Ditel Kosmos series User manual

JR-P / JR20-P
KOSMOS SERIE www.ditel.es
USER MANUAL
UNIVERSAL DIGITAL INDICATOR
FOR PROCESS, TEMPERATURE
AND RESISTANCE INPUT SIGNAL
JUNIOR JR-P / JR20-P

JR-P / JR20-P
KOSMOS SERIE 2
INDEX
GENERAL INFORMATION
Package contents ........................................................................................................... 4
Recycling instrucctions .................................................................................................... 4
General safety considerations .......................................................................................... 4
Symbols identification .................................................................................................. 4
Maintenance ................................................................................................................... 5
Warranty ....................................................................................................................... 5
Conformity declaration .................................................................................................... 6
Device description .......................................................................................................... 7
Dimensions and mounting ............................................................................................... 7
Display and keyboard ..................................................................................................... 8
Installing and connecting recommendations ..................................................................... 8
Connections ................................................................................................................... 9
Process input (V) ......................................................................................................... 9
Process input (mA) .................................................................................................... 10
Potentiometer input ................................................................................................... 10
Pt100 and Pt1000 sensor input ................................................................................... 11
Thermocouple (J, K, T and N) input ............................................................................. 11
Resistance input ........................................................................................................ 11
Relays output ............................................................................................................ 11
INPUT CONFIGURATION
Configuration menu ....................................................................................................... 12
Input configuration ....................................................................................................... 12
Process ........................................................................................................................ 13
Temperature ................................................................................................................ 13
Potentiometer .............................................................................................................. 13
Resistance ................................................................................................................... 14
DISPLAY CONFIGURATION
Display programming .................................................................................................... 15
Display scaling ............................................................................................................. 15
Process input ............................................................................................................. 16
Temperature input ..................................................................................................... 16
Potentiometer input ................................................................................................... 17
Resistance input ........................................................................................................ 17
SETPOINTS CONFIGURATION
Setpoints configuration ................................................................................................. 18
AVAILABLE KEYBOARD FUNCTIONS
MAX/MIN and RESET functions ...................................................................................... 19
Direct access to setpoints value ..................................................................................... 19
Return to default configuration ...................................................................................... 19
Access to lock-out configuration menu ........................................................................... 20
CONFIGURATION LOCK-OUT
Lock-out menu ............................................................................................................. 21
OUTPUT OPTION
Description ................................................................................................................... 23
Function modes description ........................................................................................... 23
HI/LO mode activation ............................................................................................... 23
Time delay ................................................................................................................ 23
Asymmetrical hysteresis ............................................................................................. 23
Installation ................................................................................................................... 24

JR-P / JR20-P
KOSMOS SERIE 3
INDEX
SPECIFICATIONS
Technical specifications ................................................................................................. 25

JR-P / JR20-P
KOSMOS SERIE 4
GENERAL INFORMATION
With the instrument it is also supplied:
 Quick installation guide.
 Mounting panel accessories (a sealing gasket and 2 fixing clips).
 Wiring accessories (plug-in terminal block connectors and 2 key tools for cable insertion).
 4 adhesive labels set with engineering units.
Package contents
This manual does not constitute a contract or a commitment on the part of Diseños y Tecnología, S.A.
All information contained in this document is subject to change without prior notice.
MANUAL VALID FOR INSTRUMENTS WITH P2.02 SOFT VERSION OR HIGHER
This electronic instrument is covered by the 2002/96/CE European Directive so, it is properly marked with
the crossed-out wheeled bin symbol that makes reference to the selective collection for electrical and
electronic equipment which indicates that at the end of its lifetime, the final user cannot dispose of it as
unsorted municipal waste.
In order to protect the environment and in agreement with the European legislation regarding waste of
electrical and electronic equipments from products put on the market after 13 August 2005, the user can
give it back, without any cost, to the place where it was acquired to proceed to its controlled treatment and
recycling.
Recycling instructions
General safety considerations
Symbols identification
WARNING: Risk of electric shock.
Instrument protected by double isolation or reinforced isolation.
All instructions and guidelines for the installation and manipulation that are present in this manual must be considered
to ensure personal safety and to prevent damage to either the instrument or any equipment connected to it.
Safety of any equipment incorporated to this instrument is responsibility of the system installer.
If this electronic indicator is used in a manner not specified by the manufacturer in this manual, the protection
provided by the instrument may be impaired.
WARNING: Potential risk of danger.
Read completely related instructions when this symbol appears in order to know the potential risk and to
know how to avoid it.

JR-P / JR20-P
KOSMOS SERIE 5
All products are warranted against defective material and workmanship for a period of three years from
acquisition date.
If a product appears to have a defect or fails during the normal use within warranty period, please
contact the distributor from whom you purchased the product to be given proper instructions.
This warranty does not apply to defects resulting from action of the customer such as mishandling or
improper interfacing.
The liability under this warranty shall extend only to the repair of the instrument; no responsability is
asumed by the manufacturer for any damage which may result from its use.
All DITEL products benefit from an unlimited and inconditional warranty of three (3) years from the date
of their purchase. Now you can extend this period up to five (5) years from the product commissioning,
only by fulfilling the corresponding form.
Warranty
Maintenance
To guarantee instrument accuracy, it is recommended to checking its compliance according to the technical
specifications listed in this manual, performing calibrations regularly in accordance to operation criteria in each
application.
Instrument calibration and/or adjustment should be performed only by an accredited laboratory or directly by the
manufacturer.
Instrument repairs should only be carried out by the manufacturer or by its authorized partners.
For frontal device cleaning, just wipe it with a damp cloth and neutral soap product. DO NOT USE SOLVENTS!.

JR-P / JR20-P
KOSMOS SERIE 6
Conformity declaration
EN 61326-1Electrical equipment for measurement, control and
laboratory use (EMC)
EN 61000-4-2Electrostatic discharge (ESD) Criterion B
Air discharge 8kV
Contact discharge 4kV
EN 61000-4-3Electromagnetic fields Criterion A
10 V/m
EN 61000-4-4Fast transients (burst) Criterion B
Power lines 2 kV
Signal lines 1 kV
EN 61000-4-5Surge Criterion B
1 kV L to N
2 kV L,N to Earth
1 kV Signal lines to Earth
EN 61000-4-6RF conducted interference Criterion A
3 Vrms
EN 61000-4-11 Voltage dips:
0% V during 1 cycle Criterion B
40% V during 10/12 cycles Criterion C
70% V during 25/30 cycles Criterion C
Short interruptions:
0% V during 250/300 ciclos Criterion C
CISPR11 Emission limits
Class B
EN 61010-1 Safety requirements for electrical equipment
for measurement, control an laboratory use.
General safety
Overvoltage category II
Pollution degree 2
Conductive pollution excluded
Isulation type:
Enclosure: Double
Power/signal/relays: Basic

JR-P / JR20-P
KOSMOS SERIE 7
All information contained in this manual, unless indicated, is valid for both JR-P and JR20-P models.
JR-P and JR20-P models from KOSMOS serie are universal digital indicators fully configurables that
allow input type selection in order to be used as needed. Available signal inputs are the following:
PROCESS (V, mA)
THERMOCOUPLE (J, K, T y N)
Pt100 and Pt1000 SENSOR
POTENTIOMETER
RESISTANCE
The basic instrument consists of a soldered assembly composed of a main board, a display and an input signal
circuits. It can also be incorporated, as an option, an extra plug-in 2 SPDT 8A relays circuit output which is isolated
from signal input and power supply. This extra circuit has independent connectors that are located on the rear part
of the instrument once it is installed.
Specially designed for the control of industrial processes and monitoring input variables, both models have 4 digits,
configurable decimal point and 2 LED’s for setpoints status indication, they are easy to scale into desired
engineering units, directly by frontal keys or rear input signal value in teach mode. They also provide a 24V DC
output for sensor excitation.
JR-P model is provided with 14mm-high digits and maximum display range of -9999 to 9999 whereas
JR20-P has 20mm-high digits and a maximum range of -1999 to 9999. JR20-P has a larger display to
provide a better reading at longer distance, although minus LED sign is integrated in the most significative digit
instead of being external, as in JR-P model.
Both devices have three frontal keys to interact with internal software and set configuration in order to adapt their
function to particular applications. Device programming runs through some independent menus that show short
messages to easily identify input type and/or display configuration steps.
If relays output option card is installed, once it is recognised by the instrument, activates its own configuration
menu which is only visible under this conditions.
Device description
Dimensions and mounting
To install the instrument, prepare a
92x45mm panel cut-out and slide the unit
inwards making sure of placing the sealing
gasket between the front side panel and
the frontal bezel.
While holding the unit in place, put the
fixing clips on both sides of the case and
slide them through the guide tracks until
they reach the panel at the rear side.
Press slightly to fasten the clips to the latching slots
on the case and get the unit fully assembled and
close fitted to achieve a good sealing.
To remove the instrument from the panel, pull outwards the rear fixing
clips latching tabs until they are disengaged, then slide fixing clips back
over the case.

JR-P / JR20-P
KOSMOS SERIE 8
Display and keyboard
12
1
2
4
5 6 7 8
9
UP SHIFT DATA
ENTER
3
RUN MODE PRO MODE
14 red digit Display Shows value according configuration. Shows steps and data during configuration.
2Minus sign LED (only for JR-P) It iluminates for negative readings. It iluminates for negative values.
3Keyboard ——
4Setpoint 1 LED It iluminates when Setpoint 1 turns active. It iluminates when Setpoint 1 turns active.
5UP key No application. Shows Setpoints value.
Increases value of active digit.
6SHIFT key Displays maximum and minimum stored values. After 3s of pressing, sets maximum and/or minimum
memorized value to current display value.
Shifts active digit to the next right digit.
Shows sequentially menu options.
7DATA/ENTER key Changes to PRO mode. Validates selected data and parameters. Moves one step forward in configuration menu.
Changes to RUN mode.
8Setpoint 2 LED It iluminates when Setpoint 2 turns active. It iluminates when Setpoint 2 turns active.
9Free space for units label ——
There are two main function modes:
RUN and PRO. PRO mode is w hen
configuration menu is entered to
programm the indicator, whereas
RUN is the normal mode in w hich
display shows the reading according
to configuration and input signal
value.
The table below summarizes display
parts description and LEDs and
keyboard function.
Installing and connecting recommendations
WARNING: If this instrument is not installed and used in accordance with this instructions,
the protection provided by it against hazards may be impaired.
To meet the requirements of EN 61010-1 standard, where the unit is permanently connected to main
supply, its is obligatory to install a circuit breaking device easy reachable to the operator and clearly
marked as the disconnecting device.
To guarantee electromagnetic compatibility, the following guidelines should be kept in mind:
 Power supply wires should be separatedly routed from signal wires and never runned in the same
conduit.
 Use shielded cable for signal wiring.
 Cables section should be  0.25 mm².
Before connecting signal wires, signal type and input range should be verified to be within the right
limits. Do not connect simultaneously more than one input signal to the meter.
This instrument coforms with the following community directives: EMC 2004/108/CE and LVD 2006/95/CE.
Refer to the instructions in this manual to preserve safety protections.

JR-P / JR20-P
KOSMOS SERIE 9
Connections
Basic instrument has two rear connectors CN1 and CN2. If 2RE
output option card is installed, two more connectors CN3 and CN4
appear. See all four connectors location and their pin out in the
right figure. All female provided terminal connectors are of CAGE
CLAMP® technology.
Terminals for CN2 connector admit cables with section from
0.2mm² up to 1.5mm² (AWG 24÷14).
Terminals for CN1, CN3 and CN4 connectors admit cables
with section from 0.08mm² up to 2.5mm² (AWG 28÷12).
To perform wiring connections, strip the cable leaving from 7 to
10mm exposed to air, insert it in the proper terminal while
pushing down the key insertion tool to open the clip inside the
connector. Release the key tool to fix wire to the terminal.
Proceed in the same way for the rest of terminals. Once all
connections are done, plug connectors to the instrument.
Rear connectors location.
Key tool for cable insertion.
Process input signal wiring diagrams (V)
CN2
1COMMON / Pt100 / Pt1000 / -TC / Pot. Term. 1
2Pt100 / Pt1000 / +TC / IN 1k-10k / Pot. Cursor
3IN 50k / Pot. Term. 2
4Common Pt100
5+mA
6+EXC. 24V / 10V (*)
7+V
CN1*
1Phase (AC)
2Neutral (AC)
Notes:
NO: Normally open contact.
CM: Common contact.
NC: Normally closed contact.
* Polarity in CN1 is indistinct for DC power.
CN3
1 2
CN2 CN1
CN4
1
2
3
4
5
6
CN3 (relay
1)
1NO
2CM
3NC
CN4 (relay
2)
4NO
5CM
6NC
4 WIRES CONNECTION WITH EXTERNAL EXCITATION 4 WIRES CONNECTION WITH EXCITATION SUPPLIED BY THE INDICATOR
INDICATOR TRANSDUCER
EXC.
17
COM. +V
+OUT-OUT -EXC.+EXC.
0-10V
0-200V
+-
INDICATOR TRANSDUCER
17
COM.
+V
+OUT -OUT -EXC. +EXC.
0-10V
0-200V
6
+EXC.
WARNING
Isolation:
1500Vrms for 1 minute to signal terminals (CN2) and power terminals (CN1).
2500Vrms for 1 minute to signal terminals (CN2) and relays terminals (CN3 y CN4).
2500Vrms for 1 minute to power terminals (CN1) and relays terminals (CN3 y CN4).
(*) SELECTION OF SENSOR EXCITATION
Set jumper to desired position 10V or 24V.
(Default 24V)

JR-P / JR20-P
KOSMOS SERIE 10
3 WIRES CONNECTION WITH EXTERNAL EXCITATION 3 WIRES CONNECTION WITH EXCITATION SUPPLIED BY THE INDICATOR
INDICATOR TRANSDUCER
EXC.
17
COM.
+V
+EXC.
0-10V
0-200V
+-
INDICATOR TRANSDUCER
17
COM.
+V
+EXC.
0-10V
0-200V
6
+EXC.
+OUT -OUT +OUT -OUT
Process input signal wiring diagrams (mA)
4 WIRES CONNECTION WITH EXTERNAL EXCITATION 4 WIRES CONNECTION WITH EXCITATION SUPPLIED BY THE INDICATOR
3 WIRES CONNECTION WITH EXTERNAL EXCITATION 3 WIRES CONNECTION WITH EXCITATION SUPPLIED BY THE INDICATOR
2 WIRES CONNECTION WITH EXTERNAL EXCITATION 2 WIRES CONNECTION WITH EXCITATION SUPPLIED BY THE INDICATOR
INDICATOR TRANSDUCER
1
COM.
+mA
+OUT -OUT -EXC. +EXC.
0-20mA
4-20mA
5
EXC.
+-
INDICATOR TRANSDUCER
1
COM.
+mA
+OUT -OUT +EXC.
0-20mA
4-20mA
5
EXC.
+-
INDICATOR TRANSDUCER
1
COM.
+mA
+OUT +EXC.
4-20mA
5
EXC.
+-
INDICATOR TRANSDUCER
1
COM.
+mA
+OUT -OUT -EXC. +EXC.
0-20mA
4-20mA
56
+EXC.
INDICATOR TRANSDUCER
1
COM.
+mA
+OUT -OUT +EXC.
0-20mA
4-20mA
56
+EXC.
INDICATOR TRANSDUCER
+mA
+OUT +EXC.
4-20mA
56
+EXC.
Potentiometer input wiring diagram ()
INDICATOR POTENTIOMETER
1
TERM.2 TERM.1
2
CURSOR
3
TERM.2
TERM.1
CURSOR
NOTE:
Do not perform measurements with potentiometer
subjected to external voltage, since it may interfere in
the measure, altering the reading and even cause
serious damages on this unit.

JR-P / JR20-P
KOSMOS SERIE 11
Pt100 and Pt1000 sensor input wiring diagram (ºC)
INDICATOR Pt100 SENSOR
124
Pt100 COM.
Pt100
Pt100
INDICATOR Pt1000 SENSOR
12
Pt1000
Pt1000
Thermocouple J, K, T and N input wiring diagram (ºC or ºF)
INDICATOR
12
+TC
-TC
+-
J,K,T,N
Relays output wiring
INDICATOR
13
50k
COM.
50k MÁX. INDICATOR
12
10k
COM.
10k MÁX.
Resistance input wiring diagram ()
NOTE:
Do not perform measurements with resistance subjected to external voltage, since it may interfere in the measure,
altering the reading and even cause serious damages on this unit.
RELAY 2 RELAY 1
4
5
6
1
2
3
NO
CM
NC
NO
CM
NC IMPORTANT:
To guarantee electrical safety according to EN 61010-1 a
protective 8A/250V external fuse must be installed.
8A/250V MAX.
WARNING:
Read recommendations and related data on pages 8 and 9.

JR-P / JR20-P
KOSMOS SERIE 12
INPUT CONFIGURATION
When connecting instrument to Power supply, display test begins automatically to check the good function of LED’s
and digits, once this test is finished, display shows internal software version and then the unit goes to RUN mode.
Configuration software has a hierarchical structure composed of a number of menus and submenus. By pressing
ENTER key, display show s “Pro”, a new pressing brings access to main menu where appear configuration
menus, that is, input configuration (InP), display configuration (dSP) and setpoints configuration (SEtP). This last
menu only appears if 2RE output option card is installed.
If configuration is totally locked-out, when pressing ENTER key to get into main menu, display shows “dAtA”
instead of “Pro”. This indicates that it is only possible to see programmed information and that it is not allowed to
modifiy any parameter from the entire configuration. In this visualization mode, the instrument automatically
switches back to RUN mode after 15 seconds since last key press.
Configuration menu
The instrument provides 3 keys for progressing through the
menus and submenus and for data introducing/modifying:
ENTER: Vertical displacement / Validates data.
UP: Increases active digit value.
SHIFT: Horizontal displacement / Changes active digit.
Input configuration
The first menu corresponds to input configuration. This, in turn, consists of four submenus, one for each input
type: process (ProC), temperature (tEMP), potentiometer (Pot) and resistance (rES).
Once inside each menu, all configuration parameters are sequentially shown and they can then be introduced or
edited by pressing ENTER key. Numeric values must be entered digit by digit, first selecting digit and then
changing its value. When the display reach desired value, a new ENTER key pressing validates data and routine
goes forward to next configuration step.
Data entered or changes made during configuration are stored in device memory only when programmation
routine belonging to the respective submenu is completed, not before. On last routine step and after having
pressed ENTER key, display indicates “StorE” and the unit goes back again to RUN mode.
8 8 8 8
Pro dAtA
InP dSP SEt
MAIN MENU
InP
ProC tEMP Pot rES

JR-P / JR20-P
KOSMOS SERIE 13
Process
INPUT TYPE:
V DC: ±10V or ±200V (-tachometric dynamo-)
A DC: ±20mA (single range, direct
validation)
ProC
-U-
10U 200U
-A-
Temperature
tEMP
SENSOR TYPE:
tC:Termocouple J(1), K(2), T(3) or N(4)
Pt1:Pt100 sensor (direct validation)
Pt2:Pt1000 sensor (direct validation)
tC
-1- -4-
Pt1 Pt2
The parameters to be configured in input process
submenu are:
The parameters to be configured in input
temperature submenu are:
RESOLUTION TYPE:
1ºC:Celsius degrees
0.1ºC:Tenths of degree Celsius
1ºF:Fahrenheit degrees
0.1ºF:Tenths of degree Fahrenheit
1ºC 0.1ºC 1ºF 0.1ºF
oFS
00.0
Potentiometer
No additional configuration is needed for this input type (direct validation).
Pot
DISPLAY OFFSET :
Configurable value:
-9.9 to +9.9 display counts if a tenths of degree resolution is selected
-99 to +99 display counts if a degree resolution is selected
Usually it will not be necessary to introduce any offset value, except in cases where a
known difference between temperature captured by the sensor and real temperature
should be compensated.

JR-P / JR20-P
KOSMOS SERIE 14
Resistance
rES
999.99999 50.00
RESISTANCE RANGE:
999.9:999.9 (1k) Range
9999:9999 (10k) Range
50.00:50.00k (50k) Range
The only parameter to be configured in input
temperature submenu is:

JR-P / JR20-P
KOSMOS SERIE 15
DISPLAY CONFIGURATION
dSP
SCAL tEAC FiLt
Display Programming
Display scaling
IMPORTANT IN “tEAC” MODE:
To ensure the best accuracy, both points 1 and 2
should represent extreme process limits.
The second menu corresponds to display configuration. This, in turn, consists of some submenus according to
previously programmed input type: through frontal keys configuration (SCAL or uSEr), through real input signal
(TEACH) (tEAC), calibrated range (CAL) and reading stabilization filter (FiLt).
TRHOUGH FRONTAL KEYS CONFIGURATION “SCAL”
Input and display values are configured manually through
the three keys of the instrument. This method is
suitable when signal values supplied by the transducer at
each extreme point of the process are known.
REAL INPUT SIGNAL CONFIGURATION “tEAC”
Input values are directly introduced from CN2 input
connector just at the moment of signal capturing at
each point of the process. Display values are
configured manually through the three keys, as in the
previous case. This method is suitable when signal values at
each point are unknown but, it is possible to lead process to
the conditions defined by these extreme points.
WEIGHTED AVERAGE FILTER “FiLt”
Sets low-pass filter cutoff frequency (Fc) which allows the instrument to smooth out undesirable display reading
fluctuations.
Display scaling is necessary when adapting display reading to a particular engineering unit. Display range can be
configured between -9999 and 9999 for JR-P (14mm-high digits) or between -1999 and 9999 for JR20-P
(20mm-high digits).
Display scaling is a linear process that consists in introducing two input values, referred as Input 1 and Input 2,
and their respective display values, referred as Display 1 and Display 2. On the basis of this proportional
relationship internal software calculates display value that would correspond to a given input value. Decimal point
position would complete required engineering units indication.
It is possible to scale display in an increasing or decreasing proportional mode depending on whether if second
display value (DISP.2) is greater or less than the first (DISP.1). In an increasing mode, display value increases
proportionally to the input value whereas in a decreasing mode, display value decreases. The left figure below
shows both scaling modes.
The right figure shows an
example for a 10 bar pressure
sensor with a 4-20mA output
signal. Decimal point is
situated between second and
third digit of the display.
(10.00)
DISP.2
(00.00)
DISP.1
(04.00)
INP.1
(20.00)
INP.2
Increasing proportional mode Decreasing proportional mode
DISPLAY 2
DISPLAY 1
DISPLAY 1
DISPLAY 2
INPUT 1 INPUT 2 INPUT 1 INPUT 2

JR-P / JR20-P
KOSMOS SERIE 16
Process input
FIRST POINT INPUT AND DISPLAY VALUE:
InP1:Input value indication.
0000:Value entering in counts within available model display range.
dSP1: Display value indication.
0000:Value entering in counts within available model display range.
DECIMAL POINT:
00.00:Setting of decimal point position.
(Decimal point can be located in any position, and will be
the same for Display 1 and Display 2. This position remains
fixed for all configuration steps and also for RUN mode).
SECOND POINT INPUT AND DISPLAY VALUE:
InP2:Input value indication.
0000:Value entering in counts within available model display range.
dSP2: Display value indication.
0000:Value entering in counts within available model display range.
Temperature input
When programmed input type is temperature, for thermocouple and Pt100 or
Pt1000 sensor, the only parameter to configure is the filter and its configuration
is done in the same way as described for process input.
Display scaling is not available for this input type, the unit then will assume a
fixed calibrated range depending on sensor type and previously configured units
resolution.
FiLt
0
FiLt
0
SCAL
InP1
tEAC
0000
dSP1
0000
00.00
InP2
0000
dSP2
0000
When programmed input type is process, for both display scaling
“SCAL” and “tEAC” methods, parameters to be sequentially introduced
are identical.
It only must be considered that in “SCAL” method, all values must be
manually introduced through the three frontal keys whereas in “tEAC”
method, input signal value must be present at the conector at each
point that is intended to be configured.
WEIGHTED AVERAGE FILTER:
FiLt:0 to 9 configurable
Value Fc (Hz) Value Fc (Hz)
0-- 52.2
17.3 61.6
25.1 71.1
33.8 80.5
42.9 90.2

JR-P / JR20-P
KOSMOS SERIE 17
Potentiometer input
FIRST POINT DISPLAY VALUE:
dSP1:Display value indication.
0000:Value entering in counts within available model display range.
(potentiometer cursor must correspond to process first point).
DECIMAL POINT:
00.00:Setting of decimal point position.
(Decimal point can be located in any position, and will be the same for
Display 1 and Display 2. This position remains fixed for all configuration
steps and also for RUN mode).
SECOND POINT DISPLAY VALUE:
dSP2:Display value indication.
0000:Value entering in counts within available model display range.
(potentiometer cursor must correspond to process second point).
FiLt
0
tEAC
dSP1
0000
00.00
dSP2
0000
Resistance input
SCAL tEAC FiLt
uSEr CAL
When programmed input type is potentiometer, “tEAC” is the only method available
to perform display scaling.
In this case, it must be assured first that potentiometer is connected properly and
that it is not subjected to any external voltage.
After pressing ENTER key, the instrument analyzes connected potentiometer to
internally determine both maximum and minimum resistive values. Once this
calculation have finished, display shows “dSP1”.
WEIGHTED AVERAGE FILTER:
FiLt:0 to 9 configurable.
Value Fc (Hz) Value Fc (Hz)
0-- 52.2
17.3 61.6
25.1 71.1
33.8 80.5
42.9 90.2
When programmed input type is resistance, display scaling (“uSEr”) and also working as a fixed calibrated range
(“CAL”) depending on the resistance range previously configured are available.
Display scaling is possible through frontal keys (“SCAL”) and through real input signal (“tEAC”) as described for
process input. If the fixed calibrated range option “CAL” is selected, the programming routine goes directly to the
filter configuration (“FiLt”) with no option to return to scaling configuration.
Filter configuration is done in the same way as described for process input.

JR-P / JR20-P
KOSMOS SERIE 18
Setpoints configuration
SEtP
SEt1 SEt2
Hi Lo
no nc
dLy HyS
00.0 00.00
SETPOINT VALUE:
00.00:Value entering in counts within available model display range.
(Is not possible to change decimal point position, which is
the previously defined in display configuration menu).
ACTIVATING MODE:
Hi:High level relay activation.
Lo:Low level relay activation.
RESTING CONTACTS STATE:
no:Normally open contact.
nc:Normally closed contact.
TIME DELAY AND HYSTERESIS:
dLy:Programmable delay from 0 to 99.9s.
HyS:Hysteresis in counts within available model display range.
00.00
SETPOINTS CONFIGURATION
If 2RE output option card is uninstalled, the instrument keeps setpoints last configuration in memory, though it can
not be visualized.
Thanks to this feature there will be no need to reconfigure relays setting when 2RE output option is again installed
if the same configuration is required.
The third menu “SEtP” only appears when two relays output card is
installed. For further details on function modes please refer to the
corresponding OUTPUT OPTION part later on this manual.
Programming steps are equal for both relays on each “SEt1” and
“SEt2” submenus. The parameters to be configured are the following:

JR-P / JR20-P
KOSMOS SERIE 19
MAX/MIN and RESET functions
AVAILABLE KEYBOARD FUNCTIONS
Direct access to setpoints value
Pro
SEt1
00.00
SEt2
00.00
FIRST SETPOINT VALUE:
SEt1:Setpoint 1 value indication.
00.00:Value entering in counts within available model display range.
SECOND SETPOINT VALUE:
SEt2:Setpoint 2 value indication.
00.00:Value entering in counts within available model display range.
To access this menu from RUN mode, press ENTER key and while display shows
“Pro” press again ENTER for at least 3 seconds.
Display shows now “00” and ‘74’ code must be introduced through SHIFT and UP
keys.
Finally press ENTER to validate configuration and back to RUN mode.
Return to default configuration
5s
Pro
00
74
In addition to already known functions used to browse through the configuration menus and submenus, introduce
and/or modify existing values and parameters, the instrument provides some more added functions.
This device detects and stores in memory maximum and minimum values reached by the input signal. This values
are kept in memory although power supply is desconnected. When pressing repeatedly SHIFT key, MAX/MIN
function shows saved maximum and minimum values in display since last RESET function activation.
In order to differentiate this values indication from a mode RUN indication, decimal point blinks during the time
these values are shown. The unit automatically switches back to RUN mode after 15 seconds have elapsed since
the last key press.
First SHIFT key pressing shows “MAH” in display followed by the maximum value, a second pressing now shows
“Min” followed by the minimum value and finally, a third pressing shows “run” to back again in an instant to RUN
mode.
RESET function activates when visualizing maximum or minimum values SHIFT key is pressed for at
least 3 seconds. If maximum is the displayed value, current input signal value will replace the previous maximum
saved value. In the same way, current input signal will replace saved minimum value while is the minimum the
displayed value.
If 2RE output option is installed, it is possible to access to setpoints value
configuration without having to enter main menu.
To access this submenu, from RUN mode and after ENTER key is pressed, simply
press UP key while “Pro” is displayed.

JR-P / JR20-P
KOSMOS SERIE 20
Access to lock-out configuration menu
8888
CodE
0000
To access this menu from RUN mode, press ENTER key for at least 3 seconds.
Display shows now “CodE” and then “0000”. Desired security code must be introduced
through SHIFT and UP keys (by default this code is 0000).
Finally press ENTER to begin with lock-out level configuration. If entered security code
is wrong, the instrument will go back to RUN mode.
3s