DMP Electronics XR2400F User manual

XR2400F Addressable Fire Alarm Control
Panel
Installation Guide
238 Zone Fire Alarm Control Panel with Built-in Communicator
LT-0554 (12/00)
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products

MODEL XR2400F
Addressable Fire Alarm Control Panel
INSTALLATION GUIDE
FCC NOTICE
Thisequipmentgeneratesandusesradiofrequencyenergyand,ifnotinstalledandusedproperlyinstrictaccordancewith
the manufacturer's instructions, may cause interference with radio and television reception. It has been type tested and
found to comply with the limits for a Class B computing device in accordance with the specification in Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
Ifthisequipmentdoescauseinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipment
off and on, the installer is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the compute into a different outlet so that computer and receiver are on different branch circuits
Ifnecessary,theinstallershouldconsultthedealeroranexperiencedradio/televisiontechnicianforadditionalsuggestions.
The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:
"How to identify and Resolve Radio-TV Interference Problems."
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402
Stock No. 004-000-00345-4
Copyright ©2000 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

Table of Contents
Section Page
Introduction.....................................................................................................1
1.1Overview.......................................................................................1
1.2System Components.....................................................................1
1.3Power Specifications.....................................................................1
1.4Before you begin...........................................................................1
1.5About this guide............................................................................1
1.6How to use this guide....................................................................1
Mounting..........................................................................................................2
2.1Mounting the enclosure................................................................2
2.2Surface mounting..........................................................................2
2.3Flush mounting..............................................................................2
2.4The Fire Command Center LCD Keyboard...................................2
2.5Wiring diagram..............................................................................3
AC Connection................................................................................................4
3.1Transformers and AC Power Connection......................................4
3.228 VAC Transformer......................................................................4
3.316.5 VAC Transformer...................................................................5
3.4Earth ground from the XR2400F panel........................................5
Secondary Power Supply...............................................................................5
4.1Description....................................................................................5
4.2Battery Connection to XR2400F Command Processor panel......5
4.3Battery Connection to the 504-24 Power Supply.........................5
Two 866 NAC Modules....................................................................................6
5.1Description....................................................................................6
5.2Connection....................................................................................6
5.3Bell Silence/Bell Trouble................................................................6
5.4Notification Appliances..................................................................7
462N LX-Bus™ Expansion Card....................................................................8
6.1Description....................................................................................8
6.2LX-Bus™ Expansion Capability....................................................8
6.3Installing the 462N module...........................................................8
Telephone RJ Connector...............................................................................9
7.1Description....................................................................................9
7.2FCC registration............................................................................9
7.3Notification....................................................................................9
7.4Ground start..................................................................................9
893A Dual Phone Line Module......................................................................9
8.1Description....................................................................................9
8.2Connection....................................................................................9
8.3Jumper Settings..........................................................................10
8.4Digital Dialer/Multiplex.................................................................10
8.5Phone Line Monitor.....................................................................10
8.6Processor Fail Buzzer.................................................................10

504-24 Power Supply .................................................................................... 10
9.1 Description .................................................................................. 10
9.2 LED's........................................................................................... 10
9.3 504-24 Condition Chart............................................................... 11
9.4 504-24 UL Listings ...................................................................... 11
9.5 24 VDC NAC Standby Battery Calculations ............................... 11
9.6 Connection .................................................................................. 11
Interconnect Wiring Harness ...................................................................... 12
10.1 Interconnect Harness.................................................................. 12
Fire Command Center .................................................................................. 13
11.1 Description .................................................................................. 13
11.2 Connection .................................................................................. 13
11.3 Remote Fire Command Center................................................... 13
XR2400F Command Processor Panel......................................................... 14
12.1 Description .................................................................................. 14
12.2 Connection .................................................................................. 14
XR2400F Product Specifications ................................................................ 15
13.1 Power supply............................................................................... 15
13.2 Communication ........................................................................... 15
13.3 Panel zones................................................................................. 15
13.4 Remote Annunciator ................................................................... 15
13.5 LX-Bus™..................................................................................... 15
13.6 Outputs........................................................................................ 15
Expansion...................................................................................................... 16
14.1 Expansion zones......................................................................... 16
14.2 Output (relay) expansion............................................................. 16
Accessory Devices....................................................................................... 17
15.1 Wiring diagram ............................................................................ 17
15.2 Lightning protection..................................................................... 17
15.3 Accessory Devices...................................................................... 18
15.4 Mounting keypads and zone expanders..................................... 19
15.5 Connecting serial devices ........................................................... 19
Battery Information....................................................................................... 20
16.1 Battery only restart...................................................................... 20
16.2 Replacement period.................................................................... 20
16.3 Discharge/recharge..................................................................... 20
16.4 Battery supervision ..................................................................... 20
16.5 Battery cutoff............................................................................... 20
16.6 XR2400F power requirements.................................................... 20
Bell Output..................................................................................................... 22
17.1 Terminals 5 and 6........................................................................ 22
Keypad and Zone Expander Bus................................................................. 22

18.1 Description .................................................................................. 22
18.2 Terminal 7 - RED......................................................................... 22
18.3 Terminal 8 - YELLOW.................................................................. 22
18.4 Terminal 9 - GREEN.................................................................... 22
18.5 Terminal 10 - BLACK................................................................... 22
Smoke Detector Output................................................................................ 22
19.1 Terminals 11 and 12.................................................................... 22
19.2 Current rating .............................................................................. 22
Powered Zones for 2-Wire Smoke Detectors............................................. 23
20.1 Terminals 25-26 and 27-28 ......................................................... 23
Protection Zones........................................................................................... 24
21.1 Description .................................................................................. 24
21.2 Operational parameters .............................................................. 24
21.3 Zone response time .................................................................... 24
21.4 Keyswitch arming zone ............................................................... 24
Dry Contact Relay Outputs .......................................................................... 25
22.1 Description .................................................................................. 25
22.2 Contact rating.............................................................................. 25
22.3 Output Harness wiring ................................................................ 25
12 VDC Voltage Outputs 3 to 10................................................................... 25
23.1 Description .................................................................................. 25
23.2 Output Harness wiring ................................................................ 25
Reset Jumper J16 ......................................................................................... 26
24.1 Description .................................................................................. 26
24.2 J4 tamper connector ................................................................... 26
UNIVERSAL UL BURGLARY SPECIFICATIONS ......................................... 27
25.1 Introduction ................................................................................. 27
25.2 Wiring .......................................................................................... 27
25.3 Control outside of protected area ............................................... 27
25.4 Police station phone numbers..................................................... 27
25.5 Bypass reports ............................................................................ 27
25.6 System maintenance .................................................................. 27
25.7 Partitions ..................................................................................... 27
25.8 UL Listed Receivers .................................................................... 27
UL 1023 SPECIFICATIONS ........................................................................... 27
26.1 Bell cutoff .................................................................................... 27
26.2 Entry delay .................................................................................. 27
26.3 Exit delay..................................................................................... 27
26.4 Weekly test.................................................................................. 27
UL 1610 AND 1076 SPECIFICATIONS ......................................................... 28
27.1 Multiplex network capacity .......................................................... 28
27.2 Opening/Closing reports ............................................................. 28

27.3 Closing wait ................................................................................. 28
27.4 Proprietary dialer......................................................................... 28
27.5 AA Network Communication ....................................................... 28
UL 1635 SPECIFICATIONS ........................................................................... 29
28.1 System trouble display ................................................................ 29
28.2 Digital Dialer telephone number ................................................. 29
28.3 Entry delay .................................................................................. 29
28.4 Exit delay..................................................................................... 29
28.5 Test time ...................................................................................... 29
28.6 Closing wait ................................................................................. 29
UL 365 AND 609 SPECIFICATIONS ............................................................. 29
29.1 System trouble display ................................................................ 29
29.2 Grade A bell ................................................................................ 29
29.3 Bell cutoff .................................................................................... 29
29.4 Automatic bell test....................................................................... 29
29.5 Line security for Police Connect ................................................. 29
29.6 High Line Security....................................................................... 29
UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS ..................... 30
30.1 Introduction ................................................................................. 30
30.2 Wiring .......................................................................................... 30
30.3 Transformer ................................................................................. 30
30.4 End of Line resistor ..................................................................... 30
30.5 System trouble display ................................................................ 30
30.6 Fire display .................................................................................. 30
30.7 Police station phone number ...................................................... 30
30.8 System maintenance .................................................................. 30
30.9 Audible alarm .............................................................................. 30
30.10 Fire zone programming............................................................... 30
30.11 Style D zones .............................................................................. 30
30.12 Video Option ............................................................................... 30
30.13 UL Listed Receivers .................................................................... 30
UL 985 NFPA 72 (Chapter 2) SPECIFICATIONS ........................................ 31
31.1 Bell output definition.................................................................... 31
UL 864 NFPA 72 (Chapter 9) SPECIFICATIONS ........................................ 31
32.1 Zone restoral reports................................................................... 31
32.2 Power fail delay ........................................................................... 31
32.3 Sprinkler supervisory .................................................................. 31
32.4 DACT systems............................................................................. 31
32.5 Type 2 and Type 3 Central Station Service................................. 31
32.6 Type 1 Central Station Service ................................................... 31
32.7 Local Protective Signaling Systems............................................ 31
32.8 Proprietary Protective Signaling Systems .................................. 32
32.9 Remote Station Protective Signaling Systems ........................... 32

CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS .......................... 32
33.1 Bell output definition.................................................................... 32
System Wiring Diagrams.............................................................................. 33
34.1 Multiple indicating circuit modules .............................................. 33
34.2 Multiple indicating circuit modules for zoned annunciation ........ 34
34.3 Dual Style D Zone Module installation........................................ 35
34.4 Remote Station reversing relay connection ................................ 36
34.5 Supervised remote relay............................................................. 37
34.6 Cellular backup installation for Derived Channel burglary.......... 38
34.7 LX-Bus™ Module Connection .................................................... 39
34.8 Second LX-Bus with Auxiliary Power Supply.............................. 40
OPERATING INSTRUCTIONS ....................................................................... 41

1
Introduction
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
Introduction
1.1 Overview
The DMP XR2400F Addressable Fire Alarm Control Panel (FACP) is an expandable 24 VDC Fire Alarm Control
with built-in DACT and LCD Fire Command Center keyboard with membrane keyswitch. A complete system
can provide a total of 494 programmable inputs and outputs for commercial and industrial fire alarm service.
The 24 VDC 4 Amp notification appliance power is distributed between two class B style W NAC outputs.
Additional NAC outputs can be added with conventional supervision modules or addressable power supply/
boosters. Addressable smoke detectors and input modules round out the XR2400F to deliver a truly flexible and
expansive fire detection and notification system. The Fire Alarm Control Panel is shipped pre-wired in a red
metal enclosure housing the necessary components to monitor and control fire alarm notification appliances.
1.2 System Components
The XR2400F FACP consists of the following components:
• One Model XR2400F Command Processor panel • One Model 893A Dual Phone Line module
• Two Model 866 Class B Style W NAC modules • One Model 630F PCB and membrane switch
• One Model 504-24 VDC Power Supply • One 28 VAC transformer, TF-0030
• One 100 VAC transformer, TF-0015 • One Model 462N LX-Bus Expansion Card
• Two Model 305 Relays
1.3 Power Specifications
Command Processor:
Transformer Input of 16.5 VAC 100 VA
Standby battery of 12 VDC 30.8Ah (100VA charges up to four 7.7Ah batteries)
Auxiliary power of 12 VDC at 1 Amp
NAC Output of 12 VDC at 1.5 Amp
All circuits are inherent Power Limited except red battery wires.
NAC Output:
24 VDC 4 Amps shared between NACs 1 and 2
1.4 Before you begin
Before installing the XR2400F, we recommend you read through the entire contents of this guide. Familiarize
yourself with the features of the panel and the key points to remember during the installation. Be sure to read
and understand all of the caution statements printed in bold italics.
1.5 About this guide
The information in this guide is organized into five sections: Table of Contents, Introduction, Installation,
Compliance, and System Wiring Diagrams.
• The Table of Contents at the front lists the headings and subheadings used throughout each section of
the guide.
• The Introduction section gives you an overview of the XR2400F and this document.
• The Installation section begins with mounting instructions for the enclosure. Wiring diagrams for each
component also appear in this section.
• The Compliance section lists all UL listings the XR2400F currently follows.
• The System Wiring Diagrams provide illustrations of typical XR2400F systems.
Caution notes
Throughout this guide you will see caution notes containing information you need to know when installing the
XR2400F panel. These cautions are written in bold and italics. Failing to follow the caution note may cause
damage to the equipment or improper operation of one or more components in the system.
1.6 How to use this guide
To locate information about the installation of the XR2400F, go to the Table of Contents at the front of this
guide. Find the subject heading that best describes the information you need and turn to the section number
shown to the right of the heading. If you cannot find the information you need under that heading, scan through
a few of the headings and read the text under those that sound similar.

2
Installation
XR2400F Installation Guide
Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803
Mounting
2.1 Mounting the enclosure
The XR2400F must be mounted in a secure, dry location to protect the unit from damage due to tampering and
the elements. The enclosure can be either flush mounted or surface mounted and includes a hinged door with
lock. A hole has been cut in the enclosure door to allow access to the Fire Command Center without opening
the door. Below are the mounting hole locations for the panel's enclosure.
Figure 1: Enclosure Mounting Diagram
2.2 Surface mounting
The center hole of the enclosure should be attached to a stud in the wall. Due to the weight of the enclosure,
especially the batteries, it is extremely important to mount the enclosure on the stud. Attach the two holes
beside the center hole to sheetrock to secure enclosure. When mounting the enclosure, be sure to leave room
for the panel door to swing open. The door's lock should be in an easily accessible place.
2.3 Flush mounting
The enclosure can also be flush mounted (recessed in the wall). 1" screws should be used to secure the
enclosure between two studs using the two sets of holes on the sides of the enclosure.
2.4 The Fire Command Center LCD Keyboard
A Fire Command Center has been factory installed in the XR2400F panel. The keyboard is mounted on a metal
backplate. A hole has been cut into the enclosure door to allow users to control the XR2400F without opening
the enclosure door. Also, a keyswitch has been installed and pre-wired to the left of the keyboard. The user
can turn the keyswitch to enable the four functions keys without opening the enclosure door.
3/4" x 1/2"
Knockouts
Holes for 1" screws when
Flush mounting the enclosure
Additional mounting holes
for Surface mounting
Mounting holes for
Surface mounting.
Hole for Flush mounting
Hole for Flush mounting

3
Installation
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
2.5 Wiring diagram
The XR2400F system below shows the layout of the components. The wires shown in this guide have been
factory installed and connected. The dashed lines represent wires that run underneath a component. Detailed
wiring diagrams for each supplied component appear in following sections of this guide.
Figure 2: XR2400F System
866
Module
#2
866
Module
#1
28 VAC Transformer
WHITE
BLACK
BLACK
GREEN
WHITE
16.5 VAC
Transformer
J16
Reset
Output Header J2
AC
123 4 5 6 7
8
10 11 12 13 14 15 16 17 18 19 920 21 22 23 24 25 26 27 28
AC +B -B BELL GND SMK GNDRED YEL GRN BLK Z1 Z2GND GND GND GND Z3 Z4 Z5 Z6 Z7 Z8 Z9 + Z9 - Z10 + Z10 -
J3
J10
AC AC + BAT -
NC C NO NC C NO
AC TRBL BATT TRBL
+ DC DC -
Black wire to negative
battery terminal
Red wire to positive
battery terminal
To 24 VDC
battery
504-24 Power Supply
893A
Install batteries as shown above.
XR2400F Command
Processor Panel
To Telco
SS
To Notification
Appliances
To Notification
Appliances
462 N LX-Bus Zone Expansion
Card
+-
+-+-+-
Two 12 VDC batteries connected
in parallel with a Model 318 Dual
Battery Harness. See
Secondary Power Supply
section.
12 VDC
battery 12 VDC
battery
Two 12 VDC batteries connected
with a Series Connecting Strap.
Total of 24 VDC for 504-24
Power Supply. See Secondary
Power Supply section.
12 VDC
battery
12 VDC
battery
From 504-24 Power
Supply to 24 VDC. From XR2400F
panel to 12 VDC.
Keyswitch
Red
Black
Black
Red
Bonding
Strap to
Door
S
S
S
S
S
S
Power limited/class 2-wire routing
through conduit knockouts
Power limited/class 2-wire
routing through conduit
knockouts
Power limited/class
2-wire routing
through conduit
knockouts

4
Introduction
XR2400F Installation Guide
Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803
AC Connection
3.1 Transformers and AC Power Connection
The AC connection should be completed by a licensed electrician.
Never share the Fire Alarm Control Panel circuit with any other equipment.
The XR2400F comes supplied with two transformers: the 16.5 VAC 100 VA transformer and the 28 VAC 175 VA
transformer. The 28 VAC and 16.5 VAC transformers' white leads and black leads must be connected together
respectively. These wires must be connected to an unswitched 120 VAC 60 Hz power source with at least 1.85
Amps of available current.
Black wire - attach the black 120 VAC wire to the black wire of the transformers.
White wire - attach the white 120 VAC wire to the white wire of the transformers.
Green wire - attach the green wire lead to the green wire attached to the enclosure.
Figure 3: Transformers and AC Power Connection
Always ground the panel before applying power to any devices!
Use 18 AWG or larger for all power connections. The XR2400F must be properly grounded before connecting
any devices or applying power to the panel. Proper grounding protects against Electrostatic Discharge (ESD)
that can damage system components.
3.2 28 VAC Transformer
The 28 VAC Transformer supplies power to the AC terminals of the 504-24 Power Supply which is factory pre-
wired to the two 866 NAC modules. The 28 VAC is located in the upper right hand corner of the enclosure
surrounded by a metal divider. See Figure 3: Transformers and AC Power Connection. Also refer to 504-24
Power Supply Connection.
28 VAC Transformer
WHITE
BLACK
BLACK
GREEN
WHITE
GREEN
16.5 VAC
Transformer
Terminal 1 Terminal 2
Factory assembled
and connected
To XR2400F Panel

5
Installation
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
3.3 16.5 VAC Transformer
The 16.5 VAC 100 VA transformer supplies power to the XR2400F panel and is factory pre-wired. See Figure 3:
Transformers and AC Power Connection. Also refer to Figure 11: XR2400F Panel Wiring Diagram.
3.4 Earth ground from the XR2400F panel
Terminal 4 of the XR2400F panel must be connected to earth ground using 14 gauge or larger wire to provide
proper transient suppression. DMP recommends connecting to a cold water pipe or ground rod only. Do not
connect to an electrical ground or conduit, sprinkler or gas pipes, or to a telephone company ground.
Secondary Power Supply
4.1 Description
The XR2400F system includes pre-wired cables for connecting a 24 VDC battery to the 504-24 power supply
and a 12 VDC battery to the XR2400F panel. For 24 VDC battery operation to the 504-24, connect two 12 VDC
sealed lead-acid batteries in series using the included series connecting strap (See Figure 4). Observe polarity
when connecting all batteries.
Use sealed lead-acid batteries only. Use the DMP Model 367, 12 VDC 7.0Ah sealed lead-acid rechargeable
battery. Batteries supplied by DMP or manufactured by Eagle Picher or Yuasa have been tested to ensure
proper charging with DMP products.
Gel cell batteries cannot be used with the XR2400F panel.
4.2 Battery Connection to XR2400F Command Processor panel
For 12 VDC battery operation to the XR2400F, connect the black battery lead to the negative terminal of the
battery. The black battery wire is connected to terminal 4 of the XR2400F panel.
Connect the red battery lead to the positive terminal of the battery. The red battery wire is connected to terminal
3 of the XR2400F panel. See Figure 11: XR2400F Panel Wiring Diagram and Figure 2: XR2400F System.
You can add a second battery in parallel using the DMP Model 318 Dual Battery Harness. When wiring two
batteries with the Model 318 Dual Battery Harness, plug the red male end of the Dual Battery Harness into the
red female battery lead from the panel. Plug the black male end of the Dual Battery Harness into the black
female battery lead from the panel. Attach both female leads from the Dual Wiring Harness to the two batteries
as described above. See Table 3: Battery Calculations.
4.3 Battery Connection to the 504-24 Power Supply
The 504-24 is powered by 24 VDC. After connecting two 12 VDC batteries together using the series connecting
strap (or after installing one 24 VDC battery) connect the black battery wire to the negative terminal of the 24
VDC battery. The black battery wire is connected to the negative AC terminal of the 504-24.
Connect the red battery wire to the positive terminal of the 24 VDC battery. The red battery wire is connected to
the positive AC terminal of the 504-24.
See Figure 9: 504-24 Wiring Diagram and Figure 2: XR2400F system. Also see Battery Information section.
12
VDC
Battery
12
VDC
Battery
+
-
+
-
RED
BLACK
Series
Connecting
Strap
Figure 4: 24 VDC wiring

6
Installation
XR2400F Installation Guide
Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803
Two 866 NAC Modules
5.1 Description
Each 866 provides one style W indicating circuit for supervising UL polarized notification appliances, such as
bells, strobes, and horns. See Table 1: Notification Appliances for a list of approved notification appliances.
5.2 Connection
Each 866 module is pre-installed on the right side of the enclosure wall using the standard three-hole
configuration. The modules are factory pre-wired to each other, the 504-24, and the XR2400F panel. Refer to
figure below and to Figure 2: XR2400F System for wiring connections.
You can connect 24 VDC Notification Appliances to terminals 5 and 6 of each module. Each module provides a
zone of notification and can be activated separately.
Figure 5: 866 Wiring Diagram
5.3 Bell Silence/Bell Trouble
A bell silence switch on the 866 module is provided to prevent sounding of the indicating devices when testing
the system. When the Silence position is selected, a fifteen second delay occurs before the 866 bell trouble
contacts (terminals 7 and 8) open. Select the Normal position after testing to return the 866 module to normal
operation.
10K
DMP
M
To XR2400F 0utput #1 (J2 pin #2)
Pre-installed 1K EOLR
To XR2400F terminal 13 ( Zone 1)
To XR2400F terminal 7
To 504-24 DC (-)
To XR2400F output #2 (J2 pin #5)
To 504-24 DC (+)
To XR2400F terminal 15 ( Zone 2)
To 504-24 BATT TRBL C (Common)
866
Module #1
866
Module #2
Normal/Silence Switch
Normal/Silence Switch
1 AUX PWR
2 GND
3 Alarm In
4 Bell PW R In
5 Bell Out +
6 Bell Out -
7 Bell Trouble
8 Bell Trouble
1 AUX PWR
2 GND
3 Alarm In
4 BellPWR In
5 Bell Out +
6 Bell Out -
7 Bell Trouble
8 Bell Trouble
Pre-installed 1K EOLR
10K
DMP
M

7
Installation
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
5.4 Notification Appliances
The following table indicates the approved notification appliances that can be used with the XR2400F system.
Table 1: Notification Appliances
PMD ledoM noitpircseD
WCM-329ebortS/nroHalednac-itluM
W51-329dc51,tnuoMhsulF,ebortS/nroH
W03-329dc03,tnuoMhsulF,ebortS/nroH
W57-329dc57,tnuoMhsulF,ebortS/nroH
W011-329dc011,tnuoMhsulF,ebortS/nroH
W5751-329dc57/51,tnuoMhsulF,ebortS/nroH
WCM-429ebortSelbiduAalednac-itluM
C51-429dc51,tnuoMgnilieC,ebortSelbiduA
W51-429dc51,tnuoMllaW,ebortSelbiduA
C03-429dc03,tnuoMgnilieC,ebortSelbiduA
W03-429dc03,tnuoMllaW,ebortSelbiduA
C57-429dc57,tnuoMgnilieC,ebortSelbiduA
W57-429dc57,tnuoMllaW,ebortSelbiduA
C001-429dc001,tnuoMgnilieC,ebortSelbiduA
W011-429dc011,tnuoMllaW,ebortSelbiduA
W5751-429dc57/51,tnuoMllaW,ebortSelbiduA
PMD ledoM noitpircseD
208ecnailppAelbiduAenot-itluM
308ecnailppAnroH
138eludoMcnyStiucriCelgniS
238eludoMcnyStiucriClauD
109nroHiniMcirtceleozeiP
409ecnailppAnroH
PW409foorp-rehtaeW,ecnailppAnroH
6-609"6lleBrotoM
01-609"01lleBrotoM
WCM-129ebortSetomeRalednac-itluM
C51-129dc51,tnuoMgnilieC,ebortSetomeR
W51-129dc51,tnuoMllaW,ebortSetomeR
C03-129dc03,tnuoMgnilieC,ebortSetomeR
W03-129dc03,tnuoMllaW,ebortSetomeR
C57-129dc57,tnuoMgnilieC,ebortSetomeR
W57-129dc57,tnuoMllaW,ebortSetomeR
C001-129dc001,tnuoMgnilieC,ebortSetomeR
W011-129dc011,tnuoMllaW,ebortSetomeR
W5751-129dc57/51,tnuoMllaW,ebortSetomeR
WCM-229ebortSetomeRalednac-itluM
W51-229dc51,etalPtiforteR,ebortSetomeR
W03-229dc03,etalPtiforteR,ebortSetomeR
W57-229dc57,etalPtiforteR,ebortSetomeR
W011-229dc011,etalPtiforteR,ebortSetomeR
W5751-229dc57/51,etalPtiforteR,ebortSetomeR

8
Installation
XR2400F Installation Guide
Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803
462N LX-Bus™ Expansion Card
6.1 Description
The 462N LX-Bus™ Expansion Card provides an additional 100 zones to the XR2400F.
6.2 LX-Bus™ Expansion Capability
The 462N card provides a 4-wire LX-Bus™ that allows you to connect up to 100 Model 521LX or 521LXT
Addressable Smoke Detectors. Also the LX-Bus™ could connect up to 25 Model 714 and 715 Zone Expanders
or 716 Output Expanders, up to six Model 714-16 or 715-6 Zone Expanders, and up to 100 Model 711 and 711E
Zone Expanders. Power for the devices is provided through the Black and Red wires of the expansion harness.
6.3 Installing the 462N module
1. Remove AC and battery power from the XR2400F panel before installing the 462N card.
2. Align the 50 pin connector of the 462N with the J6 connector on the XR2400F panel.
3. Press the 462N onto the J6 connector while applying even pressure to both sides.
Figure 6: 462N Wiring Diagram
B
{
J6 Expansion
Connector
Zone Expander Harness
Zone Expansion Connector
To LX-Bus Modules
BlackGreen
YellowRed
Bk. - Aux. Common
Gr. - Serial Data Out
Yl. - Serial Data In
XR2400F Command Processor Panel 462N LX-Bus
Zone Expansion
Card
Rd. - Aux. Positive

9
Installation
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
Telephone RJ Connector
7.1 Description
Connect the XR2400F system to two lines of the public telephone network by installing two DMP 356 RJ Cables
between the RJ31X or RJ38X phone jacks and the 893's J4 connector (for main line) and J5 (for backup line).
Set the 3-pin headers labeled J11 and J12 on the XR2400F to DD for digital dialer, Contact ID, or Modem IIe
operation. See 893A Dual Phone Line Module.
Figure 7: Phone Jack Wiring
7.2 FCC registration
The Model XR200/XR2400F complies with FCC part 68 and is registered with the FCC. Registration number:
CCKUSA-18660-AL-R / Ringer Equivalence: 1.1B
7.3 Notification
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be
immediately unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal
equipment may not be used on party lines or in connection with coin telephones. Notification must be given to
the telephone company of:
a. The particular line(s) the service is connected to
b. The FCC registration number
c. The ringer equivalence
d. The make, model, and serial number of the device
7.4 Ground start
Ground start phones cannot be used on commercial or residential fire applications.
893A Dual Phone Line Module
8.1 Description
The 893A is a dual telephone line supervision module that allows the panel to indicate a phone line failure to the
premises and the central monitoring station. After the 893A senses a failure on the main line, it switches to the
backup, or secondary, phone line. The 893A is installed on the left side of the XR2400F enclosure.
8.2 Connection
The 893A connects the panel to the public telephone network by installing a DMP 356 RJ Cable between the
XR2400F panel's J3 connector and the 893's J3 connector labeled PANEL. The two communication jumpers
must be set to either DD or MPX.
1
2
3
45
6
7
8
Tip 1
Tip
Ring
Ring 1
To TELCO Line
To Premises Phone
Place a jumper across
terminals 2 and 7 to provide
phone jack supervision. Loss
of the jumper shows as a
phone trouble on the
Security Command keypad
display.
RJ31X or RJ38X
phone jack

10
Installation
XR2400F Installation Guide
Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803
Figure 8: 893A Wiring Diagram
8.3 Jumper Settings
There are two sets of jumpers on the 893A module. When setting the module for either DD (digital dialer) or
MPX (multiplex), both jumpers must be set.
8.4 Digital Dialer/Multiplex
You can configure the 893A to provide two lines of digital dialer or one line of multiplex with digital dialer backup.
For multiplex operation both jumpers (J1 and J2) must be set to MPX. Also, jumpers J11 and J12 on the panel
must be set to MPX. See XR2400F Command Processor Panel Connection. The XR2400F is preset at the
factory for Digital Dialer. The Main modular jack (J4) is used for the primary dialer or multiplex line. The Backup
modular jack (J5) is used for the secondary digital dialer line.
8.5 Phone Line Monitor
The 893A uses a phone line monitor for the main and backup phone lines. When sending a report, the 893A
verifies the main phone line is working before sending. If the line is bad, the module tests the backup phone line.
The 893A sends the report on the first working phone line.
The phone line monitor has a two minute trouble delay and a one minute restore delay. Phone line trouble is
displayed in the Fire Command Center LCD Status List as a System Trouble. The Fire Command Center LCD is
factory programmed to display system troubles in the Status List.
8.6 Processor Fail Buzzer
The 893A module also monitors the panel's CPU and sounds a trouble buzzer whenever either the panel's
processor is reset using J16 or the processor stops functioning.
504-24 Power Supply
9.1 Description
The 504-24 is a power limited, switching power supply that meets UL, CSFM, NFPA, and FCC compliance
standards. Model 504-24 is rated for 24 VDC @ 4 Amps maximum and supplies power to the 866 NAC
modules.
9.2 LED's
The 504-24 has two status LED's that show the current state of power. The green LED indicates low AC input.
The red LED indicates low standby battery power after AC has failed.
P10
Panel
Main Backup
J4 J5
J3
J2
J1
DD
MPX
DD
MPX
Communication Jumpers (Both
Jumpers must be set)
To Primary
Phone Line To Secondary
Phone Line
Factory pre-wired
To Panel phone
jack connector J3
Processor
Stopped Buzzer
Factory Pre-wired to
Panel connector
J10

11
Installation
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
Power supply operating current 200 mA
Other standby current + _______ mA
1. Total standby current = _______ mA
No. of standby hours required X _______ hr
2. Total standby (mA.hr required) = _______ mA.hr
3. Total alarm current = _______ mA
Total alarm current X .25 = _______ mA.hr
(.25 = 5 minute alarm)
Total standby (required) + _______ mA.hr
Total = _______ mA.hr
X .001
4. Total required Amp.hrs = _______
9.3 504-24 Condition Chart
Table 2: 504-24 Conditions
9.4 504-24 UL Listings
For UL 603 Power Supplies for Burglary Alarm Systems and UL294 Power Supplies for Access Control System
applications: Voltage Range of 22.9 to 25.5 VDC.
For UL1481 Power Supplies for Fire Protective Signaling the following maximum battery standby Ampere hours
apply for 24 hours of battery backup: Battery Standby Maximum: 49.2 AH
Output Voltage: 24 VDC
Output Current: 1.5A standby, 4 Amp alarm
9.5 24 VDC NAC Standby Battery Calculations
The following calculation defines the total number of standby battery Amp.hours required to support operation of
the NACs and any other devices attached to the 504-24 power supply. From this calculation, assemble the
appropriate number of batteries that will just exceed the calculated total Amp/hour requirement. The 866 NACs
receive power for internal operation from the XR2400F panel and do not enter in this calculation themselves.
1. Add all standby current values including the power supply operating current.
2. Multiply the total standby current by the number of standby hours needed.
3. Add all alarm current values from the notification appliances attached to the 866 NACs and multiply by 0.25.
4. Add the total alarm mA. hour with the total standby mA. hour and then multiply this number by .001.
Table 3: Battery Calculations
9.6 Connection
The 24 VDC power supply is completely pre-wired. Refer to the following 504-24 wiring diagram for specific wire
connections.
LED Status Condition
AC LED (GRN) ON AC Good
AC LED (GRN) OFF AC Bad
DC LED (RED) ON AC Good, Battery Good
DC LED (RED) OFF AC Good, Battery Bad
Condition 504-24
AC Trouble Approx. 102 VAC
Battery Trouble Below 23.6 VDC
Battery Restoral Above 25.0 VDC
Battery Cutoff Below 20.4 VDC

12
Installation
XR2400F Installation Guide
Digital Monitoring Products www.dmpnet.com 2500 N. Partnership Boulevard Springfield, MO 65803
Interconnect Wiring Harness
10.1 Interconnect Harness
This chart explains the colors of the wires on the Interconnect Wiring Harnesses. It also explains what each
wire connects.
Figure 9: 504-24 Wiring Diagram
Table 4: Interconnect Wiring Harness
AC TRBL BATT TRBL
To 866 Module
#2 terminal 4
(Bell PWR In)
Black wire to negative
battery terminal
Red wire to positive
battery terminal
To 24 VDC
battery
Both wires
To 28 VAC
Transformer
To 866 Module
#2 terminal 8
(BELL TRBL)
To XR200 Panel
terminal 16
(Zone 3)
To XR200 Panel
terminal 10 (BLK)
AC DC
Green
LED Red LED
White/Red
Black
Black
Green
Black
Yellow
Blue
To 866 Module #2
terminal 2 (GND)
Model 504-24 Power Supply
+ DC DC-
AC AC + BAT -
To XR200 Panel
terminal 18
(Zone 4)
NC C NO NC C NO
Color From To
Red Panel terminal 7 (DC Power) 866 Module #2 terminal 1 (AUX PWR)
Black Panel terminal 10 (Common) 504-24 DC-
Brown Panel terminal 13 (Zone 1) 866 Module #1 terminal 7 (Bell Trouble)
Violet Panel terminal 15 (Zone 2) 866 Module #2 terminal 7 (Bell Trouble)
Green Panel terminal 16 (Zone 3) 504-24 Battery Trouble terminal N/O
White Panel terminal 18 (Zone 4) 504-24 AC Trouble terminal N/C
Blue Panel J2 pin 2 (Common) 866 Module #1 terminal 3 (Alarm In)
Orange Panel J2 pin 3 (Output 1 N/O) Panel terminal 5 (Bell Output)
Yellow Panel J2 pin 5 (Common) 866 Module #2 terminal 3 (Alarm In)
Orange Panel J2 pin 6 (Output 2 N/O) Panel terminal 5 (Bell Output)
White/Red 504-24 DC+ 866 Module #2 terminal 4 (Bell PWR In)
Black 504-24 DC- 866 Module #2 terminal 2 (GND)
Red 866 Module #2 terminal 1 (AUX PWR) 866 Module #1 terminal 1 (AUX PWR)
Black 866 Module #2 terminal 2 (GND) 866 Module #1 terminal 2 (GND)
Black 866 Module #2 terminal 2 (GND) 866 Module #1 terminal 8 (Bell Trouble)
White/Red 866 Module #2 terminal 4 (Bell PWR In) 866 module #1 terminal 4 (Bell PWR In)
Black 866 Module #2 terminal 8 (Bell Trouble) 504-24 Battery Trouble terminal Common
Black 866 Module #2 terminal 8 (Bell Trouble) 866 Module #1 terminal 8 (Bell Trouble)

13
Installation
XR2400F Installation
Guide
2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products
Fire Command Center
11.1 Description
The XR2400F provides an LCD display and 20-key keyboard for programming and user operation of the system.
The Fire Command Center is installed on a mounting plate for easy access through the enclosure door. To the
left of the keyboard, a keyswitch has been installed and pre-wired. The user must turn the keyswitch to enable
the four function keys. See the illustration below.
11.2 Connection
The display and keyboard are factory pre-wired to terminals 7, 8, 9, and 10 of the XR2400F panel. For standby
battery calculations, the display draws 100mA of current in normal standby or alarm condition. See Panel
Standby Battery Calculations. The keyswitch has been pre-wired to the membrane keyboard.
11.3 Remote Fire Command Center
Up to seven Model 630F Remote Fire Command Centers may be remotely attached to the XR2400F system.
See 630F Installation Guide, LT-0562, for complete information.
Figure 10: Fire Command Center keyboard and
display