Digisol DG-BG1100U User manual

TM
DG-BG1100U
ADSL2/2+ Broadband Router
Quick Installation Guide
V1.1
2010-09-15

FCC Warning
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Copyright © 2010. All rights reserved.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written
consent from the company.
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance could affect the user's authority to operate the equipment.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet from that to which the receiver is
connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits
2
Trademarks:
TM
DIGISOL is a trademark of Smartlink Network Systems Ltd. All other trademarks are
the property of the respective manufacturers.

3
Package Contents
The following items should be present in your package:
Make sure that the package contains above items. If any of the listed items is
damaged or missing, please contact your retailer immediately.
DG-BG1100U ADSL2/2+ Broadband Router
POTS splitter
Switching power adapter (12V DC, 0.5A)
Rubber feet (4 Nos.)
Quick Installation Guide
Installation software CD (includes User Manual & Drivers/Utility)
DIGILINK patch chord (1 No.)
RJ-11 Cable (2 Nos.)
USB Cable (1 No.)
Product Overview
DIGISOL DG-BG1100U ADSL2/2+ Broadband Router is a high-performance router
providing high speed download up to 24Mbps and upload speed up to 1Mbps. The
DG-BG1100U is a combo router providing one RJ-11 interface for ADSL link, one RJ-
45 Ethernet / USB interface for connecting to a notebook/desktop computer. The DG-
BG1100U ADSL2/2+ router can be used for sharing Internet among LAN users by
connecting the Ethernet interface to a switch. The DG-BG1100U is an ideal solution
for SOHO users who wish to share high-speed Internet access.

4
Front View
The DG-BG1100U has one Ethernet/USB interface for connection to a notebook
/desktop computer. The Ethernet interface can be connected to a switch or an Access
Point for sharing the Internet.
System Requirements
The following system requirements are recommended
Notebook or desktop PC with network adapter or USB port.
Windows 2000 / XP / Vista operating system.
Web browser.
AC power socket (100 - 240V, 50/60Hz).

5
Front View
Rear View
USB Driver Installation
LED
Name
Status Description
Off Power is off.
Power On Power is ON and the device operates normally.
Off No signal is detected.
Blink DSL line training is in progress.
Link
On DSL line connection is up.
Data Blink Traffic is in progress.
Off No signal is detected.
Blink User data is going through Ethernet port.
Ethernet
On Ethernet interface is ready to work.
Off No signal is detected.
Blink User data is going through USB port.
USB
On USB interface is ready to work.
After installing the broadband router, you can verify its status from the LED indicators
on the front panel as shown below.
Interface Description
Line RJ-11 port: Connect the router to ADSL connector or splitter
through telephone line.
USB USB device interface for connecting to PC or other network
devices.
Ethernet RJ-45 port, for connecting the router to a PC or other network
devices through Ethernet cable.
Reset
To restore the factory default, keep the device powered ON,
insert a needle into the reset hole and keep the switch inside
pressed for about 1 second.
Power Power interface, for connecting the power adapter.
ON / OFF
Switch Power switch, on the side of power interface.

6
Front View
USB Driver Installation
Connect the USB cable to the USB port on the ADSL router. The cable has two
different type of connectors at two different ends. Connect the appropriate
connector to the USB port of the ADSL router as required.
Connect the other end of the USB cable into the USB port of the PC.
For USB installation on Windows XP, once the PC powers up,a message appears
in the system tray indicating that new hardware is found.
To connect the ADSL router to the USB port of PC, perform the following steps:
Then, the ‘Found New Hardware Wizard’ dialog box pops up. Select ‘Install the
software automatically (Recommended)’ and insert the driver CD in the CD-ROM of
the computer. Click ‘Next’. The system searches CD-ROM for the best USB driver.
Then you can install the USB driver according to the instructions

7
Router Installation
Insert the Software Installation CD provided with your DG-BG1100U in the CD-
ROM of your computer. The following screen will appear. To get more
information on configuration of router click ‘User manual’, else click ‘Start’ to
proceed with the router configuration.
To install the router using the utility provided with Software Installation CD,
assign a static IP address to your notebook/desktop computer in the subnet
192.168.1.X. For example, assign the IP address 192.168.1.10, subnet mask
255.255.255.0 and default gateway 192.168.1.1.
Connect the routers line port to the modem port of the ADSL splitter using the
RJ-11 cable, then click ‘Next’, to continue with the configuration.

8
Power ON the router, then click ‘Next’, to continue with the configuration.
Connect one end of the RJ-45 Ethernet cable to Ethernet port on the router and the
other end to the LAN card of your system, then click ‘Next’, to continue with the
configuration.

9
In the following screen, you can view the description of LED indicators. Click ‘Next’ to
continue with the configuration.
The Quick Setup Utility will try to detect the router. This may take some time to detect
the router.

10
Once the router is detected by the utility, we will get the following screen. Here you
can configure the ADSL settings essential for Internet connection, then click ‘Next’ to
continue.
Select the country and service provider from the drop-down list. You can change the
default VPI/VCI as instructed by your ISP.
VPI : The valid value is in the range of 0 to 255.
VCI : The valid value is in the range of 32 to 65535. (0 to 31 is reserved for local
management of ATM traffic

11
You can select the encapsulation mode from the drop-down list.
MER : If you select MER as the network protocol, the router obtains an IP address
automatically.
IPoA : If you select IPoA as the network protocol, you cannot use the DHCP
service. You need to enter the IP address, subnet mask, default gateway and DNS
as provided by your ISP.
Select the protocol for WAN interface, then click ‘Next’, to continue with the
configuration.
Bridging : If you select Bridging as the network protocol, you must use a third
party Dial-up software or Windows New Connection Wizard to configure the
Internet dial-up access.
PPPoE or PPPoA: If you select PPPoE or PPPoA as the network protocol, then
you must know the username and password provided by your service provider.

12
If you select the ‘Connect on Demand’ check box and enter the time, the router will
disconnect from internet automatically if it was not in use for the specified ‘Max Idle
Time’. When you want to use Internet, the router will connect to the Internet
automatically. You can save traffic flow using this service.
If you select the WAN protocol as PPPoE or PPPoA then we will get the following
screen. In this page enter the correct username and password provided by your
Internet service provider, then click ‘Next’ to continue.
The following screen appears when the utility saves the settings permanently to the
router.

13
The following screen gives details about the running status of the router.
Note: If the IP address appears 0.0.0.0, then click Refresh button to retry the
connection to Internet. If a valid IP address appears, other than 0.0.0.0, then
click ‘Finish’ to complete the configuration.
Congratulations! Your router configuration is now finished.

14
Following screen will appear on successful Login. You can now configure the router
through this web management page.
To access the web management of the router, assign a static IP address to your
notebook/desktop computer in the subnet 192.168.1.X. For example, assign the IP
address 192.168.1.10, subnet mask 255.255.255.0 and default gateway
192.168.1.1
Open a web browser and enter “http://192.168.1.1” in the address bar, press ‘Enter’.
A login screen will appear, assign username as “admin” and password as “admin”.
Press ‘OK’ to Log in.
Web management of the router

15
Following are the solutions to problems that may occur during the installation and
operation of the DIGISOL DG-BG1100U Broadband Router.
This product comes with Lifetime Warranty. For further details about warranty policy
and Product Registration, please visit support section of www.digisol.com
FAQ
1. Why all the LED indicators on router are off?
Verify the connection between the power adaptor and the power socket.
Verify the status of the power switch.
2. Why the Ethernet LED indicator is off?
Verify the connection between the ADSL router and your computer, hub, or switch.
Verify whether the PC, hub, or switch are turned ON.
3. Why the Link LED indicator is off?
Verify the connection between the “Line” port of router and the wall jack.
4. Why Internet access fails even if the Link LED indicator is on?
Verify whether the VPI, VCI, user name, and password are correctly entered.
5. Why does the web configuration page of the router fail to be accessed?
Choose Start > Run from the desktop, and ping 192.168.1.1 (IP address of the
router). If the router cannot be reached, check the type of the network cable, the
connection between the router and the PC, and the TCP/IP configuration of the PC.
6. How to load the default settings after incorrect configuration?
To restore the factory default, keep the device powered on; push a needle into the
hole for about 3 seconds, and then release. The default IP address and subnet
mask of the router are 192.168.1.1 and 255.255.255.0 respectively.
- User/password of super user: admin/admin.
- User/password of common user: user/user

1800-209-3444 (Toll Free)
[email protected] [email protected] www.digisol.com