Dorma EMR Series User manual

1 2
Remove (1) wire access plug according to
Install closer to door.
8600PT
(LEFT HAND DOOR)
8600T AND 8600DE
(RIGHT HAND DOOR)
(RIGHT HAND DOOR)
(LEFT HAND DOOR)
QTY
(4)
the installation type. Any access hole can be used for
T & DE (RH)
T & DE (LH)
ON PT MOUNTS
NOTE: NO TOP PLUG
surface wiring installations.
SURFACE WIRING
C
L
C
L
L
CC
L
8600 EMF SERIES
Each (HO) hold open unit contains a door closer and track assembly with hold open electromagnet.
The unit can be connected directly to a fire control panel.
1.
Read entire instruction sheet prior to installation and refer to NFPA 72E. Standards may be obtained from
THE NATIONAL FIRE PROTECTION ASSOCIATION, Batterymarch Park, Quincy, MA., 02269.
2. Reference unit carton for mounting style and voltage.
3.
Prepare door and frame for fasteners using the appropriate template. Mark, drill and tap holes as indicated.
If surface wiring is used, omit 7/8" hole for wire access.
NOTE:
Three access wire
holes on optional
surface wired units only.
INSPK NO. 08280570 Rev.08/13
INS NO.
Rev.
08281020
08/13
PAGE
1 of 5
www.dorma-usa.com 1-800-523-8483

3
THIS CONNECTION IS NOT POLARITY DEPENDENT.
INCOMING POWER
SOLENOID WIRES
NOTE:
CAUTION:
WIRE CONNECTION COVER
QTY
(2)(2)
QTY
Install with wire access plugs toward latch edge of door using (2) 1/4-20 x 2" metal or (2) No. 14 x 2-3/4" wood screws.
Route wires from frame through appropriate wire access hole in track, being careful not to pinch wires during installation.
8600PT
8600T and 8600DE
Install track to frame.
QTY
(1)
4
5
8600PT ONLY
C HINGE
(1)
QTY
Install remaining screw as shown using 1/4-20 x 2" metal or No. 14 x 2-3/4" wood screw.
Insert cover into track, align end cap in end of track.
COVER
END CAP
NOTE:
Improper voltage to unit, will result in damage to unit and void warranty.
All wiring must comply with national,
state and local electrical codes.
U.L. LISTED
ALARM CONTROL UNIT OR
SMOKE DETECTOR
SMOKE DETECTOR
ALARM CONTROL UNIT OR
U.L. LISTED
QTY
(1)
QTY
(1)
END CAP
END CAP
END CAP
CONNECTION
TERMINAL
BLOCK
TERMINAL BLOCK 18awg MAX.
Slide wiring connection cover to allow access to wire connections.
Determine power supply and unit voltage type: 24VAC/24VDC. CAUTION!!! DO NOT CONNECT 120VAC TO A 24 VOLT
UNIT TYPE. Connect power supply wires to terminal block as shown (Terminal Block can be removed for easier access).
Return wiring connection cover to cover wire connections.
Install PT track to soffit with wire access plugs toward hinge. Install with (1) 1/4-20 x 1-1/4" combo screw and (1) 1/4-20 x 2"
metal or No. (1) 14 x 2-3/4" wood screw as shown. Route wires from frame through appropriate wire access hole in track,
being careful not to pinch wires during installation. ( DO NOT INSTALL END CAP ON HINGE SIDE IN THIS STEP)
(1)
QTY
INS NO.
PAGE
Rev.
08281020
2 of 5
08/13

7
Attach arm to slide shoe. Use 3/16 inch hex head wrench.
Attach main arm to door closer.
With door in closed position, rotate bottom pinion 45° with wrench. Place arm on top pinion.
Place arm on top pinion as shown @45° angle. Secure with pinion screw and washer.
8600PT
Open door and secure with pinion screw and washer.
(RIGHT HAND DOOR)
8600T
(LEFT HAND DOOR)
6
8600DE
Place arm on top pinion as shown @45° angle. Secure with pinion screw and washer.
(RIGHT HAND DOOR)
(LEFT HAND DOOR)
3/16 HEX KEY 3/16 HEX KEY
(1)
QTY
3/16 HEX KEY 3/16 HEX KEY
(1)
QTY
QTY
(1)
HINGE C
C HINGE
(LEFT HAND DOOR)
(RIGHT HAND DOOR)
45°
PINION
ROTATE
3/16 HEX KEY
PINION
ROTATE
45°
3/16 HEX KEY
INS NO.
PAGE
Rev.
08281020
3 of 5
08/13

9
8
NOTE: POWER MUST BE SUPPLIED TO RESET POSITION.
Loosen set screws using 3/32 inch hex wrench. Slide hold open device to desired position.
GREATER HOLD
Retighten set screws securely.
Hold open position is preset at approximately 90°.
OPEN ANGLE
10
HOLD OPEN SET SCREWS
3/32 HEX
HOLD OPEN DEVICE
LESS HOLD
OPEN ANGLE
-
+
3'-6" (1067)
2'-6" (762)
3'-0" (914) 3'-6" (1067)
4'-0" (1219)
Interior
2'-6" (762)
3'-0" (914)
-
Exterior
+5
+13
-11
0
+
-
150
5
6200
3
4
100
125
-
+
+
-
-
+
COV
FCSL
FC
FMC
-7
0
8616 8656
DO NOT REMOVE VALVES
S
L
Spring Size
BACKCHECK POSITIONING
Door Width
DA
Adjuster
Full Turns
ULC LABELED
UNITS ONLY
Max.
Door Weight
BC
ADJUSTABLE HOLD OPEN FORCE - 5/32 HEX
CLOCKWISE = STRONGER
INS NO.
PAGE
Rev.
08281020
4 of 5
08/13

and doors close.
4. Activate system into alarm so
electromagnet
s release
the units to return to standby.
Resetting the test switch will allow
will release and the doors will close.
delay, the hold open
electromagnet
of both units
procedure for that unit. After a short time
main closer detector as explained in the test
detectored unit, trip the test switch of the
5. If the closer is used in conjunction with a
3. Advise fire officials prior to testing.
2. Open door so slide block engages with hold
connections. Apply power to units.
1. After installation is completed, recheck all
Final installation and test.
11
open assembly.
14
shut the door.
open and allows the door closer to
contact will open and interrupt current
supply based on unit voltage.
applying, 24VDC/24VAC power
across a normally closed alarm contact
NORMAL- The closer unit's electromagnet will be energized
24VAC 166mA
Maximum input current- 24VDC 166mA
24VAC +10% -15%
Voltage input- 24VDC +10% -15%
ELECTRICAL SPECIFICATION
to the electromagnet which releases the hold
FIRE ALARM- When the alarm sounds, the alarm
OPERATION
AND MAINTENANCE TO RETAIN THE SYSTEM IN
USER IS ALSO RESPONSIBLE FOR THE ADJUSTMENTS
THE TESTING OF THE FIRE ALARM SYSTEM. THE END
THE INITIAL INSTALLATION TEST, IN CONJUNCTION WITH
SYSTEM MUST ALSO BE TESTED PERIODICALLY AFTER
WHEN THE ALARM SYSTEM IS ACTIVATED. THE ENTIRE
THAT THE DOOR CLOSER UNITS FUNCTION PROPERLY
INSTALLATION, BY THE END USER, TO ASSURE
IMPORTANT: THE UNIT MUST BE TESTED AFTER THE
WORKING ORDER.
13
12
WIRE CONNECTION COVER
Improper voltage to unit, will result in damage to unit and void warranty.
CAUTION:
All wiring must comply with national,
NOTE:
state and local electrical codes.
TERMINAL BLOCK 18awg MAX.
THIS CONNECTION IS NOT POLARITY DEPENDENT.
GROUND
BYPASS SWITCH
WIRE CONNECTION COVER
BLOCK
NOTE:
TERMINAL
SCREW
ALARM CONTROL UNIT OR
SMOKE DETECTOR
INCOMING POWER
CONNECTION
U.L. LISTED
BYPASS SWITCH
OPTIONAL:
An auxiliary door stop (by others) must be installed to limit the
maximum degree of door swing. Failure to do so may result in
damage to the unit.
Slide wiring connection cover to allow access. Attach bracket and assemble bypass switch.
Determine power supply and unit voltage type: 24VAC/24VDC. CAUTION (DO NOT CONNECT 120VAC TO A 24 VOLT
UNIT TYPE.) Connect power supply wires, one (1) to terminal block one (1) to bypass switch. connect other bypass switch wire to
terminal block (Terminal Block can be removed for easier access).
Return wiring connection cover to cover wire connections.
INS NO.
PAGE
Rev.
08281020
5 of 5
08/13