Dometic 9100 User manual

Read these instructions carefully. These
instructions MUST stay with this product.
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
RECORD THIS INFORMATION FOR FUTURE
REFERENCE:
FRTA Model Number
FRTA Serial Number
Hardware Model Number
Hardware Serial Number
Date Purchased
Retailer / Qualied Installer
9100
POWER CHANNEL AWNING
LED TUBE AWNING
HARDWARE
8956(X)(X)1.4(X)0(#) BASEMENT
8956(X)(X)2.4(X)0(#) STANDARD
8956(X)(X)3.4(X)0(#) REDUCED PITCH
FRTA
FABRIC ROLLER TUBE ASSEMBLY
601FFLL.000(#)
91XFFLL.000(#)T
REVISION A
Form No. 3316037.000 10/16
(French 3316038.000_A)
©2016 Dometic Corporation
LaGrange, IN 46761
OPERATING
INSTRUCTIONS

2
TABLE OF CONTENTS
INTRODUCTION....................................................................................................................................................................2
DOCUMENT SYMBOLS ........................................................................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS................................................................................................................................3
A. Recognize Safety Information ...................................................................................................................................3
B. Understand Signal Words..........................................................................................................................................3
C. Supplemental Directives............................................................................................................................................3
D. General Safety Messages .........................................................................................................................................3
OPEN AWNING......................................................................................................................................................................4
SET AWNING POSITION.......................................................................................................................................................4
A. Adjust Awning Pitch (Optional) ..................................................................................................................................4
B. Prepare Awning To Shed Water.................................................................................................................................5
FEATURES AND ACCESSORIES .........................................................................................................................................6
A. Operate Tube LED Light Strip (If Equipped)..............................................................................................................6
B. Operate Rail LED Light Strip (If Equipped)................................................................................................................6
C. Operate Power Channel (If Equipped) ......................................................................................................................6
D. Attach Accessories To Power Channel......................................................................................................................6
E. Operate Accessories .................................................................................................................................................7
F. Remove Accessories From Power Channel ..............................................................................................................7
CLOSE AWNING....................................................................................................................................................................7
A. Close Awning.............................................................................................................................................................7
B. Prepare Awning For Travel ........................................................................................................................................8
CLOSE AWNING MANUALLY (POWER FAILURE)...............................................................................................................8
A. Auxiliary Power Method.............................................................................................................................................8
B. Pull Strap Method ......................................................................................................................................................9
GENERAL CARE AND USE.................................................................................................................................................10
A. Precautions..............................................................................................................................................................10
B. Hardware Maintenance ...........................................................................................................................................10
C. Fabric Maintenance .................................................................................................................................................10
D. When To Get More Help .......................................................................................................................................... 11
INTRODUCTION
This awning (hereinafter referred to as “awning,” or “product”) is designed and intended for use on RVs with straight sides.
For curved sides, please see the separate Hardware List in the Dealer Service Manual for the appropriate model. Use these
instructions to ensure correct operation of product.
Dometic Corporation reserves the right to modify appearances and specications without notice.
DOCUMENT SYMBOLS
Indicates additional information that is NOT related
to physical injury. Indicates step-by-step instructions.

3
IMPORTANT SAFETY INSTRUCTIONS
This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries.
A. Recognize Safety Information
This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
B. Understand Signal Words
A signal word will identify safety messages and
property damage messages, and will indicate the
degree or level of hazard seriousness.
 indicates a hazardous situation that,
if NOT avoided, could result in death or serious in-
jury.
 indicates a hazardous situation that,
if NOT avoided, could result in minor or moderate
injury.
 is used to address practices NOT
related to physical injury.
C. Supplemental Directives
Read and follow all safety information and
instructions to avoid possible injury or death.
Read and understand these instructions be-
fore [installing / using / servicing / performing
maintenance] on this product.
Incorrect [installation / operation / servicing /
maintaining] of this product can lead to seri-
ous injury. Follow all instructions.
The installation MUST comply with all ap-
plicable local and national codes, including
the latest edition of the following standards:
U.S.A.
● ANSI/NFPA70, National Electrical Code
(NEC)
● ANSI/NFPA 1192, Recreational Vehicles
Code
CANADA
●CSA C22.1, Parts l & ll, Canadian Electri-
cal Code
●CSA Z240 RV Series, Recreational
Vehicles
D. General Safety Messages
 Failure to obey the following warn-
ings could result in death or serious injury:
●This product MUST be [installed / serviced] by a
qualied service technician.
●Do NOT modify this product in any way. Modica-
tion can be extremely hazardous.
● Frequently examine product for imbalance (un-
even t / sagging / loose parts); and signs of wear
or damage to wiring (if applicable) and other criti-
cal parts. Do NOT use product if adjustments or
repairs are necessary.
Critical parts may include awning fabric,
cables, arm assemblies, etc.
●Disconnect product from power supply (if ap-
plicable), and do NOT operate product when
maintenance (such as window cleaning) is being
carried out in the vicinity.
●Do NOT allow anyone (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge to use this
product, unless they have been given supervision
or instruction (concerning use of this product) by
a person responsible for their safety.
●Do NOT allow children to play with product or with
xed controls (if applicable). Keep remote controls
(if applicable) away from children.
●IMPACT OR CRUSH HAZARD. NEVER leave an
open awning unattended. Keep awning stowed
(closed) when snow, heavy rain, wind, and severe
weather conditions are expected.
● IMPACT OR CRUSH HAZARD. Do NOT allow
water to pool, snow to accumulate, or heavy
debris on awning fabric. Do NOT hang or place
anything on awning. The awning will become
unstable, and could bend or collapse.
● FIRE HAZARD. Keep sources of heat and re
(barbecue grills, portable heater, etc.) away from
awning.
 PINCH HAZARD. Maintain a hori-
zontal distance of at least 16″ between fully open
awning and any permanent object. Failure to obey
this caution could result in injury.
Do NOT face awning toward permanent
objects that may interfere with awning op-
eration.

4
1.  PINCH HAZARD. Maintain a
horizontal distance of at least 16″ between fully
open awning and any permanent object. Failure
to obey this caution could result in injury.
Press and hold toggle up (extend) on awning
switch until awning extends to its out position.
See (FIG. 1).
Awning will stop when button is released
no matter how far awning is extended / re-
tracted.
Switch
Appearance
May Vary
OFFON
Stop ONON
Track and LED Switches
Awning Switch
FIG. 1
2.  IMPACT OR CRUSH HAZARD.
Do NOT allow awning to remain in over-extend-
ed position as this could trap heavy debris, or
could cause water to pool or snow to accumu-
late on awning fabric. This weight will cause aw-
ning to become unstable, and bend or collapse.
Failure to obey this warning could result in death
or serious injury.
Verify valance is in correct position, and adjust
if necessary. If awning is over-extended, press
toggle down (retract) briey on awning switch
until valance is in correct position. See (FIG. 1)
& (FIG. 2).
FIG. 2
Wrong Position.
Awning Is Over-
Extended With
Valance Rope
Behind Roller
Tube.
Correct Position.
Awning Is
Extended
Correctly With
Valance Rope
At Top Of Roller
Tube.
OPEN AWNING
SET AWNING POSITION
A. Adjust Awning Pitch (Optional)
The FRTA (fabric roller tube assembly) will be lower
than RV’s awning rail when hardware is fully ex-
tended. This pitch (slope) will help accommodate
water runoff. If a steeper pitch is desired, the FRTA
must be lowered.
To lower FRTA:
1. With awning fully extended, loosen adjustable
knob on adjustable pitch arm assembly (bottom
arm). See (FIG. 3).
2. Press in on spring loaded button on right side of
adjustable pitch arm assembly to allow adjust-
ment. See (FIG. 3) & (FIG. 4).

5
4. While holding top arm assembly in place, tighten
adjustable knob to set pitch (slope). See (FIG. 3)
& (FIG. 4).
5.  IMPACT OR CRUSH HAZARD.
ALWAYS lower one side of hardware into wa-
ter shed position when adjusting awning [pitch
/ slope]. Otherwise, water could pool on awning
fabric. Failure to obey this warning could result
in death or serious injury.
Repeat steps (1) through (4) for opposite side.
Make sure the top arm assembly that’s far-
thest from entry door is lowered more than
the other. See subsection, “B. Prepare
Awning To Shed Water” on page (5).
B. Prepare Awning To Shed Water
 IMPACT OR CRUSH HAZARD. Do
NOT allow water to pool or snow to accumulate
on awning fabric. The awning will become unsta-
ble, and could bend or collapse. Whenever heavy
rain or snow is expected, place awning in stowed
(closed) position. Failure to obey this warning could
result in death or serious injury.
Lowering one arm assembly into water shed posi-
tion (to create a slope from other arm assembly) will
allow water run-off during light rain.
1. With awning fully extended, verify top arm as-
sembly nearest entry door is fully extended, and
that adjustable knob is tightened. See (FIG. 3).
2.  IMPACT OR CRUSH HAZARD.
NEVER disengage adjustable knob during
windy conditions, or with water pooled or snow
accumulated on awning fabric. This could cause
the awning to move unpredictably, become un-
stable, and bend or collapse. Failure to obey this
warning could result in death or serious injury.
 Do NOT allow corner of entry
door to contact awning fabric. Otherwise, pre-
mature wear or tearing of awning fabric could
occur.
Loosen adjustable knob on adjustable pitch arm
assembly (bottom arm) that’s farthest from entry
door. See (FIG. 3).
Lowering the arm assembly that’s nearest
entry door could allow door to contact fab-
ric. If awning pitch was previously adjust-
ed lower, raising arm nearest entry door
will provide more fabric clearance.
3. Press in on spring loaded button on right side of
adjustable pitch arm assembly to allow adjust-
ment. See (FIG. 3) & (FIG. 4).
FIG. 3
Adjustable
Pitch Arm
Assembly
Front Channel
Adjustable Knob
Spring Loaded Button
3.  PINCH HAZARD. Keep CLEAR
of openings around adjustable pitch arm assem-
bly while adjusting awning pitch (slope). Adjust-
able pitch arm assembly (bottom arm) will tele-
scope. Failure to obey this caution could result
in injury.
 Do NOT allow corner of entry
door to contact awning fabric. Otherwise, pre-
mature wear or tearing of awning fabric could
occur.
Pull top arm assembly down to lower FRTA to
desired height. See (FIG. 4).
FIG. 4
Adjustable
Pitch Arm
Assembly
Top Arm
Assembly
Spring Loaded
Button
SET AWNING POSITION

6
FIG. 5
10° Slope
(Or 9″ Minimum)
Awning Rail
Arm Assembly
5. While holding top arm assembly in place, tighten
adjustable knob to set in place. See (FIG. 3) &
(FIG. 4).
4.  PINCH HAZARD. Keep CLEAR
of openings around adjustable pitch arm assem-
bly while adjusting awning pitch (slope). Adjust-
able pitch arm assembly (bottom arm) will tele-
scope. Failure to obey this caution could result
in injury.
Pull top arm assembly (farthest from entry door)
down until awning slopes approximately 10°,
or 9″ minimum from other arm assembly. See
(FIG. 4) & (FIG. 5).
This slope requirement is in addition to the
slope from RV’s awning rail.
SET AWNING POSITION
FEATURES AND ACCESSORIES
A. Operate Tube LED Light Strip (If
Equipped)
1. Turn tube LED switch to ON position to illumi-
nate tube LED light strip. LED indicator light on
switch plate will illuminate. See (FIG. 1).
Do NOT use tube LED light strip while aw-
ning is closed.
2. Turn tube LED switch to OFF position when tube
LED light strip is not in use. LED indicator on
switch plate will turn off.
B. Operate Rail LED Light Strip (If Equipped)
Rail LED switch operation and appearance
may vary depending on application.
1. Turn rail LED switch to ON position to illuminate
rail LED light strip.
Rail LED light strip may be used while aw-
ning is open or closed.
2. Turn rail LED switch to OFF position when rail
LED light strip is not in use.
C. Operate Power Channel (If Equipped)
1. Turn power channel switch to ON position to
supply power to tube power channel. Power
channel indicator light on switch plate will illumi-
nate. See (FIG. 1).
Do NOT use tube power channel while
awning is closed.
2. Turn power channel switch to OFF position to
disengage power from tube power channel. LED
indicator on switch plate will turn off.
Attached accessories will NOT function
while switch is in OFF position.
D. Attach Accessories To Power Channel
1. Align power bayonet with power channel slot.
See (FIG. 6).
2. Insert power bayonet fully into power channel
slot, pushing on accessory base (alignment in-
dicator). See (FIG. 6).
FIG. 6
Power
Channel Slot
Alignment Indicator
Power Bayonet
Base Cover

7
FEATURES AND ACCESSORIES
3.  Make sure alignment indicator on
accessory base is pointed upward after install-
ing into power channel. Otherwise, damage to
accessory or power channel could occur.
Rotate base 90°, so longest lobe of power bayo-
net, and alignment indicator, are pointed up-
ward. See (FIG. 7).
FIG. 7
Alignment Indicator
Base Cover
Alignment Lug
4. When accessory base is properly aligned, align-
ment lugs on sides of base cover will sit into
power channel slot, providing a positive lock.
See (FIG. 7).
E. Operate Accessories
See Instructions included with power channel
accessories (if applicable).
F. Remove Accessories From Power
Channel
1. While pulling back on spring loaded, scalloped
base cover, rotate base 90° (alignment indicator
in line with power channel slot). See (FIG. 8).
FIG. 8
Power
Bayonet
Base Cover
Power
Channel Slot
Alignment Indicator
2. Remove accessory from power channel slot and
release spring loaded base cover. See (FIG. 8).
CLOSE AWNING
A. Close Awning
1. Remove ALL accessories from power channel.
See “F. Remove Accessories From Power
Channel” on page (7).
2. Loosen adjustable knobs and ensure awning re-
sets to original position and spring loaded button
engages. Then lightly tighten knobs on both arm
assemblies to help ensure rattle-free travel. See
(FIG. 3).
Pull top arm assembly down to verify knob
is NOT too tight. Adjustable pitch arm as-
sembly MUST still slide as normal. See
(FIG. 4).
3. Ensure power channel and LED light strip
switches are in the “OFF” position.
4.  PINCH HAZARD. Keep CLEAR
of arm assemblies while closing awning. Arm as-
semblies will [fold / close] against back channel.
Failure to obey this warning could result in death
or serious injury.
Press and hold toggle to retract (ON) position on
(xed / wired) remote awning switch until awning
is fully closed. See (FIG. 1) & (FIG. 9).
Awning will stop when button is released
no matter how far awning is extended / re-
tracted.

8
With awning fully closed, Test ignition interlock
system:
Testing of ignition interlock system is only
applicable to motorhomes.
a. With vehicle ignition in ON position, attempt
to open awning.
b. If awning does NOT respond (remains
closed), the ignition interlock is functioning.
Skip to step (3).
c. If awning responds to switch (awning opens),
there is a problem with the ignition interlock
system. Proceed to step (2).
2. Disable awning for travel to service center:
a. Close awning and remove fuse for power
source to awning.
b. Retest ignition interlock. See step (1).
c. If awning does NOT respond (remains
closed), the awning is now disabled. Skip to
step (f).
d. If awning still operates, pull motor connector
from hardware connector to disconnect mo-
tor wiring. See (FIG. 10).
The motor connector may be hard to
reach when awning is closed. Pull wir-
ing at RH top casting until wires dis-
engage.
e. Repeat step (1) to verify motor is disabled.
f. Have awning repaired by a qualied service
technician.
3. Turn LED light strip (if equipped) OFF before
travel. See “A. Operate Tube LED Light Strip (If
Equipped)” on page (6).
4. Verify awning is secure for travel.
Look for loose parts, and any sign of in-
stability.
FIG. 9
Front Channel
Back Channel
Adjustable
Arm Assembly
Top Arm
Assembly
Pinch
Points
Pinch
Points
Pinch
Point
B. Prepare Awning For Travel
1.  IMPACT OR CRUSH HAZARD.
Make sure ignition interlock is working correctly
before traveling with RV. If awning responds to
switch with ignition in ON position, accidental
operation during transit could occur. The awning
MUST be disabled, then serviced by a qualied
service technician. Failure to obey this warning
could result in death or serious injury.
CLOSE AWNING
CLOSE AWNING MANUALLY (POWER FAILURE)
In case of power failure, it may be necessary to close
awning manually. There are two methods to close awning
manually:
Perform procedure under, “A. Auxiliary Power Method” on
page (8) rst. If this fails, perform procedure under, “B.
Pull Strap Method” on page (9).
Rule out simple causes for power failure (RV dis-
connected from power, blown fuse, low/discharged
battery, ignition interlock, etc.) before attempting
to close awning manually. After awning is closed
manually, it will require service by a qualied
service technician.
The LED light strip (if equipped) is on a separate
circuit from awning motor. If LED lights work, but
awning motor does not, check awning motor’s fuse
(at fuse panel or converter) before closing awning
manually.
A. Auxiliary Power Method
When awning is in open position and 12 Vdc power
has been lost, the awning may be closed by sup-
plying auxiliary power (from external source) to aw-
ning motor.
A 12 Vdc automobile battery may be used as
an external power source.

9
6. If awning does not move (after conrming con-
nections and charge on external power source),
the motor may be defective. Proceed to subsec-
tion, “B. Pull Strap Method” on page (9) for
alternative method.
B. Pull Strap Method
Use this procedure if prior method failed to close
awning.
This procedure requires a 5/32″ hex key, and
help from at least one other person.
1. Make sure adjustable knobs are only lightly
tightened on both arm assemblies. See (FIG. 3).
2. Make sure motor connector is unplugged from
hardware connector (located in upper part of RH
arm assembly). See (FIG. 10).
3. Insert pull strap (provided) into utility slot of
FRTA, and slide to center (of FRTA). See
(FIG. 11).
FIG. 11
(2) Screws In
Top Casting
4.  IMPACT OR PINCH HAZARD.
Hold pull strap rmly before removing screw(s)
at top casting. The fabric roller tube is under
spring tension, which will attempt to close the
awning quickly and unexpectedly. Failure to
obey this warning could result in death or seri-
ous injury.
While one person grasps pull strap rmly, remove
the (2) screws at top and back of RH top casting.
Save for reinstallation later. See (FIG. 11).
5.  PINCH HAZARD. Keep CLEAR
of arm assemblies while closing awning. Arm as-
semblies will [fold / close] against back channel.
Failure to obey this warning could result in death
or serious injury.
 Move pull strap diagonally (to left
or right) as awning rolls up. Otherwise, awning
fabric may crease or form a bulge, and could
permanently stretch fabric.
1. Loosen adjustable knobs to allow awning to
reset to original position. Then lightly tighten
knobs on both arm assemblies to help ensure
rattle-free travel. See (FIG. 3).
2.  ELECTRICAL SHOCK HAZARD.
Disconnect power from product before access-
ing wiring connections. There may be issues
mimicking a power failure with electric current
still present, or power may return unexpectedly.
Failure to obey this warning could result in death
or serious injury.
Disconnect 120 Vac power from RV, and 12 Vdc
power to awning.
3. Unplug motor connector from hardware connec-
tor (located in upper part of RH arm assembly).
See (FIG. 10).
FIG. 10
RH End Cap
Motor Connector
Hardware Connector
4. Connect 16 Gauge (minimum) wire leads (user
supplied) to motor connector, and tape in place
(with electrical tape).
Do NOT connect to hardware connector.
Match wire lead colors to motor wire col-
ors (black to black, red to red).
5.  Disconnect power IMMEDIATE-
LY after awning retracts. Otherwise, damage to
awning motor could occur.
Connect other end of wire leads to the 12 Vdc
external power source, until awning retracts to
its closed position:
a. Connect red wire to positive (+) terminal.
The lead wire connected to positive
(+) terminal MUST have a (3 A) in-line
fuse installed.
b. Connect black wire to negative (-) terminal.
c. Disconnect wire leads from power source
once awning fully retracts.
The awning will extend if wire leads are
reversed (reversed polarity).
CLOSE AWNING MANUALLY (POWER FAILURE)

10
C. Fabric Maintenance
Vinyl fabric offers the advantage of durability and
water resistance.
Wrinkling is a normal characteristic of vinyl.
Wrinkling may be more noticeable when re-
tracted, and after prolonged periods of stow-
age (rolled up). Leave awning open during
warm weather to minimize the wrinkling over
a period of time.
1. To clean:
a. Mix 1/4 cup dish soap and 1/4 cup bleach to
5 gallons of fresh water to use as cleaning
solution.
b.  Do NOT use abrasive or cor-
rosive cleaners, mildew removers, or hard
bristle brushes on awning fabric.
Liberally drench open awning fabric with
cleaning solution.
c. Close awning, let it soak for 5 minutes, then
open awning again.
d.  Remove solution COM-
PLETELY from awning fabric. Bleach will
degrade awning fabric if NOT completely
rinsed off.
Thoroughly hose off top and bottom of fabric
with clean water.
Repeat as necessary to completely re-
move solution.
e.  NEVER close awning (for
storage) when wet. The combination of
moisture and dirt could result in mildew, dis-
coloration, and stains.
Allow awning to dry thoroughly before stow-
ing (rolling up).
2. To repair a pinhole, or if a spot of coating akes
off from top layer of vinyl fabric:
a. Apply a very small dab of VLP (Vinyl Liquid
Patch) on tip of cotton swab.
VLP is available from Dometic Cor-
poration. Reference part number
3314216.000 when ordering.
A. Precautions
 Failure to obey the following notices
could damage product or property:
●Do NOT use insecticides or other sprays near aw-
ning fabric. These could cause stains, and could
adversely affect fabric’s ability to repel water.
●Do NOT expose awning to adverse environmental
conditions, corrosive agents, or other harmful
conditions.
●Do NOT allow corner of entry door to contact aw-
ning fabric. Otherwise, premature wear or tearing
of awning fabric could occur.
●NEVER close awning (for storage) when wet. The
combination of moisture and dirt could result in
mildew, discoloration, and stains.
If it is necessary to roll up awning (tem-
porarily) while it’s wet, make sure you roll
it out and let it dry (as soon as conditions
allow) before rolling it up again.
●Do NOT allow dirt, leaves, or other debris to ac-
cumulate on awning, which could cause abrasion
and stains. Mildew could grow on dirt and organic
debris causing permanent discoloration, stains,
and odors to awning fabric.
B. Hardware Maintenance
1.  Do NOT use strong chemicals or
abrasives to clean parts, as their protective sur-
faces will be damaged.
Clean awning hardware (as needed) with a mild
surface cleaner.
2.  Do NOT use silicone sprays near
labels. Otherwise, the label’s adhesive bond to
product surfaces could weaken.
Apply silicone spray lubricant as needed to keep
the fabric roller tube assembly’s moving parts
operating smoothly.
3. Lubricate all sliding surfaces of arm assemblies
with silicone spray as needed.
CLOSE AWNING MANUALLY (POWER FAILURE)
Carefully and slowly allow awning to roll up
(close).
6.  IMPACT OR CRUSH HAZARD.
Reinstall screw(s) at top casting BEFORE trans-
porting RV. Otherwise, awning could extend
quickly and unexpectedly during transit. Failure
to obey this warning could result in death or seri-
ous injury.
Align holes in RH top casting (where screws
were removed), and reinstall the (2) screws to
secure awning for travel.
Do NOT reattach wiring. Awning will require
service by a qualied service technician.
GENERAL CARE AND USE

11
D. When To Get More Help
If malfunctions occur (that cannot be corrected by
reviewing these instructions), contact a qualied
service technician.
A slight “travel line” may appear where door
roller (if installed) contacts awning fabric.
This is considered normal and does NOT af-
fect the integrity of awning fabric.
b. Gently roll cotton swab around pinhole. The
VLP will melt the coating (on fabric) and that
will quickly ll in pinhole and blend with all
colored vinyls.
c.  NEVER close (roll up) awning
when vinyl liquid patch is wet. Otherwise,
damage to other parts of awning fabric (melt-
ing through layers) will occur.
Allow VLP to dry thoroughly before stowing
(rolling up) awning.
GENERAL CARE AND USE