the measurement in GU at 60° and
20°.
NOTE:
Haze Index in accordance with ASTM D4039 is applicable to nonmetallic specimens
having a 60 degree specular gloss value greater than 70.

Page 9
Connect
Configure communication and connection options for the Gage.
USB
Connect the Gage to a PC/Mac using the supplied USB-C cable. View and print
readings and graphs with universal web browsers/file explorers or using PosiSoft
Desktop.
NOTE:
While connected, power is supplied through the included USB-C cable. The batteries
are not used and the body will not automatically power down.
Sync.net Now
When selected, the Gage immediately synchronizes stored measurement data to
PosiSoft.net (USB connection required to a computer running PosiSoft Desktop).
Alternatively, select Auto Sync.net from within the USB connect menu to automatically
synchronize upon connection to a PC. Additional measurements added to memory
while connected are synchronized only when the USB cable is disconnected and
reconnected, or when the Sync.net Now option is selected.
NOTE:
PosiSoft Desktop is required when using USB connections to synchronize
measurements with PosiSoft.net.
USB Drive
When USB Drive is enabled, the PosiTector is recognized as a USB mass storage
device which provides a simple interface to retrieve stored data in a manner similar to
USB flash drives and digital cameras. USB Drive is also required to import stored
measurements into PosiSoft Desktop. Once connected, any computer can view
measurements stored in memory by navigating a virtual drive labeled PosiTector using
the supplied USB-C cable.
NOTE:
While connected, power is supplied through the included USB-C cable. The batteries
are not used and the body will not automatically power down.

Page 10
JSON Files
When enabled (default), JSON schema files will be available in PosiSoft USB drive.
Files can be parsed in to databases and custom software applications.
NOTE:
Disabling this option may reduce the time required for the computer to recognize the
PosiTector when first connected via USB.
HTML Report
When enabled (default), a formatted HTML report is viewed by selecting the index.html
or START_HERE.html file found in the root directory. Optionally, text (.txt) files located
in each batch folder provide access to measurement values. Stored readings and
graphs can be viewed or copied using universal web browsers or file explorers.
NOTE:
Disabling this option may reduce the time required for the computer to recognize the
PosiTector when first connected via USB.
Auto Sync .net
When enabled, measurements will automatically synchronize with PosiSoft.net when
connected to a computer running PosiSoft Desktop. Additional measurements added to
memory while connected are synchronized only when the USB cable is disconnected
and reconnected, or when the Sync.net Now option is selected.
NOTE:
PosiSoft Desktop is required when using USB connections to synchronize
measurements with PosiSoft.net.
Updates
Determines if a software update is available for your Gage.
To perform an update the Gage must be connected to an internet connected computer
running PosiSoft Desktop.
See www.defelsko.com/update
WARNING:
The Gage will perform a Hard Reset after an update. All stored measurements will be
erased from memory.

Page 11
Help
When a Menu option is highlighted, the (i) icon indicates on-gage help is available.
Press (+) or touch the (i) icon to display the help. Update your gage to ensure that you
have the latest on-gage help information.
A formatted PDF containing all on-gage help items is available at
www.defelsko.com/help.
Menu Operation
To access the Menu, power-up the gage, then press the center navigation button. Either
the keypad or touch screen can be used to navigate the menu. If desired, touch screen
functionality can be disabled within the Setup > Touch menu.
Select a menu option by touching it, or use the Up and Down buttons to highlight the
desired option and press the center navigation button to select it.
On menus longer than one page, the current page number is displayed below the menu
name. Navigate between pages using the Up button when the first menu item is
selected, or Down button when the last menu item is selected. If using touch, navigate
between pages by touching the left or right arrow, or by swiping up or down.
Press the (-) button or swipe right to return to a previous screen. Select Exit to close the
Menu.
A menu option with a > indicates that a sub-menu exists for the Menu option. Select
the option to display its sub menu.
Screen Capture
Press both (-) and (+) buttons simultaneously to save an image of the current display.
The last 100 screen captures are stored in memory and can be accessed when
connected to a computer via PosiSoft USB Drive.

Page 12
Power Off
To conserve battery life, the gage will automatically go to sleep after 5 minutes of
inactivity and enter Sleep Mode. While in Sleep Mode the gage powers up significantly
faster— convenient when moving between parts or locations. The gage will completely
power off after 4 hours of inactivity. Alternatively, select Power Off from the main menu.
All settings are retained.