DeltaTRAK DT-8806H User manual

User Guide
DT-8806H Non-Contact Forehead Infrared Thermometer
Model 15004
Please read this manual before operating unit.
Important safety information inside.

1
Contents
General Description
General Description..................................................................1
Safety Information ...................................................................1
Features .................................................................................2
Intended Use ..........................................................................2
Configuration ..........................................................................3
LCD Screen Indicators ............................................................3
Description of Symbols ............................................................4
Technical Specifications ...........................................................4
Advice for First Use and Calibration ..........................................5
Use ........................................................................................5
Measuring Operation ...............................................................6
Advice ....................................................................................7
Maintenance and Cleaning .......................................................7
Troubleshooting ......................................................................8
Compliance ............................................................................9
Non-Contact Forehead IR Thermometer is specifically designed to take
human body temperature.
Safety Information
• This device must only be used for the purposes described in this instruction manual.
• This device must only be used in an operating temperature range between 10°C to
40°C (50°F to 104°F).
• Do not expose this thermometer to electric shocks. Do not expose this thermometer
to extreme temperature conditions of > 50°C (122°F) or < 0°C (32°F).
• Do not use the device in relative humidity higher than 85%.
• Do not use the device near large electromagnetic fields such as found with cordless
or cell phones.
• Keep the device away from water and heat, including direct sunlight.
• Do not drop or strike the device, and do not use if damaged.
• Accuracy of measurements may be affected when the forehead is covered by hair,
perspiration, or clothing. (See Part 10-4)
• Maintain a measuring distance of 5 cm to 15 cm (2 in to 5.9 in). (See Part 10-4)
• Allow device to acclimate to ambient temperature for 15 to 20 minutes before using.
• Temperature may also be taken behind the ear lobe. (See Part 10-5)
• Clean the device surface with a cotton pad lightly moistened with 70%
Isopropyl alcohol.
Important Information
• Before taking temperature remove hair and perspiration from forehead.
• Select “Body” mode to measure body temperature.
• Select “Surface” mode to measure the surface temperature.

2
Features
• Precise non-contact measurements
• User selectable °C or °F
• Selectable Body and Surface mode
• Set Alarm value
• Memory holds 32 points of temperature data
• Automatic data hold
• Auto power off
• Automatic selection range and display resolution 0.1°C (0.1°F)
• Backlight LCD display
Intended Use
Non-Contact Forehead IR Thermometer is designed for forehead
temperature measurement for infants and adults without contact to human
body.
Non-Contact Forehead IR Thermometer can also be used to measure
the temperature of a baby bottle, bath or room temperature (by using the
Surface mode).
Measurement Method Normal Temp °C Normal Temp °F
Rectal 36.6 to 38 97.8 to 100.4
Oral 35.5 to 37.5 95.9 to 99.5
Axillary 34.7 to 37.3 94.4 to 99.1
Ear 35.8 to 38 96.4 to 100.4
Normal Temperatures According To Measurement Method
The temperature of the human body varies throughout the day. It can also
be influenced by the following factors: age, sex, type and thickness of skin.
• Use of this thermometer is not intended as a substitute for consultation with
a physician.
• Should a problem occur with device, please contact retailer.
• Do not attempt to repair the device.
• Follow EMC guidelines for maintaining medical electronic products.
Age Temp °C Temp °F
0-2 years 36.4 to 38.0 97.5 to 100.4
3-10 years 36.1 to 37.8 97.0 to 100.0
11-65 years 35.9 to 37.6 96.6 to 99.7
> 65 years 35.8 to 37.5 96.4 to 99.5
Normal Temperatures According To Age

3
Configuration
1. IR Sensor
2. LCD Display
3. Mode Selection
4. Down Button
5. Up Button
6. Mode Button
7. Measurement Trigger
8. Battery Cover
1. Surface Mode Symbol
2. Body Mode Symbol
3. Digital Readout
4. Battery Symbol
5. Log Number
6. Stored Temperatures
7. Temperature °C/°F
8. Buzzer symbol
LCD Screen Indicators
The device is in accordance with Medical Device Directive 93/42/ EEC
The device is in accordance with FCC Part 15 Subpart B: 2007 /Radio Frequency Devices IC Regulation ICEC-00 3:
2004 Interference-causing Equipment Standard - Digital Apparatus
3V DC power supply (2x 1.5v AA Batteries)
Type B Equipment
In order to protect the environment, please recycle the battery according to the local regulations.
Indication of Mode
Attention! Consult accompanying documents.
Description of Symbols

4
Specifications
Display Resolution: 0.1°C (0.1°F)
Operating Temperature: 10°C to 40°C (50°F to 104°F)
Storage Temperature: 0°C to 50°C (32°F to 122°F)
Humidity Rate: ≤ 85%
Power: DC 3V (2x 1.5v AA Batteries)
Size: 149mm x 77mm x 43 mm / 5.9 in x 3in x 1.7 in (L x W x H)
Weight: Gross: 0.88lbs/400g Net: 0.38lbs/172g
In Body Mode: 32°C to 42.5°C (90°F to 108°F)
In Surface Mode: 0°C to 60°C (32°F to 140°F)
Accuracy: ± 0.3°C (0.54°F)
Measuring Distance: 5cm - 15 cm (2in - 5.9in)
Response Time: 0.5 second
32°C to 35.9°C / 93.2°F to 96.6°F: ± 0.3°C/ 0.5°F
36°C to 39°C / 96.8°F to 102.2°F: ± 0.2°C/ 0.4°F
39°C to 42.5°C / 102.2°F to 108.5°F: ± 0.3°C/ 0.5°F
According to ASTM Standard E1965-1998 (2003)
Measurement Range
Non-Contact Body Infrared Thermometer Precision
Use
1. Install batteries.
2. Prior to the first use or when inserting new batteries wait at least 10
minutes for device to warm up.
3. lf use is suspended for a long period, once turned on the device will test
the room temperature and delay start for 1 to 2 seconds.
4. Aim device at the forehead (see the diagram below for the
positioning), from a distance of 5 cm (2 in), press the measuring key;
the temperature is displayed immediately. Ensure there is no hair,
perspiration, cosmetics or clothing covering the forehead.
5. When there is perspiration on the forehead, temperature may also
be taken behind the ear lobe. Ensure there is no hair, perspiration,
cosmetics or clothing covering the area.
Forehead Position Behind the Ear Position

5
Measuring Operation
Choosing the Temperature Scale - F1 Function
Press MODE button for 2 seconds, the screen displays: F1. Select down
for degrees Celsius, up for degrees Fahrenheit.
Alarm Setup - F2 Menu
Press MODE button for 2 seconds. The screen displays: F1. Press MODE
button twice to get F2. Select to increase the threshold by 0.1°C (0.1°F), or
to reduce it by 0.1°C (0.1°F).
Note: The alarm threshold default value is 38°C (100.4°F).
Temperature Reading Adjustment - F3 Menu
To adjust the total variation of the Non-Contact Body Infrared Thermometer,
press MODE button for 2 seconds. The screen displays: F1. Press MODE
button two times to get F3. Select to increase the difference by 0.1°C (0.1
°F), or to reduce it by 0.1°C (0.1 °F). ln the case of seasonal or environmental
changes, verification and adjustment should be completed.
Note: This function is only effective in Body mode.
Buzzer ON/OFF - F4(F3) Menu
Press MODE button for 2 seconds. The screen displays: F1. Press the MODE
button three times to get F4. Select to enable the buzzer (a sound icon “ ”
is displayed on the LCD screen). Press to disable it (the icon disappears).
Exiting the Setting Mode
Press MODE button until the screen turns off.
For First Use and Calibration
For stable and reliable results, it is essential to check the Non-
Contact Body Infrared Thermometer and change as needed,
as follows:
1. Take the temperature of a person using a CLINICAL
THERMOMETER; you will get 37.5°C (99.5°F) for example.
2. Take the temperature of the same person using the Non-Contact
Body Infrared Thermometer keeping the 5 cm to 15 cm (2 in to 5.9
in) distance between the thermometer and the forehead. Take care to
remove any obstacle which could alter the measurement, such as hair,
perspiration, etc. If you get 37.5°C (99.5°F), the Non-Contact Body
Infrared Thermometer is properly set and ready for use. If you get a
lower temperature, 36.4°C (97.4°F) for example, your difference is
1.1°C (2.2°F). You should adjust the temperature on the Non-Contact
Body Infrared Thermometer and add the difference, i.e. 1.1°C (2.2°F).
Press MODE button for 2 seconds, the screen displays F1. Press
MODE button again until you get F3. Press up button in order to add
the difference. For example: 1.1°C - 2.2°F.
3. To check, take the temperature again using the Non-Contact Body
Infrared Thermometer.

6
The Non-Contact Body Infrared Thermometer is designed to take the body
temperature of a human being. Measurement range for Body mode is 32°C to
42.5°C (86°F to108°F). In Surface mode you can also use the Non-Contact
Body Infrared Thermometer to measure the temperature of an area or an
object, a food, a liquid or room temperature. Measurement range for Surface
mode is 0°C to 60°C (32°F to 140°F).
Important: The area temperature differs from the internal body temperature. To
obtain the internal temperature always use the Body mode.
Please make sure to select Body mode for an internal temperature reading and
Surface mode for an external area reading, such as bottle, bath, room, etc.
Data Memory
The device will automatically hold in memory the last 32 temperature
measurements, which will display at the right corner of LCD. Press or
button to display the last temperature measurement. In power off, press
and button together for two seconds, to display the last temperature
measurement. In this mode, change the order number to 0 and press the
MODE button, to delete all memory.
Changing the Batteries
When the LCD screen displays “ ”, the battery is depleted. When changing
the batteries, be careful not to damage the apparatus, which will compromise
the warranty of the device. Never use rechargeable batteries. Use only
single-use batteries. Remove old battery immediately to avoid damage to the
thermometer resulting from battery leakage.
Warranty
The Non-Contact Body Infrared Thermometer was developed for professional
use, and has a limited warranty period of 1 year or 40,000 measurements
against defects in material and workmanship from the date of purchase.
Advice
• The protective glass covering the lens is the most fragile part of the thermometer.
Please take great care to prevent damage.
• Do not use rechargeable batteries.
• Do not place device in fire.
• Do not expose the device to sunlight or water.
• Maintain measuring distance of 5 cm to 15 cm (2 in to 5.9 in).
• Prevent damage to the infrared sensor.
• Clean the device surface with a cotton pad lightly moistened with 70%
Isopropyl alcohol.
• Do not clean with corrosive detergent.
• Keep the device away from water or other liquid.
• Store in a dry environment.
• Keep away from dust and direct sunlight.
Maintenance and Cleaning

7
©2020 DeltaTrak,Inc.
Troubleshooting
Compliance
The following may be used to address common problems. If the problem
persists please contact customer service.
The display shows a temperature lower than 32°C (89.6°F)
In Surface mode, the device will display the surface (external) temperature instead of
the core (internal) body temperature. Switch the device to BODY mode to obtain a
core body temperature measurement.
The screen displays “HI”
The measurement is above the range selected, either
higher than 42.5°C (108 °F) in Body mode or higher
than 60°C (140°F) in Surface mode.
The screen displays “LO”
The measurement is lower than the range selected,
either lower than 32°C (90°F) in Body mode or lower
than 0°C (32°F) in Surface mode.
Reasons LO or HI displayed on screen: Solution:
Temperature reading hampered by
hair, perspiration, cosmetics, etc.
Remove all obstructions prior to taking
temperature.
Temperature hampered by an air flux. Avoid air flux, as this may interfere with
infrared system.
The measuring distance is too far. Maintain a distance of 5 cm to 15 cm
(2 in to 5.9 in).
Device has not acclimated to the
screening room temperature.
Wait 10 minutes and repeat temperature
measurement.
Contact Tech Support at:
Phone: [phone] Ext 5120 Toll Free: 800-390-0804 US & Canada
Email: [email protected]
Troubleshooting, continued
• EN12470-5: European Standard for Clinical Thermometer Performance - Infrared Ear Thermometers
• ASTM E1965-199: ASTM (American Society of Testing and Methodology)-Standard Specification of Infrared
Thermometers for Intermittent Determination of Patient Temperature
• EN 980: Graphical symbols for use in the labeling of medical devices
• EN 1041:Information supplied by the manufacturer with medical devices
• EN 60601-1: Medical electrical equipment Part 1: General requirements for safety (IEC:60601-1 :1998)
• EN 60601-1-2: Medical electrical equipment Part 1-2 : General requirements for safety Collateral standard
Electromagnetic compatibility Requirements and test (IEC 60601-1-2:2001)
EMC Statement
This device has been tested and approved in accordance with EN60601-1-2:2007 for EMC. This does not
guarantee in any way that the device will not be affected by electromagnetic interference. Avoid using the
device in high electromagnetic environments.

5287_20D5
P.O. Box 398 Pleasanton CA 94566
[phone] [phone]
www.deltatrak.com
DeltaTrak Corporate

 Guadalajara, Mexico

 [phone] / 36712190

 www.deltatrakmexico.com
DTI Mexico International

Shenzhen China

[phone]/2837-2741
2837-2664 | 8923-2778
www.deltatrakchina.com.cn
DTI China Limited

NT, Hong Kong

[phone]
www.dtiap.com
DTI Asia Pacific

Auckland, New Zealand

[phone]
www.deltatraksouthpacific.com
DTI South Pacific

Osaka, Japan

[phone]
www.dtijapan.co.jp
DTI Japan Limited

 Antwerp Belgium

 [phone]

 www.deltatrakeurope.be
DTI Europe bvba
DTI South America SA

 Santiago, Chile

 [phone]  [phone]

 www.deltatraksouthamerica.com