Dinstar UC100-1T1S1O User manual

UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
I
Shenzhen Dinstar Co., Ltd.
Address: 9th Floor, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China
Postal Code: 518052
Telephone: [phone]
Fax: [phone]
Emails: [email protected], [email protected]
Website: www.dinstar.com
UC100-1T1S1O Universal Gateway
User Manual V1.0
User Manual V2.1

UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
II
Preface
Welcome
Thanks for choosing the UC100-1T1S1O Universal Gateway! We hope you will make full
use of this rich-feature gateway. Contact us if you need any technical support:
86-0755-26456110/112.
About This Manual
This manual provides information about the introduction of the gateway, and about how to
install, configure or use the gateway. Please read this document carefully before install the
gateway.
Intended Audience
This manual is aimed primarily at the following people:
Users
Engineers who install, configure and maintain the gateway.
Revision Record
Document Name
Document Version
Firmware Version
UC100-1T1S1O Universal Gateway
User Manual V1.0
V1.0 (2016/09/026)
1.53.2.35
Conventions
Gateway or device mentioned in this document refers to the UC100-1T1S1O gateway. Those
words in blue are the contents that users need to pay attention to.

Contents
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
III
Contents
1 Product Introduction......................................................................................................................1
1.1 Overview..........................................................................................................................................................1
1.2 Application Scenario ........................................................................................................................................1
1.3 Product Appearance..........................................................................................................................................2
1.4 Description of Indicators..................................................................................................................................2
1.5 Features & Functions .......................................................................................................................................3
1.5.1 Key Features ...........................................................................................................................................3
1.5.2 Physical Interfaces ..................................................................................................................................4
1.5.3 Voice Capabilities....................................................................................................................................4
1.5.4 FXS.........................................................................................................................................................4
1.5.5 FXO ........................................................................................................................................................5
1.5.6 Software Features....................................................................................................................................5
1.5.7 Supplementary Services..........................................................................................................................5
1.5.8 Environmental.........................................................................................................................................5
1.5.9 Maintenance............................................................................................................................................6
2 Quick Installation............................................................................................................................6
2.1 Installation Attentions ......................................................................................................................................6
2.2 Installation Steps ..............................................................................................................................................7
2.3 Network Connection ........................................................................................................................................7
2.3.1 Network Connection Diagram under Route Mode..................................................................................7
2.3.2 Network Connection Diagram under Bridge Mode ................................................................................8
2.4 Connect Gateway to Network ..........................................................................................................................9
2.4.1 Connect Gateway to Network via Network Port.....................................................................................9
2.4.2 Connect Gateway to Network via WiFi ..................................................................................................9
2.4.3 Preparations for Login ..........................................................................................................................10
2.4.4 Log In Web Interface ............................................................................................................................10
3 Basic Operation.............................................................................................................................11
3.1 Methods to Number Dialing........................................................................................................................... 11
3.2 Call Holding................................................................................................................................................... 11
3.3 Call Waiting.................................................................................................................................................... 11
3.4 Call Transfer................................................................................................................................................... 11
3.4.1 Blind Transfer .......................................................................................................................................11

Contents
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
IV
3.4.2 Attended Transfer..................................................................................................................................12
3.5 Function of Flash-hook ..................................................................................................................................13
3.6 Description of Feature Code ..........................................................................................................................13
3.7 Send or Receive Fax.......................................................................................................................................14
3.7.1 Fax Mode Supported.............................................................................................................................14
3.7.2 Explanation of T.38 and Pass-through ..................................................................................................14
3.8 Function of RST Button.................................................................................................................................15
3.9 Query IP Address and Restore Default Setting...............................................................................................16
4 Configuration Wizard...................................................................................................................17
4.1 Configuration Wizard.....................................................................................................................................17
4.1.1 UC100 Regarded as Terminal and Registered to SIP Server.................................................................17
4.1.2 Other SIP Clients registered to UC100 .................................................................................................18
4.1.3 UC100 Connected to PBX through Trunking .......................................................................................19
4.1.4 UC100 Serving as VPN Client..............................................................................................................19
5 Configurations on Web Interface ................................................................................................20
5.1 Introduction to Web Interface.........................................................................................................................20
5.2 Status..............................................................................................................................................................21
5.2.1 Overview...............................................................................................................................................21
5.2.2 SIP.........................................................................................................................................................22
5.2.3 PSTN.....................................................................................................................................................23
5.2.4 DHCP Client List..................................................................................................................................24
5.2.5 Current Call...........................................................................................................................................24
5.2.6 CDRs.....................................................................................................................................................24
5.2.7 Service ..................................................................................................................................................25
5.3 System............................................................................................................................................................25
5.3.1 Setting...................................................................................................................................................26
5.3.2 User Manager........................................................................................................................................27
5.3.3 Provision...............................................................................................................................................27
5.3.4 Operation Log.......................................................................................................................................29
5.3.5 Service Log...........................................................................................................................................29
5.3.6 Config Changes Log .............................................................................................................................29
5.3.7 Backup/Restore/Upgrade ......................................................................................................................30
5.3.8 GSM Tools............................................................................................................................................31
5.3.9 Voice .....................................................................................................................................................32
5.3.10 Command Line....................................................................................................................................32
5.3.11 Diagnostics..........................................................................................................................................32
5.3.12 Cloud Server .......................................................................................................................................33

Contents
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
V
5.3.13 Reboot.................................................................................................................................................33
5.4 Network ..........................................................................................................................34
5.4.1 Setting...................................................................................................................................................34
5.4.2 Access Control ......................................................................................................................................37
5.4.3 Firewall.................................................................................................................................................38
5.4.4 DHCP Server.........................................................................................................................................40
5.4.5 Port Mapping ........................................................................................................................................41
5.4.6 DMZ Setting .........................................................................................................................................42
5.4.7 Diagnostics............................................................................................................................................42
5.4.8 DDNS....................................................................................................................................................44
5.4.9 Static Route...........................................................................................................................................46
5.4.10 UPnP Client.........................................................................................................................................47
5.4.11 VPN Client..........................................................................................................................................47
5.4.12 Hosts ...................................................................................................................................................50
5.5 Profile.............................................................................................................................................................50
5.5.1 SIP.........................................................................................................................................................51
5.5.2 FXS/FXO..............................................................................................................................................53
5.5.3 Codec....................................................................................................................................................59
5.5.4 Number .................................................................................................................................................60
5.5.5 Time ......................................................................................................................................................62
5.5.6 Manipulation.........................................................................................................................................63
5.5.7 Dialplan.................................................................................................................................................64
5.6 Extension........................................................................................................................................................66
5.6.1 SIP.........................................................................................................................................................66
5.6.2 FXS.......................................................................................................................................................67
5.6.3 Ring Group............................................................................................................................................71
5.7 Trunk..............................................................................................................................................................72
5.7.1 SIP.........................................................................................................................................................72
5.7.2 FXO ......................................................................................................................................................74
5.7.3 GSM......................................................................................................................................................77
5.8 Call Control....................................................................................................................................................81
5.8.1 Setting...................................................................................................................................................82
5.8.2 Route Group..........................................................................................................................................83
5.8.3 Route.....................................................................................................................................................84
5.8.4 Feature Code.........................................................................................................................................86
5.8.5 IVR........................................................................................................................................................87
5.8.6 SMS Route............................................................................................................................................89
5.8.7 SMS ......................................................................................................................................................90

Contents
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
VI
5.8.8 USSD....................................................................................................................................................91
5.8.9 Diagnostics............................................................................................................................................92
6 Glossary..........................................................................................................................................93

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
1
1 Product Introduction
1.1 Overview
The UC100-1T1S1O gateway is a multi-functional and all-in-one gateway, which integrates
voice service (PSTN and VoIP) and data service (LTE 4G/WCDMA 3G). It provides three
interfaces (including LTE, FXS and FXO), offering seamless connectivity to VoIP Network,
PLMN and PSTN.
Based on SIP, UC100-1T1S1O not only can interact with IPPBX, softswitchd and SIP-based
network platforms, but also supports types of GSM/WCDMA/LTE frequency ranges, thus
meeting the worldwide requirements about the mobile network.
Besides, the gateway has built-in WiFi and high-speed data handling capacity, allowing users
to enjoy high-speed internet surfing through WiFi or LAN ports.
UC100-1T1S1O is ideally suitable for personal use. Meanwhile, it is perfect for small and
micro enterprises, offering high-speed internet access, good voice service and message
service.
1.2 Application Scenario
The application scenario of UC100-1T1S1O universal gateway is shown as follows:

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
2
Figure 1-1 Application Scenario of UC100-1T1S1O
IP
IP
FXO
LAN
SIP
Internet
WAN
Laptop
SIP Server
PC
Extension
Analog Telephone
WiFi
LTE
SMS/USSD (Data)
PSTN
UC100-1T1S1O
FXS
WAN
Trunk
IP
1.3 Product Appearance
Front View:
Back View:
1.4 Description of Indicators
Indicator
Definition
Status
Description

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
3
PWR
Power Indicator
Off
There is no power supply or power
supply is abnormal.
On
The UC100 device is powered on.
RUN
Running Indicator
Slow
Flashing
The device is initialized successfully
and is running normally
On
The device is being initialized.
Off
The device is not running normally.
WiFi
WiFi Indicator
Fast
Flashing
WiFi is in normal running.
Off
WiFi is not turned on.
On
The WiFi module is faulty.
FXS
FXS In-use Indicator
Slow
Flashing
The FXS port is in idle status.
On
The FXS port is in off-hook status.
Off
The FXS port is faulty
FXO
FXO In-use Indicator
Slow
Flashing
The FXO port is initialized
successfully and is in idle status.
On
The FXO port is currently occupied
by a call.
Off
The FXO port is faulty.
WAN/LAN
Network Connection
Indicator
Off
Network does not work or network
cable is not connected.
Fast
Flashing
Network is successfully connected.
SIM
LTE 4G Indicator
Slow
Flashing
The LTE module or the SIM card
cannot be detected.
(Flash every four seconds)
Fast
Flashing
It is detected that the SIM card has
been inserted and registered
successfully.
(Flash every two seconds)
1.5 Features & Functions
1.5.1 Key Features
FXS/FXO/LTE interface on a single gateway
Send/receive calls from PSTN/PLMN via FXO
Flexible dial plan and routing strategies based on time, number and source IP etc.
IVR Customization
Support high-speed NAT forwarding and WIFI hotspot

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
4
Serve as VPN client
Built-in SIP server, support up to 32 SIP extensions and 8 cocurrent calls
User-friendly web interface, multiple management ways
1.5.2 Physical Interfaces
FXS Port: 1
FXO Port: 1
SIM Slot: 1
Network Port：1 WAN Port & 3 LAN Ports（10/100 Base-T RJ45）
WiFi：2.4Ghz 802.11n
1.5.3 Voice Capabilities
VoIP Protocols: SIP over UDP/TCP/TLS, SDP, RTP/SRTP
Codecs: G.711a/μ law, G.723.1, G.729A/B
Silence Suppression
Comfort Noise Generator(CNG)
VoiceActivity Detection(VAD)
Echo Cancellation: G.168 with up to 128ms
Dynamic Jitter Buffer
Adjustable Gain Control
Automatic Gain Control （AGC）
Call Progress Tones: Dial Tone, Ring Back Tone, Busy Tone
FAX: T.38 and Pass-through
NAT Traversal: STUN/UPnP
DTMF: RFC2833/Signal/Inband
1.5.4 FXS
FXS Connector: RJ11
Caller ID: Bellcore Type 1&2, ETSI, BT, NTT and DTMF
Answer and Disconnect Signaling:Answer, Disconnect, Busy Tone
Polarity Reversal
Hook Flash

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
5
1.5.5 FXO
FXO Connector: RJ11
Caller ID: FSK and DTMF
Polarity Reversal
Answer Delay
Busy Tone Detection
No Current Detection
1.5.6 Software Features
Ring Group
Routing Groups
Caller/Called Number Manipulation
Routing Based on Time Period
Routing Based on Caller/Called Number Prefix
Routing Based on Source Trunks
Dial Rules
Failover Routing
FXO Impedance Auto Match
IVR Customization
AutoAttendant Function
CDRs
1.5.7 Supplementary Services
Call Forwarding （Unconditional/Busy/No Reply）
Call Waiting and Call Holding
Call Transfer (Blind & Attended)
Intra-group Pick-up
Hotline
No Disturbing
Three Parites Conversation
1.5.8 Environmental
Power Supply: 12VDC, 1A
Power Consumption: 10W

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
6
Operating Temperature: 0 ℃~ 45 ℃
Storage Temperature: -20 ℃~80 ℃
Humidity: 10%-90% (Non-Condensing)
Dimensions：143×86×25mm（W/D/H）
Weight：0.4kg
1.5.9 Maintenance
Web GUI for Configuration
Telnet Management
Configuratuin Restore & Backup
Multiple Languages
Firmware Upgrade: support HTTP/HTTPS/TFTP/FTP
Auto Provision
CDR Query and Export
Syslog Query and Export
Network Tools: Ping,Traceroute and Nslookup
Network Capture
2 Quick Installation
2.1 Installation Attentions
To avoid unexpected accident or device damage, please reed the following instructions before
installing the UC100-1T1S1O gateway.
The adapter of the gateway accepts DC input voltage of 12V. Please ensure stable and
safe power supply;
To reduce the interference to telephone calls, please separate power cables from
telephone lines.
To guarantee stable running of the gateway, please make sure that there is enough network
bandwidth.
For better heat dissipation, please place the gateway on a flat surface and do not pile up
If WiFi is turned on, please ensure the WiFi antennas are well connected with the gateway
If you want the gateway to communicate with the LTE network, please insert an SIM card.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
7
2.2 Installation Steps
Connect WiFi antennas to the left and right side of the gateway, and then connect the GSM
antenna to the back panel of the gateway.
LTE Antennas
WiFi Antennas
Connect the power adapter to the power jack;
Connect telephone line to the FXS port and connect PSTN line to the FXO port;
Connect network cable to the LAN port(s) and WAN port (please refer to 2.3 Network
Connection);
Insert a SIM card to the SIM slot.
2.3 Network Connection
UC100-1T1S1O works in two network modes: route mode and bridge mode. When it is under
the route mode, the IP address of WAN port must be different from the IP address of LAN
port. But when it is under the bridge mode, the IP address of WAN port and that of LAN port
are the same.
2.3.1 Network Connection Diagram under Route Mode
Under the route mode, the default IP address of WAN port is a DHCP IP address, while the
default IP address of the LAN port is a static IP address, namely 192.168.11.1.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
8
Figure 2-1 Network Connection Diagram under Route Mode
Router
192.168.1.XXX
192.168.11.1
192.168.11.XXX
UC100-1G1S1O
DHCP Server
DC12V
WAN
LAN0
LAN1
LAN2
FXS
WPS
RST
IP Netowk
FXO
Note: The IP address of LAN port of the gateway and the IP address of PC must be at the
same network segment, while that of WAN port is at a different network segment.
2.3.2 Network Connection Diagram under Bridge Mode
Under the Bridge mode, the IP address of WAN port is the same with that of LAN port.
Generally, when the gateway works under the bridge mode, the IP address of the gateway has
been modified. In the following diagram, it is assumed that the IP address has been modified
into 172.16.80.1.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
9
Figure 2-2 Network Connection Diagram under Bridge Mode
172.16.80.XXX
Switch/Router
172.16.80.1
UC100-1G1S1O
DC12V
WAN
LAN0
LAN1
LAN2
WPS
RST
FXS
FXO
Note: The IP address of PC and that of WAN port of the UC100-1T1S1O gateway are at the
same network segment.
2.4 Connect Gateway to Network
The above network diagrams show how to connect the gateway to network through network
ports. In fact, the gateway can also be connected to network through WiFi.
2.4.1 Connect Gateway to Network via Network Port
Please connect the UC100-1T1S1O gateway to network according to the network diagrams in
Section 2.3 Network Connection. Then connect a telephone to the FXS port. Dial *158# to
query the IP address of LAN port. Modify the IP address of PC to make it at the same network
segment of LAN port of the gateway.
2.4.2 Connect Gateway to Network via WiFi
Connect power source to the gateway, and then use a laptop to search the SSID of the gateway.
The default SSID is domain_the last six characters of the Mac address, for example, if the
mac address is F8-A0-3D-59-09-A3, the default SSID is domain_5909a3.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
10
By default, there is no password for WiFi, and the built-in DHCP server is turned on.
2.4.3 Preparations for Login
Modify the IP address of the PC to make it at the same network segment with the
UC100-1T1S1O gateway, since the default IP address of LAN port of the gateway is
192.168.11.1.
Check the connectivity between the PC and the UC100-1T1S1O. Click Start Run of PC
and enter cmd to execute ‘ping 192.168.11.1’to check whether the IP address of LAN port
runs normally.
2.4.4 Log In Web Interface
Open a web browser and enter the IP address of LAN port (the default IP is 192.168.11.1).
Then the login GUI will be displayed.
You also can enter the IP address of WAN port, but it’s required to modify the IP address of
PC to make it at the same network segment with that of WAN port.
It is suggested that you should modify the username and password for security consideration.
Figure 2-3 Login GUI of UC100-1T1S1O
Both the default username and password are admin. Click Login to enter into the web
interface.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
11
3 Basic Operation
3.1 Methods to Number Dialing
There are two methods to dial telephone number or extension number:
Dial the called number and wait for 4 seconds for dialing timeout, or dial the called
number directly (the system will judge whether the dialing is completed according to
Digitmap and Regular Expression dialplans).
Dial the called number and press #.
3.2 Call Holding
If a calling party places a call to a called party which is otherwise engaged, and the called
party has the call holding feature enabled, the called party is able to switch to the new
incoming call while keeping the current call holding on by pressing the flash button or the
flash hook.
When the called party presses the flash button or the flash hook once again, he or she will
switch back to the first call.
3.3 Call Waiting
If a calling party places a call to a called party which is otherwise engaged, and the called
party has the call waiting feature enabled, the calling party will hear a IVR voice ‘Please hold
on, the subscriber you dialed is busy’ and the called party will hear three beeps.
By pressing the flash button or the flash hook, the called party is able to switch between the
new incoming call and the current call.
3.4 Call Transfer
3.4.1 Blind Transfer
Blind transfer is a call transfer in which the transferring party connects the call to a third party
without notifying the third party.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
12
Example: A gives a call to B and B wants to blindly transfer the call to C. Operation
instructions are as follows:
1. A dials the extension number of B;
2. The extension of B rings, and B picks up the phone. Then A and B go into conversation;
3. B presses *1 to trigger blind transfer (at the same time,A can hear the waiting tone). Then
B dials the extension number of C ( end up with # or wait for 4 seconds);
4. The extension of C rings, B hangs up the phone and C picks up the phone. Then C and A
goes into conversation.
Note:
On the ‘Call Control Feature Code’page, feature code service should be ‘On’.
If B hears continuous busy tones after he dials the extension number of C, it means the call
has timed out.
3.4.2 Attended Transfer
Attended transfer is a call transfer in which the transferring party connects the call to a third
party after he confirms that the third party agrees to answer the call.
Example: A gives a call to B and B wants to attended transfer the call to C. Operation
instructions are as follows:
1. A dials the extension number of B;
2. The extension of B rings, and B picks up the phone. Then A and B go into conversation;
3. B presses *2 to trigger attended transfer (at the same time, A can hear a waiting tone). Then
B dials the extension number of C;
4. Then one of the following situations will happen:
a. If the extension of C cannot be reached because the dialing/call has timed out, C rejects
the call or C is busy, B will automatically switch to the conversation with A.
b. The extension of C rings (at the same time, B can hear a ringback tone). If B hangs up
the phone at this moment, A will continue to hear the waiting tone. Then if A also hangs up
the phone, the extension of C will continue to ring. If C picks up the phone at this moment,
the call will end directly.
c. The extension of C rings and then C picks up the phone. C and B go into conversation,
and A will continue to hear a waiting tone. If it’s B that hangs up the phone at this moment, C
and A go into conversation. If it’s C that hangs up the phone, B and A go into conversation.

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
13
3.5 Function of Flash-hook
AssumeA and B are in a call conversation:
If A presses the flash hook, and then dial the number of C, A and C go into conversation and
meanwhile the call between A and B is kept holding.
Then, if Apresses the flash hook and dial 1, the conversation will switch back to A and B; if A
presses the flash hook and dial 2 , the conversation will switch to A and C; if A presses the
flash hook and dial 3, the conversation will switch to A , B and C (three parties conversation).
3.6 Description of Feature Code
UC100-1T1S1O provides convenient telephone functions. Connect a telephone to the FXS
port and dial a specific feature code, and you can query conrresponding information.
Code
Corresponding Function
*159
Dial *159 to inquiry WAN IP
*158
Dial *158 to inquiry LAN IP
*114
Dial *114 to inquiry phone number
*157*
Dial *157*0 to set route mode; dial *157*1 to set bride mode
*150*
Dial *150*1 to set IP address as static IP address; dial *150*2 to set IP
address as DHCP IP address
*152*
Dial *152* to set IPv4 address, for example:
Dial *152*192*168*1*10# to set IPv4 address as 192.168.1.10
*156*
Dial *156* to set IPv4 gateway, for example:
Dial *156*192*168*1*1# to set IPv4 gateway as 192.168.1.1
*153*
Dial *153* to set IPv4 netmask, for example:
Dial *153*255*255*0*0*# to set IPv4 netmask as 255.255.0.0
*111
Dial *111 to restart the UC100 devic
*51
Dial *51 to enable the call waiting service
*50
Dial *50 to disable the call waiting service
*1
Dial *1 to trigger blind transfer, for example:
Dial *18000, and you can blind transfer to the extension number 8000
*2
Dial *2 to trigger attended transfer, for example:
Dial *28000#, and you can attended transfer to the extension number
8000

Error! Use the Home tab to apply 标题 1 to the text that you want to appear
here.Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
UC100-1T1S1O User Manual
Copyright©2011-2016 Dinstar
14
*72*
Enable unconditional call forwarding service. Example: Dial *72*8000,
and calls will be unconditionally forwarded to extension number 8000
*73
Disable unconditional call forwarding service
*90*
Enable the ‘call forwarding on busy’service. Example: Dial *90*8000,
and calls will be forwarded to extension number 8000 when the called
number is busy
*91
Disable the ‘call forwarding on busy’service
*92*
Enable the ‘call forwarding on no reply’service. Example: Dial
*92*8000, and calls will be forwarded to extension number 8000 when
there is no reply from the called number
*93
Disable the ‘call forwarding on no reply’service
*78
Enable the ‘No Disturbing’service
*79
Disable the ‘No Disturbing’service
**
Pick up the ringing extension which is in the same ringgroup. Example:
Dial**8000, and you can take the incoming call of extension number
8000
*160*
Dail *160*1# to allow HTTP WAN access, Dial *160*0# to deny
HTTP WAN access
Note:
A voice prompt indicating successful configuration will be given after each configuration
procedure. Please do not hang up until hearing this voice prompt.
3.7 Send or Receive Fax
3.7.1 Fax Mode Supported
T.38（IP-based）
T.30（Pass-Through）
3.7.2 Explanation of T.38 and Pass-through
T.38 is an ITU recommendation for allowing transmission of fax over IP networks in real time.
Under the T.38 mode, analog fax signal is converted into digital signal and fax signal tone is