Dometic 9100 User manual

Read these instructions carefully. These
instructions MUST stay with this product.
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
9100
POWER CHANNEL AWNING
LED TUBE AWNING
HARDWARE
8956(X)(X)1.4(X)0(#) BASEMENT
8956(X)(X)2.4(X)0(#) STANDARD
8956(X)(X)3.4(X)0(#) REDUCED PITCH
8957(X)(X)1.4(X)0(#) BASEMENT
8957(X)(X)2.4(X)0(#) STANDARD
8957(X)(X)3.4(X)0(#) REDUCED PITCH
FRTA
FABRIC ROLLER TUBE ASSEMBLY
601FFLL.000(#)
91XFFLL.000(#)T
6XXFFLL.000(#)Z
RECORD THIS INFORMATION FOR FUTURE
REFERENCE:
FRTA Model Number
FRTA Serial Number
Hardware Model Number
Hardware Serial Number
Date Purchased
Retailer / Qualied Installer
REVISION E
Form No. 3316039.000 1/18
(French 3316040.000_E)
©2018 Dometic Corporation
LaGrange, IN 46761
INSTALLATION
INSTRUCTIONS

2
TABLE OF CONTENTS
INTRODUCTION....................................................................................................................................................................2
DOCUMENT SYMBOLS ........................................................................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS................................................................................................................................3
A. Recognize Safety Information ...................................................................................................................................3
B. Understand Signal Words..........................................................................................................................................3
C. Supplemental Directives............................................................................................................................................3
D. General Safety Messages .........................................................................................................................................3
GENERAL INFORMATION.....................................................................................................................................................3
A. Included Hardware ....................................................................................................................................................3
B. Optional Components & Kits .....................................................................................................................................3
SPECIFICATIONS..................................................................................................................................................................4
A. Hardware Dimensions (Back Channel) .....................................................................................................................4
B. Door Clearance .........................................................................................................................................................4
C. Measuring Tips ..........................................................................................................................................................4
PREPARE FOR INSTALLATION............................................................................................................................................5
A. Door Roller And Edge Guard (Optional) ....................................................................................................................5
B. Prepare Awning Rail And Insert Fabric......................................................................................................................5
C. Prepare Awning For Installation.................................................................................................................................5
D. Determine Awning Location.......................................................................................................................................7
INSTALL ELECTRICAL KITS .................................................................................................................................................8
A. Install (Fixed / Wired) Awning Switch ........................................................................................................................8
B. Install Track And Light Switches (If Applicable) .........................................................................................................8
C. Install Ignition / Safety Interlock System....................................................................................................................8
D. Install LED Light Switch (If Applicable) ......................................................................................................................8
INSTALL AWNING..................................................................................................................................................................9
A. Insert Awning Fabric Into Awning Rail .......................................................................................................................9
B. Attach Top Mounting Brackets.................................................................................................................................10
C. Attach Back Channels ............................................................................................................................................. 11
D. Electrical Connections To Awning............................................................................................................................12
E. Complete Back Channel Installation........................................................................................................................13
F. Secure Awning Fabric To Awning Rail .....................................................................................................................14
VERIFY INSTALLATION.......................................................................................................................................................14
A. Test Operation .........................................................................................................................................................14
B. Secure Awning For Travel .......................................................................................................................................14
C. Keep Literature ........................................................................................................................................................14
INTRODUCTION
This awning (hereinafter referred to as “awning,” or “product”) is designed and intended for use on RVs with straight sides.
For curved sides, please see the separate Hardware List in the Dealer Service Manual for the appropriate model. This
product can be installed by one person with brief help from additional personnel. Use these instructions to ensure correct
installation and function of product.
Dometic Corporation reserves the right to modify appearances and specications without notice.
DOCUMENT SYMBOLS
Indicates additional information that is NOT related
to physical injury. Indicates step-by-step instructions.

3
This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries.
A. Recognize Safety Information
This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
B. Understand Signal Words
A signal word will identify safety messages and
property damage messages, and will indicate the
degree or level of hazard seriousness.
 indicates a hazardous situation that,
if NOT avoided, could result in death or serious in-
jury.
 indicates a hazardous situation that,
if NOT avoided, could result in minor or moderate
injury.
 is used to address practices NOT
related to physical injury.
C. Supplemental Directives
Read and follow all safety information and
instructions to avoid possible injury or death.
Read and understand these instructions be-
fore installing, using, servicing or performing
maintenance on this product.
Incorrect installation, operation, servicing
or maintaining of this product can lead to
serious injury. Follow all instructions.
The installation MUST comply with all ap-
plicable local and national codes, including
the latest edition of the following standards:
U.S.A.
● ANSI/NFPA70, National Electrical Code
(NEC)
● ANSI/NFPA 1192, Recreational Vehicles
Code
CANADA
●CSA C22.1, Parts l & ll, Canadian Electri-
cal Code
●CSA Z240 RV Series, Recreational
Vehicles
D. General Safety Messages
 Failure to obey the following warn-
ings could result in death or serious injury:
●This product MUST be installed and serviced by
a qualied service technician.
●Do NOT modify this product in any way. Modica-
tion can be extremely hazardous.
●IMPACT OR CRUSH HAZARD. This product
should be installed in a controlled environment
(inside). Do NOT install product during windy
conditions, or when wind is expected. Otherwise,
product could move unpredictably, become un-
stable, and could detach, bend, or collapse.
IMPORTANT SAFETY INSTRUCTIONS
A. Included Hardware
(2) 1/4″ - 20 x 3/4″ Hex Head Screw
(2) 1/4″ Split Lock Washer
(8) #14 - 10 x 1-1/2″ Hex Head Screw
(2) #6 - 20 x 7/16″ Self Drilling Hex Head Washer
Screw
B. Optional Components & Kits
(1) 830304 Door Roller Kit
(1) 830304.003 Door Roller Kits (50 Pack)
(1) 3308334.006U Torsion Crank Assembly
(1) 3312853.025(#) Back Channel Spacer Kit
(1) 3316287.000 Rocker Switch Kit
GENERAL INFORMATION

4
SPECIFICATIONS
A. Hardware Dimensions (Back Channel)
Wiring harness location may be at top or bot-
tom depending on awning model.
FIG. 1
H
L
D
E
F
C
B
A
K
J
G
Bottom
Wiring
Harness
Hole
M
Top Wiring Harness Notch
8956(X)(X)1.4(X)0(#) 8956(X)(X)2.4(X)0(#) 8956(X)(X)3.4(X)0(#)
A62-3/4″ 66-1/4″ 66-1/4″
B62-1/8″ 65-5/8″ 65-5/8″
C60-1/8″ 63-5/8″ 63-5/8″
D60-3/4″ 64-1/4″ 64-1/4″
E61-1/2″ 65″ 65″
F31″ 32-7/8″ 32-7/8″
G35-1/4″ N/A N/A
H3/8″
J1/4″
K5/8″
L3/4″
M1-1/2″
B. Door Clearance
Minimum distances between awning rail and entry
door:
X
8956(X)(X)1.4(X)0(#) 12″
8956(X)(X)2.4(X)0(#) 7″
8956(X)(X)3.4(X)0(#) 6″
When entry door is toward center of awning,
add 2″ to minimum distances.
FIG. 2 Awning Rail
Entry Door
X
C. Measuring Tips
Consider doors, windows, lights, trim, slideout
room, etc. when determining the length and posi-
tion of the awning so as not to obstruct the opera-
tion or block any of these components.

5
PREPARE FOR INSTALLATION
A. Door Roller And Edge Guard (Optional)
 Do NOT allow corner of entry door
to contact awning fabric. Otherwise, premature
wear or tearing of awning fabric could occur.
If there’s potential for a squared corner entry door
to contact awning fabric, a door roller kit (NOT IN-
CLUDED) must be installed.
Rounded corner doors may NOT require a
door roller kit if there is no potential for dam-
age to awning fabric.
See subsection, “B. Optional Components &
Kits” on page (3) to order door roller kits.
1. Place door roller on upper corner of outer entry
door (opposite to hinge), transfer (drill) two pilot
holes, and place and tighten mounting screws.
See (FIG. 3).
FIG. 3
Position Wheel
Directly Over
Edge Of Door
Outer Entry
Door
1/4″ - 3/8″
(Above Door)
2. Clip door edge guard onto upper corner of inner
screen door (opposite to hinge). See (FIG. 4).
FIG. 4
Door Edge
Guard
Inner Screen
Door
B. Prepare Awning Rail And Insert Fabric
 Make sure awning rail is parallel to
RV oor, and is NOT warped or curved before in-
stalling awning fabric. If awning rail is NOT straight,
awning fabric may wrinkle or stretch.
Select desired awning rail end (on RV) into which
awning fabric will be inserted. Flare (widen) that
end of rail with a at-bladed screwdriver, and re-
move (le) sharp edges. See (FIG. 5).
If awning is equipped with LED lights, are
top (of awning rail opening) ONLY.
FIG. 5
Before After
LED Awnings:
Flare Top Only
Typical Awnings:
Flare Top And Bottom
C. Prepare Awning For Installation
The awning hardware requires minor preparation
before installing on RV.
1. Carefully lay fabric roller tube assembly (FRTA)
on a clean, well padded “V” trough (or other well
protected surface) to prevent fabric damage.
2.  IMPACT OR PINCH HAZARD.
Do NOT remove ties (wrapped around each arm
assembly) until top casting is secured to front
channel, awning fabric is attached to awning
rail, and arm assembly is mounted to RV. Arm
assemblies are under tension from gas strut.
Removing these ties could allow arms to extend
quickly and unexpectedly. Failure to obey this
warning could result in death or serious injury.
Insert each top casting into corresponding front
channel. See (FIG. 6).
The RH arm assembly (front channel) is
pre-wired for awning motor.

6
FIG. 9
4. Secure RH front channel to RH top casting us-
ing 1/4″ - 20 x 3/4″ hex head screw and 1/4″ split
lock washer. See (FIG. 6).
5. Repeat step () for LH side. See (FIG. 10).
FIG. 10 LH End Cap
Top Casting
FRTA
Cotter Pin
1/4″ - 20 x 3/4″
Hex Head Screw
Front
Channel
FIG. 6
FRTA
Top Mounting
Bracket
Top Casting
Back
Channel
1/4″ - 20 x 3/4″
Hex Head Screw
Front
Channel
FIG. 7
3.  IMPACT OR CRUSH HAZARD.
DO NOT set Top Casting BEHIND Tongue. Aw-
ning roller assembly is NOT properly restrained
and could become separated. Failure to obey
this warning could result in loss of property, seri-
ous injury or death.
FIG. 8
PREPARE FOR INSTALLATION
Groove in
Top Casting
must slide
over tongue
in Main Arm
YES
NO
Groove
Tongue

7
6.  IMPACT OR PINCH HAZARD.
Do NOT remove cotter pin from torsion rod (at
end cap) until BOTH top castings are secured to
corresponding front channels. Otherwise, rapid
casting spin off will occur. Spring tension will at-
tempt to spin the hardware and/or fabric roller
tube quickly and unexpectedly. Failure to obey
this warning could result in death or serious in-
jury.
Remove cotter pin from left hand torsion rod (LH
end cap). See (FIG. 10).
Removing cotter pin will release factory
preset torsion (spring) tension.
a. Straighten bent end of cotter pin.
b. Rotate fabric roller tube (as if unrolling aw-
ning) by pulling bottom of tube toward you.
This will reduce pressure on cotter pin
for easier removal.
c. While holding fabric roller tube, pull cotter pin
out and discard.
D. Determine Awning Location
1.  IMPACT OR CRUSH HAZARD.
Make sure mounting surface on RV is at, has
solid structural backing where fasteners pene-
trate surface, and will safely and securely sup-
port product. Otherwise, product may become
unstable and could detach, bend or collapse.
Failure to obey this warning could result in death
or serious injury.
Find a solid structure in RV wall for support of
top mounting brackets and back channels (all
mounting points).
2. Make sure arm assemblies do not restrict use
of doors, windows, slideout rooms, etc. See
(FIG. 11).
To install over windows, see subsec-
tion, “B. Optional Components & Kits” on
page (3) to order back channel spacer
kits.
3.  Allow for sufcient clearance be-
tween entry door and fabric or slideout room and
fabric to accomodate awning pitch (slope).
Avoid location that interferes with entry door
swing when awning is completely extended. See
subsection, “B. Door Clearance” on page (4).
FIG. 11
PREPARE FOR INSTALLATION

8
INSTALL ELECTRICAL KITS
3. Route wiring (inside RV) to general location
where connections to awning left hand hardware
will be made.
Allow enough wiring length to pass through
outside RV wall (hole will be drilled later)
for connection to awning.
Wiring hole location will be either at top or
bottom of LH back channel depending on
awning model. See (FIG. 1).
4. Make appropriate wiring connections inside RV.
Wiring connections to awning (through
outside RV wall) will be made later.
See instructions included with your Do-
metic Corporation switch kit for additional
wiring instructions.
C. Install Ignition / Safety Interlock System
 IMPACT OR CRUSH HAZARD. Do
NOT install product without also installing an igni-
tion/safety interlock system. Otherwise, accidental
operation during transit could occur. Failure to obey
this warning could result in death or serious injury.
Ignition / safety interlock system is only ap-
plicable to motorhomes.
1.  Install a (3 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc igni-
tion control ( PINK wire) to ignition interlock. Oth-
erwise, damage to unit could occur.
2. Make appropriate wiring connections.
The ignition interlock MUST break the cir-
cuit (cut power) to awning when ignition
is ON.
See instructions included with your Do-
metic Corporation ignition interlock kit
(available separately) for additional wiring
instructions.
D. Install LED Light Switch (If Applicable)
An LED light switch (installer supplied) is required
for awning models equipped with an LED light strip
either at the wall or in the roller tube.
Skip this subsection if awning is NOT
equipped with an LED light strip.
1.  Do NOT expose switch to weath-
er, extreme temperatures, or long hours in direct
sunlight.
Find a suitable location for LED switch installa-
tion.
2.  Install a (3 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc power
supply ( RED wire) to switch. Otherwise, damage
to unit could occur.
 ELECTRICAL SHOCK HAZARD.
Disconnect 120 Vac power from RV. Failure to obey
this warning could result in death or serious injury.
 Disconnect the positive (+) 12 Vdc
terminal from supply battery. Otherwise, damage to
unit could occur.
Disconnect power for ALL procedures under this
section.
A. Install (Fixed / Wired) Awning Switch
Use correct (Dometic Corporation approved)
momentary switch, or electronic control
switch with motor overload protection.
1.  Do NOT expose switch to weath-
er, extreme temperatures, or long hours in direct
sunlight.
Find a suitable location for awning switch instal-
lation.
2.  Install a (15 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc power
supply ( RED wire) to switch. Otherwise, damage
to unit could occur.
3. Route wiring (inside RV) to general location
where connections to awning right hand hard-
ware will be made.
Allow enough wiring length to pass through
outside RV wall (hole will be drilled later)
for connection to awning.
Wiring hole location will be either at top or
bottom of RH back channel depending on
awning model. See (FIG. 1).
4. Make appropriate wiring connections inside RV.
Wiring connections to awning (through
outside RV wall) will be made later.
See instructions included with your Do-
metic Corporation switch kit (available
separately) for additional wiring instruc-
tions.
B. Install Track And Light Switches (If
Applicable)
Use correct (Dometic Corporation approved)
non-momentary switch.
1.  Do NOT expose switch to weath-
er, extreme temperatures, or long hours in direct
sunlight.
Find a suitable location for awning switch instal-
lation.
2.  Install a (15 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc power
supply ( RED wire) to switch. Otherwise, damage
to unit could occur.

9
Alternatively, a (3 A) in-line fuse may be
used between positive (+) 12 Vdc power
supply ( RED wire) and LED switch.
3. Route wiring (inside RV) to general location
where connections to awning hardware will be
made.
Allow enough wiring length to pass through
outside RV wall (hole will be drilled later)
for connection to awning.
Wiring hole location will be either at top or
bottom of RH back channel depending on
awning model. See (FIG. 1).
INSTALL AWNING
INSTALL ELECTRICAL KITS
4. Make appropriate wiring connections inside RV.
Wiring connections to awning (through
outside RV wall) will be made later.
See instructions included with your LED
light switch for additional wiring instruc-
tions.
Unfurl awning fabric 1 revolution before inserting
fabric (with awning roller cover, if equipped) into
awning rail.
Unfurling 1 revolution will allow enough
space between RV wall and awning hard-
ware to guide awning fabric into awning
rail.
2.  LIFTING HAZARD. Use proper
lifting technique and control when lifting product.
Failure to obey this caution could result in injury.
 Keep both arm assemblies paral-
lel to each other to avoid twisting.
With one person grasping each arm assembly,
carefully lift entire awning assembly upright.
Then carry awning to prepared (ared) awning
rail end. See (FIG. 12).
FIG. 12
Awning
Rail
Arm
Assembly
FRTA (Fabric Roller
Tube Assembly)
3. While one person guides awning fabric (with aw-
ning roller cover, if equipped) into awning rail,
carefully move (carry) awning hardware assem-
bly to desired location. See (FIG. 12).
A stepladder may be necessary to reach
awning rail.
At least two other people are required to
hold and control hardware until top mount-
ing brackets and back channels are cor-
rectly installed.
 Failure to obey the following warnings could
result in death or serious injury:
● IMPACT OR CRUSH HAZARD. This product should
be installed in a controlled environment (inside). Do
NOT install product during windy conditions, or when
wind is expected. Otherwise, product could move
unpredictably, become unstable, and could detach,
bend, or collapse.
●FIRE OR ELECTRICAL SHOCK HAZARD. Make sure
there are no obstacles (wires, pipes, etc.) inside the
RV’s roof, oor or walls. Shut OFF gas supply, discon-
nect 120 Vac power from RV, and disconnect positive
(+) 12 Vdc terminal from supply battery BEFORE drill-
ing or cutting into RV. Failure to obey these warnings
could result in death or serious injury.
 Failure to obey the following notices could
damage product or property:
●ALWAYS use sealant on (clean) parts and surfaces
where fasteners enter the RV’s walls, roof or oor.
Otherwise, water leakage could occur.
● Install back channels on a at surface, level, and keep
parallel with each other to ensure correct function and
appearance.
A. Insert Awning Fabric Into Awning Rail
 IMPACT OR CRUSH HAZARD.
Do NOT remove LED rail from awning fabric (if
equipped). Otherwise, awning fabric could sepa-
rate from awning rail (on RV) and cause awning to
extend quickly or detach, bend, or collapse. Failure
to obey this warning could result in death or serious
injury.
If LED light strip is NOT desired, standard
fabric MUST be used. Otherwise, you may
remove LED light strip from LED rail, and
leave empty LED rail on fabric rope.
1.  Do NOT unfurl more than 1 revo-
lution of fabric, as this could cause issues with
the awning closing and opening correctly.

10
B. Attach Top Mounting Brackets
1. When awning is in predetermined location,
place top mounting brackets (with arm assem-
bly) directly under and parallel to awning rail.
See (FIG. 1) & (FIG. 13).
To determine correct awning location, see
subsection, “D. Determine Awning Loca-
tion” on page (7).
The motorized arm assembly is ALWAYS
installed at the RH side of awning.
Some awning rails have a wide drip chan-
nel to catch water as it runs off RV roof. If
awning rail is too wide, it may be neces-
sary to lower the position of top mounting
brackets to avoid interference with FRTA.
FIG. 13 Awning Rail
Top Mounting Brackets
FRTA
Arm Assemblies
2. While holding arm assemblies securely in place,
mark top mounting hole locations (LH and RH
top mounting bracket slots). See (FIG. 13).
3. Wiring hole for motorized arm assembly. See
(FIG. 1).
The motorized arm assembly is ALWAYS
installed at the RH side of awning.
Wiring harness location is determined by
awning model. The back channel will ei-
ther have a notch at top, or a hole near
bottom for wiring to pass through RV wall.
a. If wiring will pass through RV wall at BOT-
TOM of back channel, skip to step (4).
b. If wiring will pass through RV wall at TOP of
back channel, mark wiring hole (notch) loca-
tion.
4. Move arm assemblies out of the way.
5. Drill 3/16″ diameter holes through marked
mounting hole locations and into solid structure
of RV.
Drill 7/32″ diameter holes if drilling into
steel.
INSTALL AWNING
6. Drill (1) 5/8″ diameter hole at marked TOP wiring
hole location and through outside wall of RV.
Skip this step if wiring will pass through
RV wall at BOTTOM of RH back channel.
7. With arm assembly completely closed, replace
top mounting brackets against wall and align its
mounting holes to the pre-drilled holes in RV.
8.  Control arm assemblies while in-
stalling brackets. When weight of FRTA is NOT
supported, downward force could cause arm as-
semblies to swing sideways and damage RV.
Apply sealant to #14 - 10 x 1-1/2″ hex head
screw threads. Then place and tighten (1) screw
through outside slot of top mounting bracket and
into solid structure of RV. See (FIG. 14).
Make sure arm assemblies are completely
closed before tightening outside screws.
Closed arm assemblies will help in the
overall alignment of awning.
FIG. 14
Awning
Rail
LH Top
Mounting
Bracket
#14 - 10 x 1-1/2″
Hex Head Screw
LH End Cap
9.  IMPACT OR PINCH HAZARD.
Arm assemblies are under tension from gas
strut. Hold arm assemblies and FRTA securely
BEFORE removing ties. Otherwise, arms will
extend quickly and unexpectedly. Failure to
obey this warning could result in death or seri-
ous injury.
While holding arm assembly (front channel) and
FRTA securely, carefully remove nylon ties (and
tape if applicable) around front and back chan-
nels. Then allow front channel to open slowly
until awning fabric is taut.
Slack from unfurled fabric will allow aw-
ning to open approximately 12″ - 18″.
10. Apply sealant to #14 - 10 x 1-1/2″ hex head
screw threads. Then place and tighten (1) screw
through inside slot of top mounting bracket and
into solid structure of RV. See (FIG. 15).

11
ther have a notch at top, or a hole near
bottom for wiring to pass through RV wall.
a. If wiring will pass through RV wall at TOP of
back channel, skip to step (4).
b. If wiring will pass through RV wall at BOT-
TOM of back channel, mark wiring hole loca-
tion.
4. Carefully swing arm assembly aside (out of the
way), to expose marked hole locations. See
(FIG. 17).
If arm is too stiff to swing aside, loosen
screw on inside slot of top mounting
bracket.
FIG. 17
Marked Hole Locations
RH Arm
Assembly
5. Drill 3/16″ diameter holes through marked
mounting hole locations and into solid structure
of RV.
Drill 7/32″ diameter holes if drilling into
steel.
6. Drill (1) 5/8″ diameter hole at marked BOTTOM
wiring hole location and through outside wall of
RV.
Skip this step if attaching LH back chan-
nel, or if wiring will pass through RV wall
at TOP of RH back channel.
7. Swing back channel back in place, and align its
mounting holes to the pre-drilled holes in RV.
Retighten screw on inside slot of top
mounting bracket (if loosened earlier to
swing arm assembly aside).
8. Apply sealant to 3/16″ x 1″ oscar rivets (custom-
er supplied). Then place rivets through bottom
(2) mounting holes of back channel and secure
to solid structure of RV. See (FIG. 18).
Structural backing (with skin) MUST be
3/8″ to 1/2″ thick to accommodate oscar
FIG. 15 Awning Rail
RH Top
Mounting
Bracket
#14 - 10 x 1-1/2″
Hex Head Screw
11. Repeat steps (3) through (10) for opposite side
for track and accessory wiring.
C. Attach Back Channels
1. Remove wiring cover from RH back channel (if
applicable). Save for reinstallation later.
2. Square back channel to RV and FRTA. Then
mark bottom mounting hole locations (LH and
RH back channels). See (FIG. 1) & (FIG. 16).
Measuring from a door or window frame is
acceptable.
FIG. 16
Floor Line
Back
Channel
Square
To RV
And
FRTA
FRTA
Center Mounting Holes
(1) Pair Above Strut
(1) Pair Below Strut
Bottom Mounting Holes
3. Wiring hole for motorized arm assembly. See
(FIG. 1).
The motorized arm assembly is ALWAYS
installed at the RH side of awning.
Wiring harness location is determined by
awning model. The back channel will ei-
INSTALL AWNING

12
ditional wiring instructions.
b. Connect motor wiring to the factory pre-
wired hardware wiring (near RH end cap).
See (FIG. 19).
c. Secure any slack motor / hardware wiring
inside front channel to prevent pinched or
damaged wiring during awning operation.
FIG. 19
RH End Cap
Motor Wiring
Hardware Wiring
2. POWER TRACK CONNECTIONS:
Power track wiring includes track and LED
strip.
a. Pull wiring through wiring hole (and grom-
met), and connect to appropriate wiring in-
side RV.
If grommet is NOT used, make sure
sealant will also provide effective and
permanent protection against wire
damage.
See instructions included with your
Dometic Corporation switch kit for ad-
ditional wiring instructions.
b. Connect power track / LED wiring to the fac-
tory pre-wired hardware wiring (near LH end
cap). See (FIG. 20).
c. Secure any slack power track / hardware wir-
ing inside front channel to prevent pinched
or damaged wiring during awning operation.
rivets.
Alternatively, structural screws (installer
supplied) may be used to secure back
channel if RV has structural backing that
will support at least 100 lb force per screw.
FIG. 18
3/16″ x 1″
Oscar Rivet
Back Channel
9. Repeat steps (1) through (8) for opposite side.
10. Apply sealant to #14 - 10 x 1-1/2″ hex head screw
threads. Then place and tighten screws through
remaining slots of both top mounting brackets
and into solid structure of RV. See (FIG. 14) &
(FIG. 15).
D. Electrical Connections To Awning
 Failure to obey the following notices
could damage product or property:
●Make sure the positive (+) 12 Vdc terminal is
disconnected from supply battery. Otherwise,
damage to unit could occur.
●ALWAYS seal wiring against weather and mois-
ture where wiring enters the RV’s walls, roof , or
oor. Otherwise, water leakage could occur.
●Do NOT pinch wiring or allow wiring to rub against
sharp edges. If wiring is damaged, it MUST be
replaced by a qualied service technician.
Use a grommet (installer supplied) when routing
wiring through RV wall.
If grommet is NOT used, use heat-shrink tub-
ing where wiring will pass through RV wall.
1. MOTOR AND SWITCH CONNECTIONS:
a. Pull wiring through wiring hole (and grom-
met), and connect to appropriate wiring in-
side RV.
If grommet is NOT used, make sure
sealant will also provide effective and
permanent protection against wire
damage.
See instructions included with your
Dometic Corporation switch kit for ad-
INSTALL AWNING

13
FIG. 20
LH End Cap
Power Track / LED Wiring
Hardware Wiring
3. LED RAIL LIGHT CONNECTIONS (IF
EQUIPPED):
Skip this step if awning is NOT equipped
with an LED light strip.
a. Pull wiring through wiring hole (and grom-
met).
If grommet is NOT used, make sure
sealant will also provide effective and
permanent protection against wire
damage.
b. Connect LED switch wiring to the factory
pre-wired LED light strip.
See instructions included with your
LED switch kit (installer supplied) for
additional wiring instructions.
c. Secure wiring to prevent pinching or other
damage during awning operation.
Allow enough slack in wiring to safely
accommodate possible fabric move-
ment.
4. COLOR CODES FOR WIRE CONNECTIONS
All wire connections should be made with
the power off. failure to do so could result
in unexpected operation or damage to the
product.
a. RH Arm (Motor End)
Red 12V +
Black 12V - (Ground)
b. LH Arm (For LED Awning)
White or Dark Red 12V +
Black 12 V - (Ground)
c. LH Arm (for Power Channel Awning)
White 12V + (to Power Channel)
Black 12V + (to LED in tube)
Green 12V - (Ground)
INSTALL AWNING
E. Complete Back Channel Installation
1. With power applied to awning, close awning (ful-
ly retract) to verify hardware is nesting correctly.
See “Close Awning” in Operating Instructions.
2.  PINCH HAZARD. Maintain a
horizontal distance of at least 16″ between fully
open awning and any permanent object. Failure
to obey this caution could result in injury.
Open awning (fully extend). See “Open Awning”
in Operating Instructions.
3. Verify back channel is still square to RV and
FRTA. See (FIG. 16).
4.  FIRE OR ELECTRICAL SHOCK
HAZARD. Make sure there are no obstacles
(wires, pipes, etc.) inside the RV’s roof, oor
and walls. Shut OFF gas supply, disconnect 120
Vac power from RV, and disconnect positive (+)
12 Vdc terminal from supply battery BEFORE
drilling or cutting into RV. Failure to obey these
warnings could result in death or serious injury.
5. Using (1) pair of center mounting holes as a
guide, drill 3/16″ diameter holes into solid struc-
ture of RV. See (FIG. 1) & (FIG. 16).
Wiring cover (if present) MUST be re-
moved from RH back channel to access
center mounting holes.
Center mounting holes may be above or
below strut.
Drill 7/32″ diameter holes if drilling into
steel.
6. Verify wiring (if applicable) is not caught be-
tween hardware and RV wall before tightening
fasteners
7. Apply sealant to 3/16″ x 1″ oscar rivets (cus-
tomer supplied). Then place rivets through back
channel (center mounting holes) and secure to
solid structure of RV. See (FIG. 18).
Structural backing (with skin) MUST be
3/8″ to 1/2″ thick to accommodate oscar
rivets.
Alternatively, structural screws (installer
supplied) may be used to secure back
channel if RV has structural backing that
will support at least 100 lb force per screw.
8. Repeat steps (3) through (7) for opposite side.
9. Replace wiring covers onto both back channels
(if applicable).
10. Reapply power to awning, and close awning
(fully retract).

14
F. Secure Awning Fabric To Awning Rail
1. With power applied to awning, open and close
awning four or ve times to allow natural self
adjustment of awning fabric. See Operating In-
structions.
2. Verify alignment of awning fabric, and proper
nesting of hardware.
a. If there is misalignment, adjust arm assembly
by loosening back channel and top mounting
bracket screws and move back channel ac-
cordingly. (Retighten screws.)
b. Cycle awning again to check alignment.
3. Ensure arm assemblies are still nested correct-
ly, then mark location of awning fabric edges on
awning rail.
4. Pull one edge of awning fabric approximately
1/4″ beyond marked position. Then secure with
#6 x 7/16″ TEK screw through awning rail (ap-
proximately 2″ from fabric edge). See (FIG. 21)
INSTALL AWNING
VERIFY INSTALLATION
C. Keep Literature
Instructions contain valuable information for prod-
uct use and consumer safety.
Keep BOTH the Installation and OperatIn-
stall Awning
FIG. 21
2″
Awning Rail
Fabric Edge
#6 x 7/16″
TEK Screw
5. Pull to stretch opposite edge of awning fabric
approximately 3/4″. Then secure with #6 x 7/16″
TEK screw through awning rail (approximately
2″ from fabric edge).
A. Test Operation
With power applied to awning, operate awning ac-
cording to Operating Instructions to verify all parts
are functioning correctly.
B. Secure Awning For Travel
1. Fully close awning. See “Close Awning” in Oper-
ating Instructions.
2. Verify awning is secure for travel. See “Prepare
Awning For Travel” in Operating Instructions.