Dorma 8916 AF89 PFT User manual

45°
PAGE
INS NO. Rev.
08279761 09/09
1 of 2
www.dorma-usa.com 1-800-523-8483
Install PFT bracket to transom.
AND ACCESSORY PLATE DP89
8916/8956 AF89 PFT
PARALLEL ARM MOUNT WITH FLUSH TRANSOM
1
2
3
as shown.
DP89 Plate applications only. Attach plate to door
WOOD DOORS
SN1 (Sex Nuts)
METAL DOORS or
QTY
(4)
(4)
QTY
(RH DOOR)
(LH DOOR)
adjustment facing hinges.
Attach closer to door or plate with spring
(LEFT HAND DOOR)
HINGESC
L
PLATE
METAL DOORS or SN1 (Sex Nuts)
WOOD DOORS
(RIGHT HAND DOOR)
QTY
(4)
(4)
QTY
QTY
(4)
HINGES
L
C
according to template.
Determine hand of door. Prepare door and frame
(REFERENCE UNIT CARTON FOR ACCESSORIES AND
OPTIONS SUPPLIED)
LISTINGS.
IDENTIFIED IN THE INDIVIDUAL DOOR MANUFACTURER'S
DOORS, UNLESS AN ALTERNATIVE METHOD IS
WOOD OR PLASTIC FACED COMPOSITE TYPE FIRE
OF COMPONENTS TO UNREINFORCED DOORS AND TO
CAUTION: SEX NUTS ARE REQUIRED FOR ATTACHMENT
REVERSE BEVEL
RIGHT HAND DOOR
LEFT HAND DOOR
REVERSE BEVEL
RIGHT HAND LEFT HAND QTY
(1)
Install connecting arm bolt, leaving bolt loose.
Slide bar into connecting arm.
Install arm shoe to bracket.
14"
QTY
(2)
Insert bolt in this hole.
rotate pinion 45° TOWARD HINGE edge of door.
Place wrench on bottom pinion and
Install main arm.
QTY
(4) QTY
(4)
METAL FRAMES WOOD FRAMES
Adjust overall length to 14".
7
5
6
4
INSPK NO. 08279760 Rev.09/09

SNAP VALVE ADJUSTMENT
WRENCH INSIDE COVER
08279761 2 of 2 09/09
INS NO. PAGE Rev.
CAUTION: DO NOT REMOVE VALVES.
Adjust sweep and latch valves.
Closing time from 90° to 15° (sweep range) is
generally adjusted to take a minimum of 3 seconds.
Closing time from 15° to fully closed (latch range)
should take a minimum of 1.5 seconds.
hex key.
the door. All valve adjustments are made with a 3/32"
Optional delayed action offers additional closing speed
control when extra time is required to pass through
10
11
RIGHT HAND IS A MIRROR IMAGE.
NOTE: LEFT HAND DOOR
INSTALLATION SHOWN.
PINION
PINION SCREW
L HINGE
C
ROTATE
PINION
45°
6mm HEX KEY
9
Adjust according to chart.
ADJUSTER
FULL TURNS
OF SPRING
0
+4
+12
FULL TURNS
OF SPRING
ADJUSTING NUT
ADJUST SPRING TENSION ACCORDING TO THE FOLLOWING CHART.
8916
8956
CLOSER
ULC LABELED UNITS ONLY
TYPE
200
200 6
5
6
0
SIZE
SPRING
DOOR
WEIGHT
150
100
125
MAX.
3
4-12
NON-BARRIER-FREE OPENINGS -
3'-6"
3'-6"
3'-0"
2'-6"
EXTERIOR
TYPE
8916
8956
CLOSER
INTERIOR
2'-6"
4'-0"
3'-6"
3'-0"
4'-0"
-
+4
0
+12
-12
0
DOOR WIDTH
5
6
6
3
4
SPRING
SIZE
Take an opening force reading from
the pull on the door. If required, adjust the spring tension
to meet the barrier-free requirement. Maximum number of
adjusted to meet barrier-free forces may not have sufficient
power to reliably close and latch the door.
turns counter clockwise=8. Maximum number of turns
clockwise =14. Depending on opening conditions, a door
BARRIER-FREE OPENINGS -
8916 ONLY
ADJUSTER
Adjust spring tension, if required, using a 1/4" wrench.
8956 supplied with size 6 setting.
8916 supplied with size 4 spring setting.
SPRING TENSION
CRITICAL
NOTE:
+
-
5
-6
3'-6"3'-0"
-6
5
150
-4'-0" +6 6+
250 6+ +6
BAR MAIN ARM
CONNECTING ARM
TOUCH DOOR). Tighten connecting arm bolt securely
With door closed, adjust connecting arm length until
main arm is parallel to door. MAIN ARM SHOULD NOT
with 1/2" wrench.
LATCH
BACKCHECK OR DELAYED ACTION
NOTE: DELAYED ACTION IS AN OPTIONAL FEATURE.
SWEEP (SPEED)
DECREASE
INCREASE
(SPEED) (TIME)
BACKCHECK (INTENSITY)
BACKCHECK RANGE
DELAYED ACTION
RANGE
DELAYED
ACTION
POSITIONING VALVE
SWEEP & LATCH
SWEEP
RANGE
LATCH
RANGE
INCREASE
DECREASE
(2)
TAB
QTY
NOTE: LEFT HAND INSTALLATION SHOWN. RIGHT
HAND IS A MIRROR IMAGE.
Placecoverovercloserandfastensecurelywith
Placetabincoverslotoppositemainarm.
screwsprovided.
(1)
QTY
8With main arm parallel to door, place main
arm onto top pinion. Fasten securely with
pinion screw.