Dimplex SOLCU3 User manual

SOLARTHERMIE - SOLAR THERMAL - SOLAR TÉRMICO - SOLAIRE THERMIQUE - SOLARE TERMICO
Installation and operating instructions
Temperature difference controller
6 inputs, 3 outputs,
integrated data logger for SD card
730.137 | Z01 | Subject to change due to technical improvements! | ST0043_A - 09/08
EN
These operating instructions are part of the product.
Read these operating instructions carefully before use,
keep them over the entire lifetime of the product,
and pass them on to any future owner or user of this product.



Solar Controller SOLCU3

2730.137 | 08.37
EN
Contents
1 Safety....................................................................................4
1.1 Proper usage............................................................................ 4
1.2 Dangers during assembly and commissioning......................... 4
1.3 Detecting faults ....................................................................... 5
1.4 Hot water temperature............................................................ 5
1.5 Disposal ................................................................................... 5
1.6 Exclusion of liability ................................................................. 5
2 Case overview ......................................................................6
3 About this manual ...............................................................7
3.1 Applicability ............................................................................. 7
3.2 Users ........................................................................................ 7
3.3 Description of symbols ............................................................7
4 Installation ..........................................................................8
4.1 Opening/closing the housing...................................................8
4.2 Assembly.................................................................................. 9
4.3 Electrical connection.............................................................. 10
4.4 Dismantling............................................................................ 11
4.5 Terminal diagram .................................................................. 12
5 Commissioning...................................................................16
5.1 Setting the language ............................................................16
5.2 Setting the time and date...................................................... 16
5.3 Setting the automatic summer time......................................16
5.4 Setting the system group................................................17
5.5 Setting the system .................................................................17
6 Modes of operation ...........................................................18
6.1 "OFF" mode ............................................................................ 18
6.2 "Automatic" mode.................................................................. 18
6.3 "Manual" mode ...................................................................... 18
7 Settings...............................................................................19
7.1 Time/date............................................................................... 19
7.2 Systems.................................................................................. 22
7.3 Functions ............................................................................... 62
7.4 Parameters............................................................................. 81
7.5 Storage priority...................................................................... 83
7.6 Language............................................................................... 84
7.7 Factory settings...................................................................... 84
7.8 Set season ............................................................................. 84

3
730.137 | 08.37
EN
8 Automatic mode ................................................................85
8.1 Status display......................................................................... 86
8.2 Temperature sensor min/max display..................................... 86
8.3 Operating hours display for pumps and switching valves .....86
9 Data logger.........................................................................87
9.1 Handling the SD card.............................................................87
9.2 Display screen ........................................................................ 87
9.3 Formating .............................................................................. 88
9.4 Data evaluation...................................................................... 89
10 Service ................................................................................90
11 Fault finding.......................................................................90
11.1 Causes of problems ...............................................................90
11.2 Pt1000 temperature sensor values.........................................92
12 Information windows ........................................................93
13 Plausibility indices..............................................................97
14 Technical data.....................................................................99
14.1 Performance data .................................................................. 99
14.2 Parameter settings...............................................................100
14.3 Parameter values for functions ...........................................102
15 Notes ................................................................................107
Product information
EC declaration of conformity
"This product conforms to the applicable European directives with
regard to its design and its operating behaviour. This conformity has
been verified. Further information in this regard can be obtained from
your dealer."

4730.137 | 08.37
EN
1 Safety
1.1 Proper usage
The temperature difference controller (hereinafter referred to as controller) is an independently installed
electronic temperature controller for on-surface installation, and may only be used for controlling solar
thermal systems within the permissible ambient conditions (see chapter 15 "Technical data").
The controller must not be operated in the following environments:
outdoors
in damp rooms
in rooms where highly flammable gas mixtures can occur
in rooms in which the operation of electrical and electronic components may cause dangers to arise
1.2 Dangers during assembly and commissioning
The following dangers exist during installation/commissioning of the controller and during operation (in
case of installation errors):
risk of death by electrocution
risk of fire due to short-circuit
damage to any of the constructional fire safety measures present in the building due to incorrectly
installed cables
damage to the controller and the connected devices due to improper ambient conditions, inappropri-
ate power supply and the connection of prohibited devices, faulty devices, or devices not included in
the device specifications, as well as incorrect assembly or installation
NOTE
Observe the controller's type plate!
Therefore, all safety regulations apply when working on the mains supply. Only electricians may perform
work that requires opening the controller (such as electrical connection work).
When laying cables, ensure that no damage occurs to any of the constructional fire safety measures
present in the building.
Make sure that the permissible ambient conditions at the installation site are not exceeded (see chap-
ter 15 "Technical data").
Be sure to comply with the specified ingress protection.
Labels and markings applied in the factory may not be altered, removed or rendered unreadable.
Before connecting the device, make sure that the power supply matches the specifications on the type
plate.
Make sure that all devices which are connected to the controller conform to the technical data of the
controller.
Secure the device against unintentional start-up.
All work on an open controller must be performed with the mains supply removed.
Protect the controller against overloading and short-circuiting.
•
•
•
•
•
•
•
•










5
730.137 | 08.37
EN
1.3 Detecting faults
Check the display regularly.
In case of faults, isolate the cause (see chapter 11.1 "Causes of problems").
As soon as it becomes evident that safe operation is no longer guaranteed (e.g. visible damage),
remove the device from the mains supply immediately.
Have trained professional personnel remedy the fault.
1.4 Hot water temperature
In order to limit the hot water temperature to 60 °C at the outlets, a hot water mixer must be installed.
1.5 Disposal
Dispose of the controller in accordance with the regional regulations.
1.6 Exclusion of liability
The manufacturer can neither monitor the compliance with this manual nor the conditions and methods
during the installation, operation, usage and maintenance of the controller. Improper installation of the
system may result in damage to property and, as a result, to bodily injury.
Therefore, the manufacturer assumes no responsibility and liability for loss, damage or costs which result
from or are in any way related to incorrect installation, improper operation, incorrect execution of installa-
tion work and incorrect usage and maintenance.
Similarly, we assume no responsibility for patent right or other right infringements of third parties caused
by usage of this controller.
The manufacturer reserves the right to make changes to the product, technical data or installation and
operating instructions without prior notice.






6730.137 | 08.37
EN
2 Case overview
Automatic
Manual
Off
Fuses
(see chapter 15)
Replacement fuses
(see chapter 15)
Power connection
Outputs Inputs RS232 and RS485 interface,
alarm output,
Direct Sensor output
Strain relief
Operating buttons
Arrow up
for scrolling up through the menus
SET button
confirmation or activation of a value
ESC button
escape key
Arrow down
for scrolling down through the menus
Display
Display for controller operation
and system settings
Operating switch
The following modes of operation
can be selected:
- Manual
for commissioning
and testing for function
- Automatic
for automatic operation
- Off
for switching off
the outputs
SD card

7
730.137 | 08.37
EN
3 About this manual
3.1 Applicability
This manual describes the installation, commissioning, operation, maintenance and dismantling of the
temperature differential controller for solar thermal energy systems. When installing the remaining compo-
nents, e.g. solar collectors, pump assemblies, storage units, pumps and switching valves, be sure to observe
the appropriate installation instructions provided by each manufacturer.
3.2 Users
Installation, commissioning, maintenance and dismantling of the controller may only be performed by
trained professional personnel. Before commissioning, the controller must be professionally assembled and
installed by professional personnel in accordance with the applicable regional and transregional regulations
as well as the safety instructions and general instructions within these installation and operating instruc-
tions. The professional personnel must be familiar with these operating instructions.
The controller is maintenance-free.
Use the controller only after first thoroughly reading and understanding these operating instructions and
the safety instructions. Adhere to all safety instructions and consult professional personnel in the event of
any ambiguities.
This device is not intended for persons (or children) with physical, sensory, or mental disabilities, or who
have inadequate experience and knowledge, unless they are instructed in the use of the device, and initially
supervised, by a person responsible for their safety. Children should not be left alone with the device, to
ensure that they do not play with it.
3.3 Description of symbols
3.3.1 The structure of the warning notices
SIGNAL WORD
Type, source and consequences of the danger!
Measures for avoiding danger.
3.3.2 Danger levels in warning notices
Danger level Likelihood of occurrence Consequences resulting
from non-compliance
DANGER Imminent threat of danger Death, serious bodily injury
WARNING Possible threat of danger Death, serious bodily injury
CAUTION Possible threat of danger Minor bodily injury
CAUTION Possible threat of danger Property damage
3.3.3 Note
NOTE
Note on easier and safer working habits.
Measures for easier and safer working habits.



8730.137 | 08.37
EN
3.3.4 Other symbols and markings
Symbol Meaning
✓Condition for action
Call to action
Result of action
• List
Emphasis on
issue at hand Emphasis on issue at hand
:Press „Arrow up/down“ for scrolling.
:Press „Arrow down“ for scrolling through the
menu or to adjust a value.
:Press „Arrow up“ for scrolling through the menu
or to adjust a value.
SET: Press „SET“ button to confirm or activate a value.
ESC: Press „ESC“ button to cancel.
4 Installation
4.1 Opening/closing the housing
DANGER
Risk of death by electrocution!
Remove the controller from the power supply before opening the case.
Make sure that the power supply cannot be unintentionally switched
back on.
Do not damage the case.
Only switch the power supply back on after the case has been closed.
The upper case is connected to the lower case by two latches, and fas-
tened with a screw.
4.1.1 Opening the case
Loosen the screw and remove the upper case in an upwards direc-
tion.
4.1.2 Closing the case
Place the upper case over the lower case at an angle. Insert the
latches into the recesses of the lower case.
Pivot the upper case down and feed the operating buttons through
the matching holes.
Fasten the case tightly with the screw.
Operating buttons
Upper casing
Screw
Lower case
Latch









9
730.137 | 08.37
EN
4.2 Assembly
WARNING
Risk of electrical shock and fire if mounted in a damp environ-
ment!
Only mount the controller in an area where the ingress protection is
sufficient (see chapter 15 "Technical data").
4.2.1 Mounting the controller
CAUTION
Risk of injury and damage to the case when drilling!
Do not use the case as a drilling template.
Choose a suitable installation site.
Drill the upper fastening hole.
Screw in the screw.
Remove the upper case.
Hang the case in the recess .
Mark the position of the lower fastening holes ,.
Remove the case again.
Drill the lower fastening holes.
Hang the case in recess .
Screw the case firmly using the lower fastening holes and .
Mount the upper case.














10 730.137 | 08.37
EN
4.3 Electrical connection
DANGER
Risk of death by electrocution!
Remove the controller from the power supply before opening the
case.
Observe all applicable legal guidelines and regulations of the local
electricity supplier.
NOTE
The device is to be connected to the mains by means of a plug with
grounding contact, or in the case of a fixed electrical installation, via a
disconnection device for complete disconnection in accordance with the
installation guidelines.
4.3.1 Preparing the cable feed
Depending on how the controller is mounted, the cables may enter the
device through the rear of the case or the lower side of the case.
565
44
Feeding the cable through the rear of the case:
Remove the plastic flaps from the rear side of the case using an
appropriate tool.
WARNING
Risk of electrical shock and fire due to cables coming loose!
Install an external strain relief for the cables.
Feeding the cable through the lower side of the case:
Use an appropriate tool to cut the plastic flaps at the left and the
right and break them out of the case.
Fasten cable at position with the provided plastic links.







11
730.137 | 08.37
EN
4.3.2 Connecting the cables
If a protective conductor is provided or required for pumps/valves,
connect it to the corresponding terminals of the controller. When
connecting the protective conductor, observe the following points:
Make sure that the protective conductor is also connected to the
controller's mains supply side.
Each terminal may only be connected to a single connecting wire
(max 2.5 mm2).
The terminal screws are approved for connection of cables as fol-
lows:
single wire (solid): ≤ 2.5 mm²
fine strand (with core end sleeves): ≤ 1.5 mm²
Only use the original temperature sensors (Pt1000) that are
approved for use with the controller.
Observe the following points:
The polarity of the temperature sensor contacts is not important.
Do not lay sensor cables close to power cables
(minimum separation: 100 mm).
If inductive effects are expected, e.g. from power cables,
overhead wires, transformer substations, radio and television
devices, amateur radio stations, microwave devices, etc., the
sensor cables must be adequately screened.
Sensor cables may be extended to a maximum length of 100 m.
If adding extensions to sensor cables, select the following cable
cross sections:
0.75 mm2up to 50 m long
1.5 mm2up to 100 m long
Connect the cables in accordance with the terminal diagram
(see chapters 4.5 and 7.2)
4.4 Dismantling
DANGER
Risk of death by electrocution!
Remove the controller from the power supply before dismantling it.
To dismantle the controller, follow the assembly instructions in the
reverse order.

-
-

-
-


-
-
-
-

-
-




12 730.137 | 08.37
EN
4.5 Terminal diagram
4.5.1 Power connection
Please refer to the type plate on the case to determine the type of
power supply required
The protective conductor must be connected
Cables conforming to at least type H05 VV-... (NYM…) must be used
N L N R1 N R2 N n.c n.c. R3
n.c. L L n.c. n.c. X
G1
D1
230 V ~ 115 V ~
4.5.2 Connection of the inputs
Inputs 1 - 5: for Pt1000 temperature sensor
Input 6: for Pt1000 temperature sensor or pulse generator for
recording volume flow (measuring heat quantities)
1 2 3 4 5
T1
T2
T3
T4
T6 *)
E1 E2 E3 E4 E5 E6
6
T5
•
•
•
•
•
G1: grid
D1: wire bridge
E1: input 1
E2: input 2
E3: input 3
E4: input 4
E5: input 5
E6: input 6
T6 *): T6 or pulse generator

13
730.137 | 08.37
EN
Inputs 1 - 5: temperature recording
Inputs
T1...T5
Temperature sensor Pt 1000
(polarity irrelevant)
1...5
ϑ
Input 6: recording temperatures and pulse values
T6
Pt1000 temperature
sensor
(polarity irrelevant)
Standard:
volume flow recording
(polarity irrelevant)
Special case:
volume flow recording
(observe polarity,
pulse signals up to max.
600 Hz)
Temperature
recording
Recording pulse values
via reed relay Recording pulse values via open collector
6
ϑ
66

14 730.137 | 08.37
EN
4.5.3 Connection of outputs R1, R2 and R3
Outputs R1 and R2:
Semiconductor relays (TRIAC), also suitable for RPM control; max.
switching current: see type plate
CAUTION
Avoiding damage and malfunctions
When connecting an external relay or contactor, or when connect-
ing a pump which has its own electronic RPM control, the controller
output's RPM control must be deactivated (see chapter 7.4.3 "Setting
the RPM control parameters").
N R1 N R2 N n.c n.c. R3
n.c. L L n.c. n.c. X
R1 R3
D1
R1 R2
R2
Output R3: switched output or potential-free
output
230 VAC switched output (option: 115 VAC) via electromechanical
relay; max. switching current: see type plate; wire bridge must be
connected!
R3
n.c.
X
N R1 N R2 N n.c
n.c.
n.c. L L n.c.
R1 R2 R3
D1
R3
•

•
R1: output 1
R2: output 2
R3: output 3
D1: wire bridge
R1: output 1
R2: output 2
R3: output 3
D1: wire bridge

15
730.137 | 08.37
EN
Potential-free output via electromechanical relay; wire bridge must
be removed!
DANGER
Risk of death by electrocution!
In the event of use as a potential-free output, it must be ensured that
the connections cannot come into contact with the mains voltage.
N R1 N R2 N n.c n.c. R3
n.c. L L n.c. n.c. X
R1 R3
R3
R2
4.5.4 RS232 and RS485 interface, alarm output, and
Direct Sensor input
RS232 interface
A B Rx Tx
TQ
+ 5V
T
T
T
T
T
TQ
+ 5V
T
A B Rx Tx
T
T
1 2 3 4 5
6 7 8 9
A B Rx Tx
A B Rx Tx
TQ
+ 5V
T
T
T
T
T
TQ
+ 5V
T
A B Rx Tx
T
T
1 2 3 4 5
6 7 8 9
A B Rx Tx
A B Rx Tx
TQ
+ 5V
T
T
T
T
T
TQ
+ 5V
T
A B Rx Tx
T
T
1 2 3 4 5
6 7 8 9
A B Rx Tx
Direct Sensor
(observe the manufacturer’s
specifications)
Alarm output, see chapter 15
D - Sub
9-pin socket
(solder side)
A B Rx Tx
TQ
+ 5V
T
T
T
T
T
TQ
+ 5V
T
A B Rx Tx
T
T
1 2 3 4 5
6 7 8 9
A B Rx Tx
RS485 interface
•

R1: output 1
R2: output 2
R3: output 3

16 730.137 | 08.37
EN
5 Commissioning
Make sure that the installation is finished completely and correctly,
and that the switch on the controller is set to "OFF".
The display for setting the language appears.
5.1 Setting the language
"Deutsch" flashes in the display.
:select a language.
SET: confirm the language.
ESC: finish the settings.
The display for setting the time appears.
5.2 Setting the time and date
"12:00" flashes in the display.
: set the hours.
SET: confirm the hours.
The minutes display flashes.
: set the minutes.
SET: confirm the minutes.
The year flashes.
: set the year.
SET: confirm the year.
The month flashes.
: set the month.
SET: confirm the month.
The day flashes.
: set the day.
SET: confirm the day.
ESC: finish the settings.
Display for activating the "automatic summer time change-over"
appears.
5.3 Setting the automatic summer time
Display for "automatic summer time change-over" appears.
NOTE
The controller can also be operated without activating the "automatic
summer time change-over".
SET: press button.
"automatic summer time change-over" is activated.
ESC: finish the settings.
The display for setting the system group appears.


✓




✓
















✓





[..........]
Display: 6.1
[Deutsch]
[..........]
Display: 6.1
[Deutsch]



Display: 1.1


Display: 1.1
 Automatic
summer time
change-over
(for EU)
Automatic
summer time
change-over
(for EU)


17
730.137 | 08.37
EN
5.4 Setting the system group
NOTE
For an overview of systems, see chapter 7.2 "Systems".
The first system group (1 storage tank system) appears in the
display.
:select a system group.
SET: confirm the system group.
The display for setting the system appears.
5.5 Setting the system
The first system in the selected system group appears in the display.
:selecting a system.
SET: confirm the system.
In the display, a small checkmark appears below the item
number, which confirms that the system is selected.
ESC: exit the settings menu.
The commissioning is finished.
✓



✓






>@

Display: 2.1
[Storage tank]
>@

Display: 2.1
[Storage tank]
Display: 2.1.1Display: 2.1.1


18 730.137 | 08.37
EN
6 Modes of operation
6.1 "OFF" mode
In order to switch off the outputs, slide the operating switch down.
A new window appears in the display, which shows "OFF", as
well as the controller software version number and the number
of the chosen system. The display is lit with a red background.
In "OFF" mode, all outputs (R1, R2, R3) are switched off.
NOTE
On delivery from the manufacturer, the switch is set to "OFF".
6.2 "Automatic" mode
CAUTION
Damage to pump caused by dry operation!
The controller may only be set to "Automatic" when the system has been
filled.
In order to switch the outputs to "Automatic", slide the operating
switch to the middle position.
The status appears in the display.
This mode of operation is the automatic controller mode and must be
set for automatic operation.
NOTE
During normal system operation, the operating switch should always
be set to "Automatic".
6.3 "Manual" mode
CAUTION
Damage to pump caused by dry operation!
The controller may only be set to "Manual" when the system has been
filled.
When operating the device for the first time, or when testing the func-
tion, the controller outputs can be manually switched.
In order to switch the outputs manually, slide the operating switch up.
The display is backlit in red and a settings window is displayed.
:selecting an output.
SET: switch the selected output to "on" or "off".
ESC: close the settings window.
The current recorded values can now also be queried for the
purpose of checking.
:access measured values.
SET: reopen the settings window.














2))
9HUVLRQ;;
6\VWHP1R;


off
2))
9HUVLRQ;;
6\VWHP1R;


off

&



Automatic
&



Automatic

5ĺRQ
5RII
5RII

Manual

5ĺRQ
5RII
5RII

Manual


19
730.137 | 08.37
EN
7 Settings
Menu overview, see following double page
7.1 Time/date
The time and date can be displayed and adjusted via the "Time/Date"
menu item. The automatic summer time change-over can still be acti-
vated or deactivated.
7.1.1 Setting the time and date
SET: press button for approx. 2 sec.
The "Time" menu item is displayed.
SET: press button.
The current time is displayed.
SET: press button to confirm.
The hours display flashes after confirmation of the time.
:set the hours.
SET: press button to confirm.
The minutes display flashes after confirmation of the hours.
:set the minutes.
SET: press button to confirm.
The year display flashes after confirmation of the minutes.
:set the year.
SET: press button to confirm.
The month display flashes after confirmation of the year.
:set the month.
SET: press button to confirm.
The day display flashes after confirmation of the month.
:set the day.
SET: confirm the time and date.
7.1.2 Activating the automatic summer time
change-over
:press button.
The display for “Automatic summer time change-over (for EU)”
appears.
SET:
press to activate or deactivate the automatic summer time
change-over.
A cross in the control box shows that the automatic summer
time change-over is active.
ESC: exit the "automatic summer time change-over" submenu.
ESC: exit the "Time/Date" menu item.
NOTE
The controller can also be operated without activating the "automatic
summer time change-over".


























>@
Display: 1
[Time/date]
>@
Display: 1
[Time/date]




Display: 1.1


Display: 1.1

Automatic
summer time
change-over
(for EU)
Automatic
summer time
change-over
(for EU)


20 730.137 | 08.37
EN
Menu overview
ESCSETSETSET 2 sec
Status display
Time Systems
1 storage tank
systems
2 storage tanks
systems
3 storage tanks
systems
System 1
System 2
System 3
System 4
System 5
System 12
System 13
System 21
System 22
Storage priority Language Factory
settings
ESCSETSETSET 2 sec
Functions
Circulation
Back-up heating
Solid fuel boiler
Quick charge
Bypass
Heat quantity
Thermostat
Difference
thermostat
Time function
Interval
Stagnation
reduction
Holiday/recooling
function
Frost protection
Anti-legionella
function
Display storage
tank top
Data logger
Alarm output
Max. temperature
storage tank 2
Switch-on temp.
difference solar 1
Switch-off temp.
difference solar 1
Switch-off temp.
difference solar 2
Max. collector
temperature
Min. collector
temperature
Switch-on tempera-
ture difference
return increase
Switch-off tempera-
ture difference
return increase
Max. temperature
loading circuit 1
Min. temperature
loading circuit 1
Loading strategy
storage tank 3
RPM control
pump R1
Max. temperature
storage tank 3
Max. temperature
swimming pool
Switch-on temp.
difference solar 2
Max. temperature
loading circuit 2
Min. temperature
loading circuit 2
Loading strategy
storage tank 1
Loading strategy
storage tank 2
RPM control
pump R2
Max. temperature
storage tank 1
Parameters
System 6
System 7
System 8
System 9
System 10
System 11
System 14
System 15
System 16
System 17
System 18
System 19
System 20
2 storage tanks swim-
ming pool systems
System 33
System 34
Swimming pool
systems
System 23
System 24
Storage tank swim-
ming pool systems
System 29
System 30
Seasonal systems
System 35
System 36
System 37
System 38
Set season
The menu item“Set
season”is only
displayed if a
seasonal system
has been selected.
System 25
System 26
System 27
System 28
System 31
System 32
System 39
System 40