Directed DS3+ User manual

Designed by Installers for Installers
INSTALLATION GUIDE
DS3+ / DS4+
2009 Toyota RAV4. 933.TL11 1.12.193.2
© 2019 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.

Introduction 4
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Key type 5
Installation 6
Wiring diagram with T-Harness (THTON10) 6
Wiring diagram 7
Locating components in the vehicle 8
Vehicle connections 9
Connecting the module 12
Important! 12
8556T Temperature Sensor 12
8504D Combo Sensor 12
RF Systems 13
When used in conjunction with SmartStart 13
D2D port configuration 13
Module programming 14
With transponder and CAN 14
Without transponder with CAN 15
Module programming for security-only installations 16
LED diagnostics and troubleshooting 17
Soft reset 19
Hard reset 19
Learning the Tach (not needed with Virtual Tach) 20
Initializing Virtual Tach (not needed with hardwired or data tach applications) 20
Limited lifetime consumer warranty 21
Quick reference guide 22
Contents

3933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.

4933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Introduction
DS3+ is a complete solution for remote start, security (when security features are enabled) and bypass. This guide provides
information on the installation of the module as a digital solution. Please refer to www.directechs.com for more information about
which configuration is best for your application.
Warning! This module can be configured using the web tool located at www.directechs.com. The DS3/DS3+ module is not
equipped with Bluetooth, therefore the blue LED will not flash during module programming or when performing a soft or hard reset.
DS4+ is a complete solution for remote start, security (when security features are enabled), bypass, and features
built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information on the
installation of the module as a digital solution. Please refer to the DirectLink application or www.directechs.com
for more information about which configuration is best for your application.
Warning! This module is designed to be configured using the DirectLink application for mobile devices,
however it can also be configured using the web tool located at www.directechs.com. To download the DirectLink mobile
application, please visit the Google Play or Apple store.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
DS4+/DS3+ Only
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
Accessory Activation
Ignition Activation
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
E-Brake Status
Ignition Status

5933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible THTON10 Keys required for programming 1Keys required for operation 0
Important: If your vehicle is NOT equipped with transponders or CANs, please flash your module with an Analog firmware.
This guide will help you with the installation diagram and vehicle connections.
Some Toyota 2010+ models have different encryption types. Please look at your key blade and indentify the markings.
A dot "." means the vehicle is compatible with TL11 firmware. "G" or "H" indicates the vehicle is not compatible with this
firmware. Refer to "Key Types" for more information.
The optional Plug & Play THTON10 T-Harness is sold separately.
The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.
All T-Harness wires NOT listed in the diagram are NOT required for the installation.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each
wiring diagram.
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] The Green wire is ONLY required for starter disable and antigrind applications.
[4] Second starter connection may be required in some vehicles.
Key type
Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings.
G-stamped keys Standard Key H-stamped keys
H
For vehicles with H-stamped keys, see
the TL10 firmware.
For vehicles with G-stamped keys, see
the TL5 & TL7 firmware.
For vehicles with dot-stamped keys,
see the TL11 firmware.

6933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram with T-Harness (THTON10)
(-) Parking Light Output: Lt.Green/Black
Siren
Hood Pin (-) Hood Input: Gray
(+) Siren Output: Brown/Red
Headlight Switch
(white 20-pin conn.)
12345678910
1112131415161720
19 18
(-) Parking Lights: Pin 18
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22-pin White Connector
8-pin White Connector
12-pin Black Connector
10-pin White Connector
Ignition Connector
Diagnostic Connector OBDII
THTON10
(optional T-Harness)
NOT USED
Transponder Key Amplifier
(black conn. around ignition)
Cut the
Violet/White loop
labelled TACH.
Cut the
Yellow/Black loop
labelled SIL.
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20
15

7933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram
(-) Ground: Black: 10
HS CAN Low: Tan : 1
(-) Parking Light Output: Lt.Green/Black: 1
HS CAN High: Tan/Black: 2
Data TX: Yellow/Black: 8
Data RX: Orange/Black: 7
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
(+) Starter 2 Output: Blue: 3
(+) 12V Input: Blue/Red: 2
(+) Ignition Input/Ouput: Pink: 10
(+) 12V Input: Red: 5
(+) 12V Input: Red/Black: 2
(+) Ignition 2 Output: Pink/White: 4
(+) 12V Input: Red/White: 9
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
OBDII Plug
Black Connector
HS CAN High: Pin 6
HS CAN Low: Pin 14
16
8
9
1
Refer to Vehicle Connections for wire and connector details.
Refer to Vehicle Connections
for wire and connector details.
Ignition Switch
Headlight Switch
(white 20-pin conn.)
12345678910
1112131415161720
19 18
(-) Parking Lights: Pin 18
Dash Fuse Box
(white 1-pin conn.)
1
Transponder Key Amplifier
(black conn. around ignition)
(+) Starter Output (veh. side): Violet: 7
Starter Input (conn. side): Green: 6
CUT
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
(+)Accessory Output: Orange: 8
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20

8933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Locating components in the vehicle

9933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2009 Toyota RAV4. Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low OBD-data link connector, white 16 pin plug, pin 14 data white Mandatory
H1/2 Tan/Black (Data) HS CAN High OBD-data link connector, white 16 pin plug, pin 6 data black Mandatory
H1/3 Orange/Brown No Connection No Connection
H1/4 Orange/Green No Connection No Connection
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown No Connection No Connection
H1/7 Orange/Black (Data) Immo Data Transponder Key Amplifier on key switch, black 7 pin plug, pin
4
data pink Remote Start
Only
H1/8 Yellow/Black (Data) Immo Data Transponder Key Amplifier on key switch, black 7 pin plug, pin
5
data green Remote Start
Only
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) Pk Light Output headlight switch, white 20 pin plug, pin 18 - white Mandatory
H2/2 Blue/White No Connection No Connection
H2/3 Dk. Green/Black No Connection No Connection
H2/4 Red/White No Connection No Connection
H2/5 Brown/Black No Connection No Connection
H2/6 Brown/White No Connection No Connection
H2/7 White (+) No Connection No Connection
H2/8 Violet/Black No Connection No Connection
H2/9 Dk. Blue/Black No Connection No Connection
H2/10 Lt. Blue/Black No Connection No Connection
H2/11 Brown/Red (+) Siren Output [2] Security Only
H2/12 Pink No Connection No Connection
H2/13 Violet No Connection No Connection
H2/14 Brown No Connection No Connection
H2/15 White/Blue No Connection No Connection
H2/16 Red/Blue No Connection No Connection
H2/17 Black/White No Connection No Connection
H2/18 Orange/Black No Connection No Connection
H2/19 Blue No Connection No Connection
H2/20 Green No Connection No Connection
H2/21 Gray (-) Hood Switch Input [1] Not Applicable

10 933.TL11 1.12.193.2 2009 Toyota RAV4
© 2019-11-22 Directed. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/22 Violet/White No Connection No Connection
Main harness, 12-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H3/1 Blue/White Relay N.C. No Connection No Connection
H3/2 Blue/Red Relay N.O. (+) 12 Volt Input ignition switch, white 8 pin plug, pin 7 + blue (30A) Remote Start
Only
H3/3 Blue Relay COM (+) Start 2 Output ignition switch, white 8 pin plug, pin 1 + white Remote Start
Only
H3/4 White/Brown Relay N.C. No Connection No Connection
H3/5 White Relay COM No Connection No Connection
H3/6 Red (+) 12 Volt Input ignition switch, white 8 pin plug, pin 7 + blue (30A) Mandatory
H3/7 Lt. Green/Red Relay N.O. No Connection No Connection
H3/8 Lt. Green Relay COM No Connection No Connection
H3/9 Lt. Green/White Relay N.C. No Connection No Connection
H3/10 Black (-) Ground (chassis ground) Mandatory
H3/11 White Relay COM No Connection No Connection
H3/12 Red (+) 12 Volt Input ignition switch, white 8 pin plug, pin 7 + blue (30A) Mandatory
Relay harness, 10-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H4/1 N/A No Connection No Connection
H4/2 Red/Black (+) 12 Volt Input ignition switch, white 8 pin plug, pin 7 + blue (30A) Remote Start
Only
H4/3 Pink/Black No Connection No Connection
H4/4 Pink/White (+) Ignition 2 Output ignition switch, white 8 pin plug, pin 4 + pink Remote Start
Only
H4/5 Red (+) 12 Volt Input ignition switch, white 8 pin plug, pin 7 + blue (30A) Remote Start
Only
H4/6 Green Starter Input (conn. side) [3] ignition switch, white 8 pin plug, pin 8
Connection required for Starter Disable Only.
+ yellow Mandatory
H4/7 Violet (+) Starter Output (vehicle side) ignition switch, white 8 pin plug, pin 8 + yellow Mandatory
H4/8 Orange (+) Accessory Output ignition switch, white 8 pin plug, pin 3 + red Remote Start
Only
H4/9 Red/White (+) 12 Volt Input ignition switch, white 8 pin plug, pin 7 + blue (30A) Remote Start
Only
H4/10 Pink (+) Ignition Input/Output ignition switch, white 8 pin plug, pin 6 + white Mandatory