DeLonghi DCH6031 User manual

De’Longhi Appliances via Seitz, 47 31100 Treviso Italia 5711411511 /10.13
Proudly distributed by
De’Longhi Australia Pty Limited
P.O. BOX 4540
CASULA MALL NSW 2170
Customer Service Ph: 1800 126 659
Fax: [phone]
www.delonghi.com.au
e-mail: [email protected]
De’Longhi New Zealand Limited
25 Carbine Road
Mt Wellington
Auckland, New Zealand
P.O. Box 58-056 Botany
MANUKAU 2163
Customer Service Ph: 0508 200 300
Fax: [phone]
www.delonghi.com.nz
e-mail:[email protected]

DCH6031
CERAMIC FAN HEATER
Instructions for use

2
DESCRIPTION
D
E
F
C
B
A
Fig. 1

3
IMPORTANT WARNINGS
Safety warnings
Danger!
- Do not use the appliance near show-
ers, bathtubs, sinks, swimming pools,
etc.
- If the power cable is damaged, it must
be replaced by the manufacturer, an
authorised service centre or a qualied
electrician in order to eliminate all risk.
- The appliance must not be placed im-
mediately under a xed power socket.
Important!
- Always use the appliance in an upright
position.
- The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been gi-
ven supervision or instruction concer-
ning use of the appliance by a person
responsible for their safety. Children
should be supervised to ensure that
they do not play with the appliance.
- The use of extension leads is not re-
commended. However if they cannot
be avoided, follow the instructions
accompanying the extension lead and
never exceed the power limit marked
on the extension.
Danger of burns!!
- Do not use the appliance to dry laun-
dry. Do not obstruct the air intake and
outlet grilles (danger of overheating).
- The heater must be positioned at least
50 cm from furniture or other objects.
- Do not use the appliance near walls,
furniture, curtains, etc.
- Do not use the appliance in rooms with
a oor area of less than 4m2.
Please note:
- Before putting the appliance away,
make sure it is completely o and
unplugged from the mains socket.
Wrap the cable around the base. Do
not store in dusty atmospheres.
- Room temperature should be between
0 and 30° C.
- Do not rest anything on the appliance.
- To avoid the safety system resetting
accidentally, this appliance must not
be powered through an external on/
o device such as a timer, or connected
to a circuit which is turned o and on
regularly by the energy supplier.
IMPORTANT: To avoid overheating,
never under any circumstances co-
ver the appliance during operation
as this would lead to a dangerous rise in
temperature.
INTRODUCTION
Thank you for choosing a De’Longhi product.
Please take a few minutes to read these instructions.
This will avoid all risks and damage to the appliance.
Symbols used in these instructions
Important warnings are identied by the symbols below.
It is important to respect the warnings.
Failure to respect the warnings could lead to electric shock,
serious injury, burns, re or damage to the appliance.
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.

4
Danger of burns!!
Failure to observe the warning could result in burns or scalds.
Please note:
This symbol indicates recommendations and important
information for the user.
Safety functions
-Safety device: the appliance is tted with a safety
device which switches it o in the event of accidental
overheating (e.g. obstruction of air intake and outlet
grilles, motor turning slowly or not at all).
To reset, unplug the appliance from the mains socket for
a few minutes, remove the cause of overheating then
plug in again.
-Tip over safety device: a tip over safety device (D)
turns the appliance o if it falls over or is positioned
inappropriately in such a way as to jeopardise safety.
When the appliance is placed back in a vertical position
it starts again automatically.
DESCRIPTION
(see g. 1)
A Mode selector
B Thermostat
C Indicator light
D Tip over switch
E Filter protection grille
F Filter
USE
Installation
The appliance can be used on any horizontal surface.
Do not overload the electrical circuit. Avoid using the same
socket for other appliances.
Electrical connection
- Before plugging into the mains, make sure the voltage
of your mains supply corresponds to the value V indica-
ted on the appliance and that the socket and power line
are appropriate for the load required.
- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/
EC ON ELECTROMAGNETIC COMPATIBILITY.
Operation and use
1. Make sure the selector (A) is in the “0” position before
plugging the appliance into the mains socket.
2. Plug into the mains socket.
3. Turn the appliance on by placing the thermostat (B) in
the Max position and the mode selector (A) in one of the
following positions: /1/2/3.
The following modes are available:
- Summer mode (fan only): turn the mode selector to the
position (the light comes on).
- Low power operation: turn the mode selector to posi-
tion“1”.
- Medium power operation: turn the mode selector to
position“2”.
- High power operation: turn the mode selector to posi-
tion“3”.
- To turn the appliance o: turn the mode selector to the
“0”position and the thermostat to the position, then
unplug from the mains.
Adjusting the thermostat
When the room has reached the required temperature, turn
the thermostat (B) slowly anticlockwise until you hear a
“click”. The thermostat will then keep room temperature at
the selected level automatically.
Frost prevention mode
With the thermostat dial at minimum and the mode se-
lector (A) on “3”, the appliance maintains room temperature
at about 5°C, preventing freezing with minimal energy con-
sumption.
MAINTENANCE
- Always unplug from the mains socket before cleaning.
- During the season when the appliance is in use, clean
the air intake and outlet grilles regularly using a vacuum
cleaner.
- To clean the lter, remove the rear grille (E) by pulling it
outwards (g. 1).
Remove the dust lter (F) which retains impurities in
the air drawn in from the room, blow on it lightly then
replace in the appliance.
- Never use abrasive powders or solvents to clean the ap-
pliance.
TECHNICAL CHARACTERISTICS
Power supply See rating plate
Absorbed power “