Directed Directechs DS3 User manual

DS3+ / DS4+ 933.HKHT1
v3.25.195.3
2013 Hyundai Sonata
THHYN3-DS4+,DS3+-ONLY Compatible
(Sold Separately)

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Installation 6
Wiring diagram with T-Harness (THHYN3) 6
Wiring diagram 7
Locating components in the vehicle 8
Vehicle connections 9
Module programming 12
With Transponder Immobilizer 12
Without Transponder Immobilizer 13
Module programming for security-only installations 14
Pairing remotes 15
Connecting the module 15
8556T Temperature Sensor 15
8504D Combo Sensor 15
RF Systems 15
When used in conjunction with SmartStart 16
D2D port configuration 16
Manual transmission 17
LED diagnostics and troubleshooting 18
Soft reset 20
Hard reset 20
Tach learning procedure (not needed with Virtual Tach) 21
Initializing Virtual Tach (not needed with hardwired or data tach applications) 21
Limited lifetime consumer warranty 22
Quick reference guide 23
Contents

3933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a
digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on
the DIRECTLINK text in the header for additional information.
DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,
and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.
The following methods are available to configure modules:
• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)
• Desktop Application: Directlink DT (DS3/DS3+ and DS4/DS4+)
• Mobile Device: Directlink App (DS4/DS4+ only)
When Flashing via Directlink DT (Desktop app) or via the Web, an XKloader2 will be required.
To configure via Web or DirectLink DT (mobile app):
1. Disconnect the main module from any (+) 12V power source.
2. Connect the module to your computer using the XKLoader2.
3. Follow the steps in the pop-up window that will be displayed when the module is detected.
Notes:
•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.
•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.)
•When using Windows 11 or newer, Directlink DT is mandatory.
The DS4/DS4+ module is designed to be configured using the DirectLink application through mobile devices.
To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be
configured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to
configure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not
compatible with the DirectLink app for mobile devices.
To configure via DirectLink DT (mobile app):
1. Follow and complete the wiring diagram(s) related to your installation through the app.
2. When installation is complete, select Configure DS4/DS4+.
3. Follow the on-screen instructions.
FLASH REQUIRED!
FLASH REQUIRED!
4 White

4933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
DS4+/DS3+/VSM3 Only
Control of aftermarket alarm with OEM remote
Fuel level/EV battery level
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
Accessory Activation
Ignition Activation
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
Door Locks Status
E-Brake Status
Ignition Status

5933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible THHYN3 Keys required for
programming 1Keys required for operation 0
Vehicle Takeover Refer to the Quick Reference Guide section for more details.
Firmware notes
Important! If your vehicle is not equipped with transponder immobilizer and also does not use CAN connections, please flash your
module with analog firmware
A DS4+ module is required for this installation, as the Relay harness (H2), 10-pin white connector is used.
The optional Plug & Play THHYN3 T-Harness is sold separately
All T-Harness wires not listed in the diagram are not required for the installation. Loose wires such as Siren Output and Hood Input
may need to be pulled from the tapped section of the T-harness. Refer to the "wiring diagram with T-Harness" for more information on
connections and installation instructions.
The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
Fuses positioning: It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed
on each wiring diagram.
Refer to the "Vehicle connections" following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if
not supported in data.
[2] Siren: The siren is only required when enabling the security features during module flashing.
[3] Starter Disable/Antigrind: The Green wire is only required for starter disable and antigrind applications.
[4] EMS COM: This connection is not required in US vehicles without transponder immobilizer.

6933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Cut the
Yellow/Black loop
for this installation.
Immo. Data Interrupt (vehicle side): Blue/White
Immo. Data Interrupt (connector side): Blue
Immo. Data Interrupt (vehicle side): Orange/Black
Immo. Data Interrupt (connector side): Yellow/Black
B-CAN Wires
Refer to the “Vehicle connections” section. HS CAN 2 High: Orange/Green
HS CAN 2 Low: Orange/Brown
Wiring diagram with T-Harness (THHYN3)
Hood Pin
Siren
(-) Hood Input: Gray
(+) Siren Output: Brown/Red
Connector
1 - EM11 White 55-pin connector
2 - EM11 White 58-pin connector
12
41
OR
OR
10
3 - EM11 White 43-pin connector
10
Cut
THHYN3 (Optional T-Harness)
OBDII Diagnostic
(connector side view)
DS4+
Ignition Switch
Parking Lights
Refer to the “Vehicle connections” section.
(-) Parking Lights Output: Lt. Green/Black
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20
EMS COM connections are only
needed if the vehicle has a
transponder/immobilizer.
Refer to the Vehicle connections section
for the connector, pin and wire color.
8-Pin White Connector
22-Pin White Connector
10-Pin White Connector
12-Pin Black Connector

7933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
16
8
9
1
Wiring diagram
Immo. Data Interrupt (vehicle side): Blue/White: 1
Immo. Data Interrupt (connector side): Blue: 3
(-) Ground: Black: 10
HS CAN Low: Tan: 1
HS CAN High: Tan/Black: 2
HS CAN 2 High: Orange/Green: 4
HS CAN 2 Low: Orange/Brown: 3
Immo. Data Interrupt (vehicle side): Orange/Black: 7
(+) 12V Input: Red: 6 & 12
Immo. Data Interrupt (connector side): Yellow/Black: 8
C-CAN High: pin 6
C-CAN Low: pin 14
Hood Pin
Siren
(-) Parking Lights Output: Lt. Green/Black: 1
OBDII Diagnostic
(connector side view)
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
Cut
(+) Ignition Input/Output: Pink: 10
(+) 12V Input: Red: 5
(+) Accessory Output: Orange: 8
(+) 12V Input: Red/Black: 2
(+) Starter Output (vehicle side): Violet: 7
Starter Input (connector side): Green: 6
(+)12V:
Green,
pin 1 (+) Starter:
Yellow, pin 3
(+) Ignition: Pink, pin 4
(+) Accessory:
Orange,
pin 2
Ignition Switch
(white connector)
1 2 3
45 6
CUT
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20
B-CAN Wires
Refer to the “Vehicle connections” section.
Parking Lights
Refer to the “Vehicle connections” section.
Connector
1 - EM11 White 55-pin connector
2 - EM11 White 58-pin connector
12
41
OR
OR
10
3 - EM11 White 43-pin connector
10
EMS COM connections are only
needed if the vehicle has a
transponder/immobilizer.
Refer to the Vehicle connections section
for the connector, pin and wire color.

8933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle

9933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2013 Hyundai Sonata. Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low 1 data link connector, black 16 pin plug, pin 14 data yellow (C-CAN) Mandatory
H1/2 Tan/Black (Data) HS CAN High 1 data link connector, black 16 pin plug, pin 6 data white (C-CAN) Mandatory
H1/3 Orange/Brown (Data) HS CAN Low 2 dash fuse box, rear, white 24 pin plug (F), pin 11 data yellow/orange (B-CAN) Mandatory
H1/4 Orange/Green (Data) HS CAN High 2 dash fuse box, rear, white 24 pin plug (F), pin 12 data white/orange (B-CAN) Mandatory
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown No Connection No Connection
H1/7 Orange/Black (Data) Immo. Data Interrupt (vehicle side) [4] driver kick, white 43 pin plug, pin 10
This connection is not required in US vehicles without transponder
immobilizer.
data blue (EMS COM) Remote Start
Only
H1/8 Yellow/Black (Data) Immo. Data Interrupt (conn. side) [4] driver kick, white 43 pin plug, pin 10
This connection is not required in US vehicles without transponder
immobilizer.
data blue (EMS COM) Remote Start
Only
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) Parking Light Output headlight switch or BCM above gas pedal, gray 24 pin plg, pin 22 - pink Mandatory
H2/2 Blue/White (-) Ground When Running (Status) Output No Connection
H2/3 Dk. Green/Black (-) Lock Output No Connection
H2/4 Red/White (-) Trunk Release Output No Connection
H2/5 Brown/Black (-) Horn Output horn switch or driver kick, white 43 pin plug, pin 21 - white Optional
H2/6 Brown/White (-) RAP Off Output No Connection
H2/7 White (+) AUX 1 Output No Connection
H2/8 Violet/Black (+) AUX 2 Output No Connection
H2/9 Dk. Blue/Black (-) Unlock Output No Connection
H2/10 Lt. Blue/Black (-) Factory Alarm Disarrn Output No Connection
H2/11 Brown/Red (+) Siren Output [2] The siren is only required when enabling the security features during
module flashing.
Security Only
H2/12 Pink (+) Ignition Sense Input No Connection
H2/13 Violet (+) Door Input No Connection
H2/14 Brown (+) Brake Input No Connection
H2/15 White/Blue (-) Activation Input No Connection
H2/16 Red/Blue (-) Valet switch No Connection
H2/17 Black/White (-) E-Brake Input No Connection
H2/18 Orange/Black (+) Instant Alarm Input No Connection
H2/19 Blue (-) Trunk Input No Connection

10 933.HKHT1 3.25.195.3 2013 Hyundai Sonata
©2022 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/20 Green (-) Door Input No Connection
H2/21 Gray (-) Hood Switch Input [1] The installation of an aftermarket hood pin is only required on vehicles
that are not equipped with a factory hood pin or if not supported in
data.
H2/22 Violet/White (AC) Tach input No Connection
Main harness, 12-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H3/1 Blue/White Relay N.C. - Immo. Data Interrupt (vehicle side) [4] driver kick, white 43 pin plug, pin 10
This connection is not required in US vehicles without transponder
immobilizer.
data blue (EMS COM) Remote Start
Only
H3/2 Blue/Red Relay N.O. - No Connection No Connection
H3/3 Blue Relay COM - Immo. Data Interrupt (conn. side) [4] driver kick, white 43 pin plug, pin 10
This connection is not required in US vehicles without transponder
immobilizer.
data blue (EMS COM) Remote Start
Only
H3/4 White/Brown Relay N.C. - No Connection No Connection
H3/5 White Relay COM - No Connection No Connection
H3/6 Red (+) 12 Volt Input ignition switch, white 6 pin plug, pin 1 + green (30A) Mandatory
H3/7 Lt. Green/Red Relay N.O. - No Connection No Connection
H3/8 Lt. Green Relay COM - No Connection No Connection
H3/9 Lt. Green/White Relay N.C. - No Connection No Connection
H3/10 Black (-) Ground (chassis ground) Mandatory
H3/11 White Relay COM - No Connection No Connection
H3/12 Red (+) 12 Volt Input ignition switch, white 6 pin plug, pin 1 + green (30A) Mandatory
Relay harness, 10-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H4/1 N/A No Connection No Connection
H4/2 Red/Black (+) 12 Volt Input ignition switch, white 6 pin plug, pin 1 + green (30A) Remote Start
Only
H4/3 Pink/Black Flex Relay (pin 87a) No Connection
H4/4 Pink/White (+) Flex Relay Output No Connection
H4/5 Red (+) 12 Volt Input ignition switch, white 6 pin plug, pin 1 + green (30A) Remote Start
Only
H4/6 Green Starter Input (conn. side) [3] ignition switch, white 6 pin plug, pin 3
Connection required for Starter Disable ONLY.
+ yellow Mandatory
H4/7 Violet (+) Starter Output (vehicle side) [3] ignition switch, white 6 pin plug, pin 3 + yellow Mandatory
H4/8 Orange (+) Accessory Output ignition switch, white 6 pin plug, pin 2 + orange Remote Start
Only