DMP Electronics 1135 User manual

InstallatIon GuIde
1135 Wireless Siren
Description
The Model 1135 Wireless Siren provides 100 decibels of annunciation and comes with
a wall, cover tamper, survey LED, and two batteries. Multiple sirens can be activated
simultaneously by the panel via the Trip with Panel Bell feature.
What is included
The 1135 includes the following:
• One1135WirelessSiren
• Two3.0VLithiumCR123Abatteries
• Hardwarepack
• Serialnumberlabel
• Double-sidedtape
Serial Number
Foryourconvenience,twoadditionalpre-printedserialnumberlabelsareincludedfor
the siren output. Prior to installing the wireless siren, record the serial number or place
thepre-printedserialnumberlabelonthepanelprogrammingsheet.Thisnumberis
required during programming.
Programming the 1135 Siren Output in the Panel
Refertothepanelprogrammingguideasneeded.InOutputInformation,enteranoutputnumber,outputname,eight-digit
serialnumber,supervisiontime,andsettheTripwithPanelBelloptiontoYES.Outputsoperatewitha3secondresponse
time when used with the 1135.
InOutputInformationprogramthewirelessoutputas:
XR100/XR500/XR150/XR350/XR550450-474,480-499
XTL/XT30/XT5031-34,41-44
Trip with Panel Bell Option
Select YES to have the 1135 Wireless Siren follow the panel bell output
includingbellcutofftime.TheON/OFFstateofthesirencannotbechangedvia
the output menu or any other panel function. Default is YES.
Note: When the panel is reset, or programming is complete, the supervision
timeisreset.Ifthepanelhasbeenpowereddownformorethanonehour,
the1135maytakeuptoanadditionalhourtosendasupervisionmessage
unless tripped, tampered, or powered up. This operation extends battery life.
Amissingmessagemaydisplayonthekeypaduntilthesupervisionmessageis
sent.Inaddition,ifthesirenisonwhenthepanelispowereddown,thesiren
automatically turns off after 15 minutes.
Installing the Wireless Siren
Selecting a Location
The1135providesasurveycapabilitytoallowonepersontoconrm
communicationwiththereceiverwhilethecoverisremoved.The1135PCB
RedSurveyLED(SeeFigure2)turnsonbrightlywheneverdataissenttothereceiverthenimmediatelyturnsoffwhen
thereceiveracknowledgementisreceived.Pressingthetamperswitchisaconvenientwaytosenddatatothereceiver
toconrmoperation.Whenthe1135doesnotreceiveanacknowledgementfromthereceiverthesurveyLEDremains
onforabout8secondstoletyouknowcommunicationisnotestablished.CommunicationisalsofaultywhentheLED
ashesbrightlymultipletimesinquicksuccession.Relocatethe1135orreceiveruntiltheLEDimmediatelyturnsoffwhen
tampered indicating the 1135 and receiver are communicating properly. Proper communication between the 1135 and
receiverisveriedwhenforeachpressorreleaseofthetamperswitch,theLEDblinksimmediatelyonandimmediately
off.
Tamper Switches
The1135isequippedwithacasetamperandawalltamper.Atwopositionheaderis
provided to disable the wall tamper. To disable the wall tamper, place the jumper across
thetwopinsoftheheader.Ifwalltamperisrequired,placethejumperoverjustonepin
for storage.
Note:Ifmountingusingthesupplieddouble-sidedtape,thewalltampermustbedisabled.
Mounting the Siren
1.Removethelockingscrewsfromthetopandbottomofthesirenhousing.Liftthe
cover from the bottom to remove.
2.Mountthe1135onaatwallensuringthatthewalltamperswitchmakesproper
contact with the wall. Use the supplied screws in the mounting hole locations as
showninFigure2,orusethesupplieddouble-sidedtape.Mountthesirenawayfrom
metalobjects.Donotinstallthe1135within4feetofthepanelastheRFgainofthe
transmitter may inhibit proper communication.
3.Setthecoverbackintoplaceandreplacethelockingscrews.
Powering the 1135
Note: When setting up a wireless system, it is recommended to program the siren's output number
in the panel and connect the receiver before installing batteries in the 1135.
Figure 1: 1135 Wireless Siren
Figure 2: Survey LED and Mounting Holes
Mounting Holes
Model
1135
RED LED
(SURVEY)
TAMPER
SWITCH
SOUNDER
Mounting Holes
Red
Survey
LED
Locking Screw
Locking Screw
WALL
TAMPR DIS
Tamper
Disable
Figure 3: Wall Tamper
Wall
Tamper

800-641-4282
      
www.dmp.com 2500 North Partnership Boulevard

 
LT-1106 1.05 © 2015 Digital Monitoring Products, Inc.
15055
Battery Power
Observepolaritywheninstallingthebatteries.Useonly3.0VLithiumbatteries,DMPModelCR123,ortheequivalent
batteryfromalocalretailoutlet.ForULinstallations,onlyuse#123batteriesmanufacturedbyEnergizer.
1.Removethelockingscrewfromthesideofthesirenhousing.
2.Liftthecoverfromthebottomtoremove.
3.Ifreplacingthebatteries,removetheoldbatteriesanddisposeofproperly.Alwaysreplacebothbatteriesatthe
same time.
Caution:Properlydisposeofunusedbatteries.Donotrecharge,disassemble,heatabove212°F(100°C),or
incinerate.Thereisariskofre,explosion,andburnswithimproperdisposal.
4.PlacethetwoCR123batteriesintheholdersandpressintoplace.SeeFigure2forbatterylocation.
5.Setthecoverbackintoplaceandreplacethelockingscrew.
Battery Life Expectancy
Batterylifeexpectancyforthe1135is3yearswherethesirenisoperatedforveminutesonceamonth.Refertothe
panelprogrammingguideasneeded.DMPwirelessequipmentusestwo-waycommunicationtoextendbatterylife.
The following situation can extend battery life expectancy:
•Infrequentsirenon/offoperations
•Extendtransmittersupervisiontimeinpanelprogramming
The following situations can reduce battery life expectancy:
•Multiplesirenon/offoperations
•Wheninstalledinextremehotorcoldenvironments
FCC Information
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
Theantennausedforthistransmittermustbeinstalledtoprovideaseparationdistanceofatleast20cm(7.874in.)fromall
persons.Itmustnotbelocatedoroperatedinconjunctionwithanyotherantennaortransmitter.
Changesormodicationsmadebytheuserandnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe
user’s authority to operate the equipment.
Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15ofthe
FCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnot
occurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbe
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorientorrelocatethereceivingantenna.
-Increasetheseparationbetweentheequipmentandreceiver.
-Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Listed Compliance Specications
Commercial Burglary
The wall tamper must be enabled for commercial burglary applications.
Installonlyonnon-conductivesurfaces.
Household Fire
SupervisionTimemustbe3minutesforreapplications.
Compatibility
1100DWirelessReceiver
1100DHWirelessHighPowerReceiver
1100DIWirelessIn-lineReceiver
1100XWirelessReceiver
1100XHWirelessHighPowerReceiver
XTL,XTLN,andXTLN-WiFiPanels
XT30/XT50Panels(usingsoftwareversion106orhigher)
XR100/XR500Panels(usingsoftwareversion207orhigher)
XR150/XR350/XR550Panels
Patents
U.S.PatentNo.7,239,236
Certications
FCCPart15RegistrationIDCCKPC0123
IndustryCanadaRegistrationID5251A-PC0123
ANSI/UL1023HouseholdBurglarAlarmSystemUnits
ANSI/UL1610CentralStationBurglarAlarmUnits
ANSI/UL985HouseholdFireWarningSystem
Specications
Battery
Life Expectancy 3 Years
Type 3.0VLithiumCR123A
See Battery Life Expectancy for full details.
FrequencyRange 903-927MHz
Decibel Level 100 dB at 3 ft.
Dimensions 4.5”Lx4.5”Wx1.25”H
Color White
HousingMaterial FlameretardantABS
Accessories
CR123 3.0VLithiumBattery