Dinstar MTG600 User manual

MTG600 Trunk Gateway User Manual V2.0
Dinstar Technologies Co., Ltd.

MTG600 User Manual
Revision Records
File Name
MTG600 trunk gateway user manual
Document Version
2.0
Firmware Version
2.02.02.01
Date
03/05/2012
Revised by
Technical Support Department

MTG600 User Manual
Content
1. Product Introduction.....................................................................................................................1
1.1 Overview.............................................................................................................................1
1.2 Equipment Structure ...........................................................................................................2
1.2.1 Rear View .................................................................................................................2
1.2.2 Front View................................................................................................................3
1.2.3 RJ-48c Line sequence ..............................................................................................4
1.3 Functions and Features .......................................................................................................4
1.3.1 Protocol standard supported....................................................................................4
1.3.2 System Function .......................................................................................................4
1.3.3 Industrial standards supported ................................................................................4
1.3.4 General hardware specification ...............................................................................5
2. Parameter Setting..........................................................................................................................6
2.1 Login...................................................................................................................................6
2.2 Web interface structure and navigation tree ......................................................................7
2.3 Status & Statistics................................................................................................................9
2.3.1 System Information ..................................................................................................9
2.3.2 E1/T1 Status...........................................................................................................11
2.3.3 PSTN Trunk Status.................................................................................................12
2.3.4 IP Trunk Status.......................................................................................................12
2.3.5 PRI Call Statistics...................................................................................................13
2.3.6 SS7 Trunk Call Statistics........................................................................................14
2.3.7 SIP Call Statistics...................................................................................................14
2.4 Network.............................................................................................................................15
2.5 PRI Config ........................................................................................................................15
2.5.1 PRI Parameter.........................................................................................................16
2.5.2 PRI Trunk ................................................................................................................17
2.6 SS7 Config........................................................................................................................18
2.6.1 SS7 Trunk ................................................................................................................18
2.6.2 SS7 MTP Link ..........................................................................................................20
2.6.3 SS7 Circuit...............................................................................................................21
2.6.4 SS7 Circuit Maintain..............................................................................................22
2.7 R2 Config..........................................................................................................................24
2.7.1 R2 Param................................................................................................................24
2.7.2 R2 Trunk ................................................................................................................26
2.8 PSTN Group Config..........................................................................................................27
2.8.1 E1/T1 Parameter.....................................................................................................27
2.8.2 Coder Group...........................................................................................................28
2.8.3 Dial Plan.................................................................................................................28
2.8.4 Dial Timeout ..........................................................................................................30
2.8.5 PSTN Profile..........................................................................................................30
2.8.6 PSTN Group...........................................................................................................31
2.8.7 PSTN Group Management.....................................................................................32

MTG600 User Manual
2.9 SIP Config.........................................................................................................................33
2.9.1 SIP Parameter.........................................................................................................33
2.9.2 SIP Trunk ...............................................................................................................33
2.9.3 SIP Account.............................................................................................................34
2.10 IP Group Config ...............................................................................................................35
2.10.1 IP Profile ..............................................................................................................35
2.10.2 IP Group...............................................................................................................37
2.10.3 IP Group Management .........................................................................................37
2.11 Call Routing....................................................................................................................38
2.11.1 Routing Parameter................................................................................................38
2.11.2 PSTN->IP Routing..................................................................................................38
2.11.3 PSTN->PSTN Routing ............................................................................................39
2.11.4 IP->PSTN Routing..................................................................................................40
2.11.5 IP->IP Routing.......................................................................................................41
2.12 Number Manipulation.....................................................................................................42
2.12.1 PSTN->IP Callee ....................................................................................................43
2.12.2 PSTN->IP Caller.....................................................................................................44
2.13 Voice & Fax.....................................................................................................................46
2.14 Management Parameter...................................................................................................48
2.14.2 SNMP Parameter..................................................................................................49
2.14.3 Data Backup.........................................................................................................50
2.14.4 Data Restore.........................................................................................................50
2.14.5 Version Information..............................................................................................51
2.14.6 Firmware Upload .................................................................................................51
2.14.7 Modify Password .................................................................................................51
2.14.8 Restart Device......................................................................................................52
3. FAQ..............................................................................................................................................53
3.1 How to get the IP address if user modified or forgot the default IP? ................................53
3.2 If meet other questions, please from Dinstar website and download trouble shootingV4.0
................................................................................................................................................53
4. Glossary...............................................................................................................................53

MTG600 User Manual
1/ 57
1. Product Introduction
1.1 Overview
MTG600 is a trunk gateway aimed at small and medium enterprise, and used to help
enterprise to realize the evolution from the traditional PBX to voice IP. On the one hand, it
supports PRI/SS7 protocol and adopts standard T1/E1 trunk interface to realize docking with
traditional PBX. On the other hand, adopt standard SIP protocol docking with various soft
switch to ensure PSTN seamless access to IP voice/NGN network, and achieving VoIP/FoIP
and more value-added service. MTG600 supports intelligent multiple trunk routing
technology, makes the operator easy to manage trunk routing by price optimum rule, and the
automatic switch-over between multiple trunk routing makes the network have high
reliability.
MTG600 has good call processing ability, and provides 2/4 T1/E1 interface. It is able to handle
a variety of signaling protocol and voice decoding. It supports the rich GUI configuration, the
user easily set and maintenance system. Mainly includes the following kinds of models:
-2E1
-4E1
A typical network diagram shows the function of MTG600 as below.
Figure 1-1-1 Application topology

MTG600 User Manual
2/ 57
1.2 Equipment Structure
1.2.1 Rear View
Figure 1-2-1 MTG600 Rear View
Table 1-2-1 MTG600 Rear View Description
PWR
The power interface, 200VAC, 50~60HZ
Port0-Port3
E1/T1 port, 2/4 E1 ports
FE0
The Service Ethernet Interface, standard 10/100BASE-TX Ethernet interfaces. Default IP
address is 192.168.1.111，default subnet mask is 255.255.255.0
FE1
Management Ethernet Interface. Default IP address is 192.168.11.1, default subnet mask is
255.255.255.0

MTG600 User Manual
3/ 57
1.2.2 Front View
Figure 1-2-2 MTG600 Front View
Table 1-2-2 MTG600 Front View Description
LED
Function
Color
Work Status
POWER
Power status indicator
Green
Off：Power is off
On: Power is on
RUN
Register indicator
Green
Slow blinking: Unregister
Fast blinking: Register
ALM
The failure of device
indicator
Yellow
Off: Normal
On: Failed
RST
Reset button, it is used to restart the device
CONSOLE
RS232 console port: it can be used to debug and configure the device. The baud rate is 115200
bps.
E1/T1
Indicating the connection
state of device E1/T1.
Green
Off：E1/T1 port connection normal
On: E1/T1 port connection and sending/ receiving
message normal
Flash:E1/T1 port connection failed
LINK
Indicating the connection
state of the network
Green
Off: Network connection failed
On: Network connection normal, and 0 indicates FE0
and 1 indicates FE1
SPEED
Indicating the network
bandwidth
Yellow
Off:10Mbps bandwidth
On:100Mbps bandwidth

MTG600 User Manual
4/ 57
1.2.3 RJ-48c Line sequence
MTG600 trunk gateway adopts standard RJ-48C interface and impedance value is 120Ω.
Connected end device by cross lines sequence.
1.3 Functions and Features
1.3.1 Protocol standard supported
●Standard SIP /PRI protocol
● NAT Traversing (STUN)
●Hypertext Transfer Protocol (HTTP)
● Domain Name System (DNS)
● ITU-T G.711A-Law/U-Law、G.723.1、G.729AB、iLBC (optional)
1.3.2 System Function
● Comfort Noise Generation (CNG)
● Voice Activity Detection (VAD)
● Adaptive (Dynamic) Jitter Buffer (DJB)
● DTMF mode: RFC 2833, SIP INFO and INBAND
● T.38/ Pass-Through FAX over IP
● HTTP/Telnet configuration
● Firmware upgrade by TFTP/Web
1.3.3 Industrial standards supported
● Stationary use environment: EN 300 019: Class 3.1

MTG600 User Manual
5/ 57
● Storage environment: EN 300 019: Class 1.2
● Transportation environment: EN 300 019: Class 2.3
● Acoustic noise: EN 300 753
● CE EMC directive 2004/108/EC
● EN55022: 2006+A1:2007
● EN61000-3-2: 2006,
● EN61000-3-3: 1995+A1: 2001+A2: 2005
● EN55024: 1998+A1: 2001+A2: 2003
● Certifications: FCC, CE
1.3.4 General hardware specification
●Power supply: 220VAC, 1.2A
● Temperature: 0~40℃(operational),-20~70℃(storage)
● Humidity: 10%~90%, no condensation
●Max power consumption: 10W
●Dimension (mm): 330*200*44
●Net Weight: 1.29 kg

MTG600 User Manual
6/ 57
2. Parameter Setting
2.1 Login
First, device FE0 port connect PC with string, and then fill FE0 IP address in browser, FE0 default
IP address is 192.168.1.111. It will request customer to input user name and password. Default
user name and password are “admin”.
If customer modified the default IP or forgot the IP, that can’t enter the configuration page.
Please connect PC and device serial with the serial line. Enter the CLI to view or modify the
equipment IP. Here IP is set to 172.16.99.120. In addition, hold down the RST button to restart
the device, customer can regain the port’s default IP. Then enter the IP address of device in the
browser address bar. Customer will see the following page.
Figure 2-1-1 Login Interfaces
The default user name and password is "admin". To guarantee the system safety, when login for
the first time. The system will prompt the user to modify the password. The interface is shown as
below.
Figure 2-1-2 Modify Password
Users through to traverse the left navigation tree, and can complete view, edit and configuration

MTG600 User Manual
7/ 57
device in the right configuration interface.
Figure 2-1-3 Description of System Information
2.2 Web interface structure and navigation tree
After entering configuration page, according to demand choose Chinese interface or English
interface, the default is English interface.
Figure 2-2-1 System Information
Users through to traverse the left navigation tree, and can complete view, edit and configuration
device in the right configuration interface.

MTG600 User Manual
8/ 57
Figure 2-2-2 Navigation tree
MTG configuration flow chart below:

MTG600 User Manual
9/ 57
2.3 Status & Statistics
Open the operation of the navigation tree information node, and can view the device information
and state system.
Figure 2-3-1 Status & Statistics
2.3.1 System Information
System information interface shows the general information and version information.
Figure 2-3-1 System Information

MTG600 User Manual
10 / 57
Table 2-3-1 System Information
MAC address
Hardware address of FE0 port
Service Ethernet Mode
Network mode of FE0, include: static and DHCP.
Service Ethernet Interface
Include: IP address, subnet mask, FE0 port default gateway
Management Ethernet Interface
Include IP address、subnet mask of FE1
DNS
DNS server IP address
System Up Time
Time elapsed from device power on to now
Traffic Statics
Total bytes of message received and sent by FE0 port
Equipment Type
Equipment type; this equipment is: MTG600
Hardware Version
Hardware version of device
DSP Version
Digital signal processing chip driver version
Web Version
Version of current WEB interface of device
Software Version
Software version of device running currently
Built Time
The build time of current software version

MTG600 User Manual
11 / 57
2.3.2 E1/T1 Status
Figure 2-3-2 E1/T1 Status
Table 2-3-2 Description of E1/T1 status
E1/T1 Port Status
1. LOS Alarm: Signal loss alarm, this alarm is created when receiving is lost; please check
the physical connection whether disconnected.
2. RAI Alarm: Receive remote alarm indication, it is a signal transmitted in the outgoing
direction when a terminal determines that it has lost the incoming signal. Receiving
remote alarm indication (RAI) means the far-end equipment over the T1 line has a
problem with the signal it is receiving from the upstream equipment.
3. AIS Alarm: The Alarm Indication Signal (AIS) failure is declared when an AIS defect is
detected at the input and the AIS defect still exists after the Loss of frame failure which is
caused by the unframed nature of the 'all-ones' signal is declared. The AIS failure is
cleared when the Loss Of Frame failure is cleared.
4. Disable: Means that this E1/T1 is not used.
5. ISDN/SS7 Signal Alarm: Means physical connection is normal, signaling link has
problem.
6. Active-OK: Means that physical connection and signaling link are normal.
E1/T1Channel Status
Frame-Sync: Non voice channel, which used as a synchronization channel
Idle: Means this channel is idle, when the channel is enabled and the cable is connected
OK.
3.Signal: Signal channel
4.Busy: Means this channel is occupied by voice
5. Fault: The channel is enabled but the cable is not connected.
6.Disable: Have not use this E1/T1 trunk
7.L-blocked:
Local blocked, means that communication can only be initiated from local
8.R-blocked:

MTG600 User Manual
12 / 57
Remote blocked, means that communication can only be initiated from remote
9.B-blocked:
Both Sides blocked, means that the two sides cannot communication
2.3.3 PSTN Trunk Status
Figure 2-3-3 PSTN Trunk Status
PSTN trunk status description：
1）PRI Link Status
PRI Trunk No.
The number of PRI trunk, each trunk corresponds to a PRI link
Trunk Name
Used to identify the name of the trunk
E1/T1Port No
Indicate the E1/T1 line occupied by the PRI trunk.
Link Status
Indicate whether the PRI link is established.
2）SS7 Link Status
SS7 Trunk No.
SS7 trunk number, each relay takes up a SS7 link.
Trunk Name
Used to identify the name of the trunk
E1/T1 Port No
Indicate the E1/T1 line occupied by the SS7 trunk.
Link Status
Indicate whether the SS7 link is established.
2.3.4 IP Trunk Status
Figure 2-3-4 SIPTrunk Status
IP trunk status
SIP Trunk No
The number of SIP trunk
Username
When SIP trunk is under registered mode, change the value in the configuration
shown in the account registration, If SIP trunk is under non-registered mode, the
value is meaningless, as '---'

MTG600 User Manual
13 / 57
Trunk Mode
Peer and Access two modes
Register Status
Indicate the status of SIP trunk（access mode）, register or unregister, when is under
peer to peer mode, the values is meaningless, as '---'
Link Status
Established and Fault status.
SIP Trunk No
The number of SIP trunk
2.3.5 PRI Call Statistics
图2-3-5 PRI Call Statistics description
PRI call statistics description
PRI Trunk No
The number of PRI trunk
Trunk Name
The name used to describe the PRI trunk
Current Calls
Number of lines that are being called currently
Accumulated Calls
Total number of calls from running start of system to current time.
ASR
The percent of calls completed in total calls.
This statistics page show the reasons for release of the call, including: Normal Call Clearing, Call
Rejected, User Busy, No User Response, No Circuit Available, Unassigned Number, Normal
Unspecified and others. Statistical information in an intuitive would be reflected on the pie char.

MTG600 User Manual
14 / 57
2.3.6 SS7 Trunk Call Statistics
Figure 2-3-6 SS7 Trunk Call Statistics
The parameters of SS7 trunk call statistics are the same with PRI parameters. Please refer to PRI
trunk call statistics.
2.3.7 SIP Call Statistics
Figure 2-3-7 SIP Trunk Call Statistics
SIP call statistics description
SIP Trunk No
The number of SIP trunk
Trunk Name
The name used to describe the PRI trunk
Current Calls
Number of lines that are being called currently

MTG600 User Manual
15 / 57
2.4 Network
Figure 2-4-1 Network Configuration
Network Configuration
Service Ethernet
Interface（FE0）
IP address
Set FE0 port static IP address.
Subnet Mask
Fill in subnet mask
Default Gateway
Fill in default gateway
Management
Ethernet Interface
（FE1）
IP address
Set FE1 port static IP address
Subnet Mask
Fill in subnet mask
DNS Server
Primary DNS
Fill in DNS Server IP address.
Secondary DNS
The secondary DNS server is option.
Ntoe：FE0 port IP and FE1 port IP should be set in different segments. After configure the
network address, and restart the gateway configuration to take effect.
2.5 PRI Config
PRI configuration includes PRI parameter and PRI trunk configuration
Figure 2-5-1 PRI Config

MTG600 User Manual
16 / 57
2.5.1 PRI Parameter
Figure 2-5-2 PRI Parameter
PRI parameter description
Calling Party
Numbering Plan
Provide six plans: Unknown, ISDN/Telephony numbering plan, data numbering plan,
telegraph numbering plan, national standard numbering plan, private numbering plan.
The default is ISDN/Telephony numbering plan.
Calling Party Number
Type
Six optional types are provided for calling party: Unknown, International number,
National number, Network special number, User number, Short code dialing. The
default option is Unknown.
Screening Indicator for
Displaying Caller
Number
Four options available: User provider, no shield; User provide, check and send; User
provide, check and having failure; Network provide. The default option is: User
provider, no shield.
Screening Indicator for
No Displaying Caller
Number
Four options available: User provider, no shield; User provide, check and send; User
provide, check and having failure; Network provide. The default option is: User
provider, no shield.
Called Party Numbering
Plan
Provide six plans: Unknown, ISDN/Telephony numbering plan, data numbering plan,
telegraph numbering plan, national standard numbering plan, private numbering plan.
The default is ISDN/Telephony numbering plan.
Called Party Number
Type
Six optional types are provided for called party: Unknown, International number,
National number, Network special number, User number, Short code dialing. The
default option is Unknown.
Information Transfer
Capability
Support speech and 3.1khz audio. The default option is speech.