Directed Directechs DB3 User manual

DB3 403.HKHT1
v3.25
2013 Hyundai Accent

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Installation 6
Wiring diagram without OEM alarm 6
Wiring diagram with OEM alarm 7
Locating components in the vehicle 8
Vehicle connections 9
Module programming 12
With Transponder Immobilizer 12
Without Transponder Immobilizer 13
Connecting the module 14
LED diagnostics and troubleshooting 15
Soft reset 17
Hard reset 17
Feature programming 18
Feature and option list 19
Limited one year consumer warranty 20
Quick reference guide 21
Contents

3403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
DB3 is an all-in-one door lock and override module.
Warning!
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs
Mobile application for smartphones. Refer to “Connecting the module” for more information.

4403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Immobilizer Bypass-Data No Key Req'd
Remote Start Takeover
Tach / RPM Output
Brake Status (foot brake)

5403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible T-Harness is not compatible. Keys required for
programming 1Keys required for operation 0
Vehicle Takeover Refer to the Quick Reference Guide section for more details.
Firmware notes
Important! If your vehicle is not equipped with transponder immobilizer and also does not use CAN connections, please flash your
module with analog firmware
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
Refer to the "Vehicle connections" following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if
not supported in data.
[2] Tach: An optional connection required on some remote starters, which do not support a tach signal in D2D.
[3] EMS COM: This connection is not required in US vehicles without transponder immobilizer.
[4] RAP Off: Required only if RAP Off does not operate over data.

6403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
D2D Port
OBDII
Diagnostic Connector
(connector side view)
(+) Ignition Output
(+) Accessory Output
(AC) Tach Input
(+) Starter Output
(+) 12V Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan : 4
(AC) Tach Output: Violet/White: 5
1412
10 42
1 8
169
9: Pink:
(+) Ignition
Input
Wiring diagram without OEM alarm
XKD2D65
(-) Parking Lights Output
(-) Unlock Output
(-) Lock Output
Refer to the “Vehicle connections”
section for the corresponding
connector, pin and wire color
of your vehicle.
Cut
EM01
(black 21-pin connector left of junction box)
11
EMS COM:
Blue/Orange, pin 11
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (connector side): Orange/Yellow: 9
Immo. Data Interrupt (vehicle side): Yellow/Black: 10
Immo. Data Interrupt (connector side): Orange/Black: 11
(-) RAP Off Output: Green/Black: 2
Ignition Switch
(black 6-pin connector)
1 2 3
45 6
(-) Ground
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
(+)12V: Green, pin 1
(+) Starter: White, pin 3
(+) Ignition: Pink, pin 4
(+) Accessory: Orange, pin 2
(-) Hood Pin Input Hood Pin

7403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
D2D Port
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
OBDII
Diagnostic Connector
(connector side view)
HS CAN High: Tan/Black: 3
HS CAN Low: Tan : 4
1412
10 42
1 8
169
9: Pink:
(+) Ignition
Input
Wiring diagram with OEM alarm
XKD2D65
Refer to the “Vehicle connections”
section for the corresponding
connector, pin and wire color
of your vehicle.
(-) Parking Lights Output
(-) Unlock Output
(-) Lock Output
(-) Disarm Output
4 x 1A
Diodes
(-) Factory Alarm Diszrm (-) Factory Alarm Arm (-) Lock (-) Unlock
86 85
30
87a
87
(-) Lock Detection
(+) 12V
Cut
Cut
EM01
(black 21-pin connector left of junction box)
11
EMS COM:
Blue/Orange, pin 11
Immo. Data Interrupt
(connector side): Yellow: 8
Immo. Data Interrupt
(vehicle side): Orange/Yellow: 9
Immo. Data Interrupt
(connector side): Yellow/Black: 10
(AC) Tach Output: Violet/White: 5
Immo. Data Interrupt
(vehicle side): Orange/Black: 11
(-) RAP Off Output: Green/Black: 2
(+) Ignition Output
(+) Accessory Output
(AC) Tach Input
(+) Starter Output
(+) 12V Input (+)12V: Green, pin 1
(+) Starter: White, pin 3
(+) Ignition: Pink, pin 4
(+) Accessory: Orange, pin 2
Ignition Switch
(black 6-pin connector)
1 2 3
45 6
(-) Ground
(-) Hood Pin Input Hood Pin

8403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle

9403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2013 Hyundai Accent. Refer to “Pre-installation and application warnings” for a list of important notes.
Data 14-pin blue connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H1/1 Light Green No Connection No Connection
H1/2 Violet/Yellow No Connection No Connection
H1/3 Tan/Black (DATA) HS CAN High OBD-Data Link Connector, black 16 pin plug, pin 6 Data Green (C-CAN)
H1/4 Tan (DATA) HS CAN Low OBD-Data Link Connector, black 16 pin plug, pin 14 Data Orange (C-CAN)
H1/5 Orange/Green (DATA) HS CAN High No Connection
H1/6 Orange/Brown (DATA) HS CAN Low No Connection
H1/7 Brown Relay N.O. - No Connection No Connection
H1/8 Yellow Relay COM - Immo. Data Interrupt (vehicle side) [3] Left of Dash Fuse Box, black 21 pin plug (EM11), pin 11 Data Blue/Orange (EMS COM)
H1/9 Orange/Yellow Relay N.C. - Immo. Data Interrupt (conn. side) [3] Left of Dash Fuse Box, black 21 pin plug (EM11), pin 11 Data Blue/Orange (EMS COM)
H1/10 Orange/Red Relay N.C. - No Connection No Connection
H1/11 Yellow/Red Relay COM - No Connection No Connection
H1/12 Brown/Red Relay N.O. - No Connection No Connection
H1/13 Red (+) W2W Only - 12 Volt Ignition Switch, black 6 pin plug, pin 1 + Green (50A)
H1/14 Black (-) W2W Only - Ground (chassis ground)
Output 12-pin red connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H2/1 Black/White (-) W2W Only - E-Brake Output Remote Starter
H2/2 Green/Black (-) RAP Off Output [4] Driver Kick, white 39 pin plug (MF11), pin 2 - Brown/Orange
H2/3 Green/White (-) W2W Only - Door Output Remote Starter
H2/4 Red/Black (-) W2W Only - Trunk Output Remote Starter
H2/5 Violet/White (AC) W2W Only - Tach Output [2] Remote Starter
H2/6 Gray (+) W2W Only - Brake Output Remote Starter
H2/7 Gray/Black No Connection No Connection
H2/8 Violet/Green No Connection No Connection
H2/9 Violet/Brown No Connection No Connection
H2/10 Yellow/Black Immo. Data Interrupt (vehicle side) [2] Left of Dash Fuse Box, black 21 pin plug (EM11), pin 11 Data Blue/Orange (EMS COM)
H2/11 Orange/Black Immo. Data Interrupt (conn. side) [2] Left of Dash Fuse Box, black 21 pin plug (EM11), pin 11 Data Blue/Orange (EMS COM)
H2/12 Blue/Red (-) W2W Only - Hood Output Remote Starter
Input 10-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color

10 403.HKHT1 3.25 2013 Hyundai Accent
©2022 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/1 Green (-) W2W Only - Lock Input Remote Starter
H3/2 Blue (-) W2W Only - Unlock Input Remote Starter
H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter
H3/4 Red/Black No Connection No Connection
H3/5 Violet/Black No Connection No Connection
H3/6 White/Black No Connection No Connection
H3/7 Pink/White No Connection No Connection
H3/8 Violet No Connection No Connection
H3/9 Pink (+) Ignition Input Remote Starter
H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input Remote Starter
D2D 4-pin white connector (H4)
Module
Conn./Pin Color Description
H4/1 Blue (Data) TX
H4/2 Black (-) Ground
H4/3 Green (Data) RX
H4/4 Red (+) 12 Volt
RF 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A No Connection
H5/2 N/A No Connection