Dorma TS93 Series User manual

QTY
(1)
M5 HEX KEY M5 HEX KEY
(REFERENCE UNIT CARTON LABEL FOR ACCESSORIES AND OPTIONS SUPPLIED)
TS93 STH
PULL SIDE TRACK MOUNT
Determine hand of door and degree of deadstop required.
Prepare door and frame for fasteners
1
according to template 08280612.
2
3
4
LEFT HAND DOOR RIGHT HAND DOOR
Attach mounting plate to frame using lower four QTY
(4) WOOD
FRAME
METAL
FRAME
RIGHT HAND DOOR LEFT HAND DOOR
QTY
(4)
Attach closer to mounting plate.
RIGHT HAND DOOR LEFT HAND DOOR
RIGHT HAND DOOR
Attach arm to pinion of closer, parallel to door.
holes in plate. Arrows on plate point up.
LEFT HAND DOOR
Rev.08/09INSPK NO. 08280610
www.dorma-usa.com 1-800-523-8483 PAGE
Description:
INS NO. Rev.
08280611 08/09
1 of 3

METAL
QTY
(2) WOOD
DOOR
DOOR
2
143
ACTION
7Adjust sweep, latch, backcheck and delayed
action valves.
1 - SWEEP speed from
2 - LATCH speed from approx.
70° to 0°
7° to 0°.-(INCREASE ONLY)
DECREASE
INCREASE SWEEP
RANGE
LATCH RANGE
CAUTION: DO NOT REMOVE VALVES.
BACKCHECK RANGE
4 - DELAY speed from max opening 180° to 70°
CAUTION: DO NOT CLOSE VALVE COMPLETELY.
DECREASE
INCREASE
BACKCHECK (INTENSITY)
3 - BACKCHECK cushion effect.
DELAY
RANGE
screw and tighten securely. Install track cover.
Attach arm to slide shoe.
Align hole in arm with slide shoe in track. Insert
QTY
(1)
8
5/64" HEX KEY
5Assemble track and attach to door.
Attach track to door using track mounting screws.
Insert slide shoe and end blocks into track with spring block
near the hinge side of door frame.
HOLD OPEN ADJUSTMENT
ADDITIONAL INSTRUCTIONS (HOLD-OPEN UNITS):
hex key into the slide shoe bolt. Turn clockwise to increase
or counterclockwise to decrease holding force.
3. Open door until slide shoe engages with hold-open.
4. To release the door, pull until the slide shoe disengages.
2. Adjust the holding force by inserting a 5/64"
on, opposite direction off.
1. Adjust hold-open to on or off position. One direction
6
M5 HEX KEY
SPRING ON HINGE SIDE
08280611 2 of 3 08/09
INS NO. PAGE Rev.

END COVERS
8
adjusted to meet barrier-free forces may not have sufficient
Take an opening force reading from
CAUTION: DO NOT OVERTIGHTEN
to meet the barrier-free requirement. Maximum number of
clockwise =12. Depending on opening conditions, a door
turns counter clockwise=5. Maximum number of turns
power to reliably close and latch the door.
ULC LABELED UNITS "ONLY"
NON-BARRIER-FREE OPENINGS:
Adjust according to chart.
Adjust according to chart.
Adjust spring tension, if required.
TS93-1 supplied with a size 2 spring setting.
CRITICAL
the pull on the door. If required, adjust the spring tension
REFERENCE LABEL ON CLOSER FOR MINIMUM/MAXIMUM SETTINGS
BARRIER-FREE OPENINGS -
+
-
+12
200 5
WEIGHT (LBS)
CLOSER
TS93-1
TYPE
100
150
125
DOOR
4'
3'6"
3'
2'6"
3'6"
MAX.
3'
2'6"
---
SPRING
ADJUSTER
OF SPRING
2
4
3
SIZE
0
+9
+3
FULL TURNS
+12
+3
+9
0
5
3
4
2
SPRING ADJUSTER
FULL TURNS OF
INT.
DOOR WIDTH
EXT. CLOSER
SIZE
M5 HEX KEY
NOTE:
TS93-5 supplied with a size 6 spring setting.
NOTE:
Maximum number of turns clockwise = 6
TS93-1
0
SPRING ADJUSTER
FULL TURNS OF
4'
4' 6"
TS93-5 DOOR WIDTH
EXT.
3' 6"
INT.
4' -4 6
CLOSER
SIZE
5
0
-4
5
6
200
250
TS93-5
08280611 3 of 3 08/09
INS NO. PAGE Rev.
screw.
Secure with locking
TAB
COVER
cover onto plate.end caps.
Slide end covers over closer body
REMOVE
Remove tab that aligns with arm hub. Slide
Install cover.
9