DELTA DORE RADIO TYBOX User manual

RADIO TYBOX
User guide
Wireless programmable thermostat
1-zone pack or 2-zone pack
RADIO TYBOX
*2702001_rev1*
DELTA DORE - Bonnemain
35270 COMBOURG - FRANCE
E-mail: [email protected]
Device compliant with the requirements of directives:
R&TTE 1999/5/CE
Because of changes in standards and equipment, the characteristics
given in the text and the illustrations in this document are not binding
unless confirmed by Delta Dore.
• Carefully read these instructions prior to use.
• Do not attempt to repair the unit yourself;
an after-sales service is available.
Warnings
Off mode
Absence mode
Timer mode
Automatic mode
Time setting
Programming
Set-point temperature
adjustment
Continuous mode
Modification
buttons
Selector
knob position Selector
knob
RADIO TYBOX
Presentation
This manual is for the RADIO TYBOX transmitter.
1-zone pack (1 transmitter)
2-zone pack (2 transmitters)
This thermostat lets you program your heating system
to Comfort or Economy mode.
Override
In automatic mode, override is used to switch from
Comfort to Economy mode (or conversely) until the
next program change.
Press the override button
6:00 8:00 00:0000:00 17:0015:30 23:00
Override
currently active
At 17:00, the program will
return to its usual program
.
To cancel the current override,
press the button once more.
E.g. It is 15:30 and you would like to switch to Comfort
mode before the set time (17:00).
Current day programming
Turn the knob to AUTO.
Your thermostat will function according to the program.
Automatic mode
Override
Information
button
Display in automatic mode
Time
Current day
Room
temperature
Current mode
Current day
programming
Heating
demand mode
NOTE: Depending on the configuration during
installation, your unit will continuously display the
set-point temperature or the room temperature.
To change these settings, refer to the “installation
guide”, or contact our customer service department
or your installer.
This mode is used to choose a set-point temperature
for a given amount of time.Turn the knob to .
To make changes to the current timer mode,
press OK once more.
To cancel the current timer mode, turn the knob.
Continuous mode
Choice of set-point
temperature (from 5 to 30°C)
Set-point
temperature
Confirm
Modification of the set-point
temperature
This mode is used to choose a set-point temperature
that remains constant.
Turn the knob to .
Timer mode
Set-point temperature setting (from 5 to 30°C)
Confirm
Return to AUTO mode at
the end of the countdown
Confirm
Adjustment of the duration from 15 minutes
to 72 hours (in increments of 15 minutes)
To exit this mode, turn the knob.
This mode lets you place your home under Frost
Protection if you need to leave for several days.
Turn the knob to .
To make changes to the current absence mode,
press OK once more.
This mode shuts down your heating system.
Turn the knob to .
Off Mode
Room
temperature
Return to AUTO mode at
the end of the countdown
Set-point temperature setting (from 5 to 15°C)
Confirm and start the calendar countdown.
Confirm
Adjustment of the number of days (1 to 365)
E.g. For a departure on 1 March and a return
on 16 March, program 15 days of absence.
Automatic operation will resume on
16 March at midnight.
Absence mode
Turn the knob to .
The days flash.
Press + or - to change the day, then press OK to
confirm and continue on to the next setting.
Repeat the operations to set the hours and minutes.
To leave the “time setting” mode, turn the knob.
Minutes
Hours
Days
(1 : Monday ...
7 : Sunday)
Time setting
NOTE: If the unit is configured for a daily program,
the days setting is not offered.
Set-point temperature setting
Turn the knob to .
To exit this mode, turn the knob.
Comfort set-point temperature setting
(from 5 to 30°C in increments of 0.5°C)
Confirm
Go on to temperature setting
Economy
Adjustment of the Economy temperature
setting (from 5 to 30°C)
Confirm
Depending on the system configuration (menu 1-08),
“conf” may be displayed for the set-point
temperature.
This set-point temperature cannot be modified.
If this is the case, the Comfort set-point temperature
can be adjusted on your heat emitter (convector, panel
heater, thermostatically controlled valve, etc.).
Press and hold
until you reach 06:00
Press and hold
until you reach 08:00
Press and hold
until you reach 17:00
Press and hold
until you reach 23:00
Press and hold
until you reach 00:00
Copy and confirm
or confirm
E.g. Comfort from 6:00 to 8:00 and from 17:00 to 23:00
6:00 8:00 00:0000:00 17:00 23:00
Programming
Turn the knob to PROG.
The default program is a Comfort period from
6:00 to 23:00.
1. Creating your program
Programming starts on day 1 at midnight.
Press the or buttons to create different Economy
or Comfort periods.
2. Confirming and copying the program
Press and hold the OK button for 3 seconds to confirm
the program you created and copy it to the next day.
3. Confirming the program
Press the OK button to confirm and continue on to the
next day to program it separately.
Day
1st time
slot
Comfort period
adjustment
Economy period
adjustment
OR
Checking your program
Press the button repeatedly to check the accuracy
of the Comfort and Economy periods you created.
Press OK to check the next day.
Exiting the programming mode
Turn the knob to another mode.
Program
profile
Verification
of the different
or periods
Time slot
consulted
NOTE: Depending on the configuration made during
installation, programming can be weekly or daily.
Likewise, this programming may be done in increments
of one hour, 30 minutes, or 15 minutes.To change these
settings, refer to the “installation guide”, or contact our
customer service department or your installer.

• the electrical consumption in euros of the
heating, water heater (DHW) and other electrical
appliances (lights, household appliances, etc.).
If you have the RADIO TYWATT option on your
installation
• the program of the current day per zone.
Comfort periods
e.g. zone 1
Heating
Hot water production
other
• the outside temperature
With an associated outside sensor
• total consumption of your installation
If you have the RADIO TYWATT option on your instal-
lation
To reset all meters, press and hold the init. button for 5
seconds.
Press repeatedly
Reset
Consumption
Press repeatedly
Open Window
E.g. With an associated door/window magnetic contact
RADIO TYBOX
is on standby
RADIO TYBOX
is “activated” and
displays the status
of the installation
Press a button
Frost Protection control
Boiler
Activating the RADIO TYBOX
With a door/window magnetic contact
If a door/window magnetic contact is associated,
the heating switches to Frost protection mode if the
door/window is opened.
The RF 640 and RF 650 receivers allows you to
associate up to 8 home automation products (door/win-
dow magnetic contact, alarm control centre, remote
controls, etc.) with the RADIO TYBOX.
To associate the different products, refer to the RADIO
TYBOX installation guide.
Activating the RADIO TYBOX
The receiver (RF 640 or RF 650) instantaneously takes
into account all information coming from a home
automation product (e.g. an open window).
To display this information on the RADIO TYBOX, the
RADIO TYBOX must be “activated” by pressing a
button.
The update can take a few seconds.
Home automation features
With a TYXAL alarm control unit
If a TYXAL alarm control unit is associated.
When you activate the alarm, the heating will
automatically switch to Economy mode until the next
program change.
When you activate the alarm, the heating will
automatically switch to Economy mode until the next
program change.
This override can be cancelled on the RADIO TYBOX,
by pressing the override button or by turning the
selector knob.
With a TYXIA Transmitter
With an associated TYXIA transmitter:
- pressing the button once switches the heating
to Comfort mode until the next program change.
- pressing the button once switches the heating
to Economy mode until the next program change.
The command can be cancelled:
- on the TYXIA transmitter, by pressing ,
- on the RADIO TYBOX, by pressing the override
button or by turning the selector knob.
E.g. With an associated remote control
With a TYDOM 200 remote control
From the home domain , pressing the tactile
button switches off the heating.
This off command is cancelled by pressing .
Pressing the tactile or button once switches the
heating to Comfort or Economy mode, until the next
program change.
The command can be cancelled:
- on the TYDOM 200 remote control, by pressing the
tactile button,
- on the RADIO TYBOX, by pressing the override
button or by turning the selector knob.
With a TYDOM telephone transmitter
By calling the TYDOM telephone transmitter, let the
synthesized voice guide you to determine or modify the
status of the heating system (see the TYDOM
transmitter instructions).
Home automation features
123
456
789
0#
Separate the thermostat
from its base.
Position the thermostat
on its base.
Lock the thermostat.
Replace the batteries, making
sure they are the right way round.
1
2
3 4
Replacing batteries
When the battery level symbol appears, you have
around 1 month to change the batteries
(two 1.5 V alkaline batteries, LR03 or AAA).
The following precautions must be respected:
- Ensure that the +/- polarities are correctly placed
when the battery is fitted into the unit.
- Do not dispose of used batteries in unauthorized
places (you should respect the environment by taking
the batteries to a suitable collection site).
- Do not recharge the batteries.
-You have approximately 30 seconds to change the
batteries before the time is reset to zero
(if this happens, reset the date and time).
Battery level symbol
The programs cannot be modified and the set-point
temperature settings are limited (comfort: 16 to 22°C,
Economy: 13 to 19°C, Frost Protection: 5 to 11°C).
Refer to the installation guide (menu 2-01) or contact your ins-
taller or our customer service department.
Your heating system is in Frost-Protection mode.
The thermostat is in the , , PROG or position .
The unit displays: dEF 6.
There is a communication fault between the RADIOTYBOX
and the RF 640 or RF 650 receivers.
Bring the transmitter nearer to the receiver.
The indication is displayed.
The batteries are low.
Change the batteries, making sure they are the right way
round.
The device only displays the time and the room
temperature.
RADIO TYBOX is in screen saver display mode, but all the
heating features are running.
Press a button to "activate" the display.
The update can take a few seconds.
Nothing is displayed on the room unit screen.
There is no power supply.
Check the batteries.
The unit is in time setting mode.
You took too much time in changing the batteries.
Set the time. All other settings have remained unchanged.
When setting the time, there is no option to set the day.
RADIO TYBOX is set to daily programming.
To switch to weekly programming, refer to the installation guide
(menu 1-01) or contact your installer or our customer service
department.
When creating a program, the and symbols do not
appear on the screen.
Program changes were not authorized during installation.
Refer to the installation guide (menu 2-01) or contact your ins-
taller or our customer service department.
The temperature displayed does not match the
temperature measured in the room (thermometer).
Refer to the installation guide (menu 2-02) or contact
your installer or our customer service department.
Troubleshooting
The purpose of this section is to help you quickly solve
the most common problems that you may encounter
with your product during use.
If you're unsure, or if the problem persists or isn't in
this list, contact our customer service department.
During the AUTO, or modes, press the i
button repeatedly to find out:
•the room temperature or the set-point
temperature (depending on the configuration
during the installation)
If your thermostat displays the temperature of the room
Information button
Set-point temperature display
Return to normal display
(automatic after about 40 seconds)
The display of all information related to home
automation features (outside temperature, consumption
indication, etc.) requires an “activation” phase from the
RADIO TYBOX (see the home automation features
section).