Digital Projection Titan 800 3D series User manual

Rev A June 2012
USER GUIDES
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
113-083A
Titan 800 3D series
High Brightness Digital Video Projector
BOOK CONTENTS
About these Guides
Symbols used in these guides
Warnings
Notes
Product revision

Digital Projection Titan 800 3D series ABOUT THESE GUIDES
Rev A June 2012
About these Guides
Please read this guide carefully before using the projector, and keep it handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in these guides
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
Notes
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice. Projectors built prior to this revision of the Operating Guide may therefore not include all the features described.

Rev A June 2012
Titan 800 3D series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
BOOK CONTENTS
INSTALLATION AND QUICK-
START GUIDE
What’s in the Box?
Getting to Know the Projector
Front and rear views
Remote control
Control panel indicators
Connection panel indicators

Digital Projection Titan 800 3D series CONTENTS Installation and Quick-Start Guide
Rev A June 2012
CONTENTS
What’s in the Box?...............................................................................Inst_1
Getting to Know the Projector....................................................Inst_2
Front and rear views .............................................................................Inst_2
Remote control......................................................................................Inst_2
Control panel indicators.......................................................................Inst_3
Connection panel indicators................................................................Inst_3
Positioning the Screen and Projector....................................Inst_4
Chassis adjustment ..............................................................................Inst_4
Fitting and adjusting the optional Rigging Frame .............................Inst_4
Fitting the Lens .....................................................................................Inst_5
Operating the Projector...................................................................Inst_6
Switching the Projector On ..................................................................Inst_6
Selecting an Input Signal or Test Pattern ...........................................Inst_6
Input signal....................................................................................Inst_6
Test pattern ...................................................................................Inst_6
Adjusting the Lens and Image .............................................................Inst_7
Zoom.............................................................................................Inst_7
Focus ............................................................................................Inst_7
Shift...............................................................................................Inst_7
Picture...........................................................................................Inst_7
Switching the Projector Off..................................................................Inst_7

Digital Projection Titan 800 3D series WHAT'S IN THE BOX? Installation and Quick-Start Guide
Page Inst_1Rev A June 2012
What’s in the Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your Projector.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(105-023)
4x AAA batteries
User Guides on CD
(112-659) Important Information
(112-658)
Power cable, United Kingdom
(112-000)
Power cable, Europe
(112-001)
Power cable, North America
(112-002)
Projector
Remote cable
(102-162)

Digital Projection Titan 800 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Page Inst_2Rev A June 2012
Getting to Know the Projector
Front and rear views
Notes
The projector uses the standard
Digital Projection infra-red remote
control.
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Lens
Air
outlets
Air
inlets
Side
Connection
panel
Mains
input
Control
panel
Adjustable
feet
Front
infra-red
window
Rear
infra-red
window
(on
connection
panel)
Remote control
Infra-red
reception
40°
40°
Transmit
indicator
Remote
control
backlight
On/Off
Rear
Connection
panel
Air lters
(behind panel)

Digital Projection Titan 800 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Page Inst_3Rev A June 2012
Control panel indicators
The indicators on the control panel are as follows:
Power off = NO POWER
green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Notes
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
For more information about
the connection panels, see the
Connection Guide.
Connection panel indicators
The indicators on the rear connection panel are as follows:
All on = Power-On Self Test
Lamps 1-2 off = OFF
green = ON (100%) amber = (80 - 99%)
ashing green = WARM-UP ashing amber = COOL-DOWN
red (projector in standby) = Lamp Comms Error (call service)
red (projector on) = Ballast Comms Error (call service)
ashing red (projector in standby) = Lamp Error on previous operation
ashing red (projector on) = Lamp / Interlock Error
Error ashing = Fan / System Error steady = Voltage Error
IR blue ash = Remote control command received
Inputs The indicators next to the input connectors on both panels are as follows:
off = not selected
green = input selected, signal detected, and in range
ashing green = input selected, but signal not detected or out of range
Power Shutter
Lamps
1 2
Error
IR
Rear Connection Panel Side Connection Panel

Digital Projection Titan 800 3D series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Page Inst_4Rev A June 2012
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least
30cm (12in) of space between the
ventilation outlets and any wall,
and 10cm (4in) on all other sides.
Do not stack more than 3
projectors.
Do not place heavy objects on top
of the projector chassis. Only the
chassis corners and the rigging
frame are capable of withstanding
the weight of another projector.
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
Backup safety chains or wires
should always be used with
ceiling mount installations.
Do not tilt the projector more
than ±12° in either direction, in
desktop or ceiling mode, when in
use, as this may cause serious
lamp failure, damage the lamp
module and cause extra cost on
replacement.
±12°±12°
±12°±12° Ceiling
Desktop
Positioning the Screen and Projector
• Install the screen, ensuring that it is in the best position for viewing by your audience.
• Position the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen.
Chassis adjustment
• If the projector is to be operated from a at surface such as a projector table, then adjustment of projector level should be made by
turning the four feet under the chassis. Set the adjustable feet so that the projector is level, and perpendicular to the sceen.
Fitting and adjusting the optional Rigging Frame
• Remove the four adjustable feet.
• Secure the rigging frame to the projector, as shown below, making sure that the cable
attachments are at the top. Three screws secure each of the adjuster brackets to a
corner handle.
• To adjust the pitch, turn either the front pair or the rear pair of vertical adjusters, taking
care to turn both adjusters by the same amount.
• To adjust the roll, turn either the left pair or the right pair of vertical adjusters, taking care
to turn both adjusters by the same amount.
• To adjust the yaw, turn the single horizontal adjuster at the front.
Fixing
screws
Pitch Roll Yaw
Horizontal
adjuster
Vertical
adjusters
Frame
couplings

Digital Projection Titan 800 3D series FITTING THE LENS Installation and Quick-Start Guide
Page Inst_5Rev A June 2012
Fitting the Lens
• Turn the lens release lever clockwise so
that it is pointing upwards, to open the
lock fully.
• Remove the rear lens cap from the lens.
• Insert the lens into the lens aperture,
making sure that the plug on the zoom
drive mechanism lines up with the
socket on the front of the projector, then
push the lens in rmly as far as it will go.
Notes
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
The lens release lever should
always be set to the locked
position to prevent the lens from
falling out.
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
Lens
release
lever
• Turn the lens release lever anti-
clockwise to the mid-position.
• The lens can now be pushed in further.
Push the lens in rmly as far as it will
go.
• Turn the lens release lever fully
anti-clockwise so that it is pointing
downwards, to close the lock fully.

Digital Projection Titan 800 3D series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Page Inst_6Rev A June 2012
Operating the Projector
Switching the Projector On
• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
• Wait until the self-test has completed and the standby indicator on the projector control panel shows amber. The lamp will be off and the
projector will be in STANDBY mode.
• Press on the remote control or the control panel and hold for 3 seconds, to switch the projector ON. The power indicator on the
control panel will show green, the lamp will light and the shutter will open.
Selecting an Input Signal or Test Pattern
Input signal
• Connect an image source to the projector. The signal should be automatically detected by the
projector, and should be displayed within a two or three seconds.
If more than one signal is connected, then select the image you want to display:
• Press one of the Input buttons, to on the remote control, or
• Open the Main Menu, by pressing .
• Select from the Input Selection menu, using the and buttons.
Test pattern
If you have no image source connected to the projector, then you can display a test pattern instead:
• Open the Main Menu, by pressing .
• Select Test Pattern from the Input Selection menu, using the and buttons.
• Select a pattern from the Test Pattern menu, using the and buttons.
• Close the Main Menu, by pressing again.
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.