Dräger Fabius GS SW 1.3n Specifications

Breathing system heater
Fabius®GS SW 1.3n (90 37 781)
Fabius®GS SW 2.n (90 37 933)
Fabius®GS SW 3.n (90 38 685)
Fabius®Tiro SW 2.n (90 38 132)
Fabius®Tiro SW 3.n (90 38 686)
Fabius®GS premium SW 3.n (90 38 923)
Fabius®plus SW 3.n (90 39 054)
Supplement to Operator’s Instruction Manuals

Contents
2Fabius GS/Tiro Supplement
Contents
For Your Safety and that of Your Patients .................................................................. 3
Purpose of This Document ........................................................................................ 4
Breathing System Heater (Optional) ....................................................................... 4
Symbol Definition ....................................................................................................... 5
General Warnings and Cautions ................................................................................ 6
Installation of BSHPS (Fabius GS) ............................................................................ 7
Installation of BSHPS (Fabius Tiro) ........................................................................... 9
Operation of BSHPS ................................................................................................ 14
Switching Off BSHPS ............................................................................................... 16
Preparing the Compact Breathing System for Disinfection and Cleaning ................ 16
BSHPS Technical Data ............................................................................................ 18
Daily Checkout ......................................................................................................... 19

For Your Safety and that of Your Patients
Fabius GS/Tiro Supplement 3
For Your Safety and that of Your
Patients
Strictly follow the Instructions for Use
Any use of the breathing system heater requires full
understanding and strict observation of these
instructions and the Fabius GS or Fabius Tiro
Operator's Instruction Manual. The apparatus is only
to be used for purposes specified here.
Safe connection with other electrical equipment
Electrical connections to equipment which is not
listed in these Instructions for Use should only be
made following consultations with the respective
manufacturers or an expert.
Not for use in areas of explosion hazard
This apparatus is neither approved nor certified for
use in areas where combustible or explosive gas
mixtures are likely to occur.
Liability for proper function or damage
The liability for the proper function of the apparatus is
irrevocably transferred to the owner or operator to
the extent that the apparatus is serviced or repaired
by personnel not employed or authorized by
DrägerService or if the apparatus is used in a
manner not conforming to its intended use.
Dräger cannot be held responsible for damage
caused by non-compliance with the
recommendations given above. The warranty and
liability provisions of the terms of sale and delivery of
are likewise not modified by the recommendations
given above.
Dräger Medical GmbH

Purpose of This Document
4Fabius GS/Tiro Supplement
Purpose of This Document
Breathing System Heater (Optional)
Breathing system heater for use in conjunction with
the Fabius GS and Fabius Tiro anaesthetic machines
in order to reduce the condensation of moisture in
the breathing system during low-flow operation (fresh
gas flow below 1 l/min).
This Instruction Manual supplement contains
additions to the information contained in the Fabius
GS or Fabius Tiro Operator's Instruction Manual.

Symbol Definition
Fabius GS/Tiro Supplement 5
Symbol Definition
The following symbols appear on the power supply of
the (optional) breathing system heater.
Caution: Refer to accompanying documents
before operating equipment.
Caution: Risk of electric shock, do not remove
cover. Refer servicing to a
DrägerService representative.
Degree of protection against electric shock:
Class 1 Type B.
Registration Mark
Mains Applied/Mains Power
Fuse
Heater Power
DC Voltage
AC Voltage
!
CUS

General Warnings and Cautions
6Fabius GS/Tiro Supplement
General Warnings and Cautions
The following list of warnings and cautions apply to
general operation and maintenance of the Fabius GS
and Fabius Tiro. Warnings and cautions about
installing and operating specific parts appear with
those topics.
• A Warning statement gives important
information that, if ignored, could lead directly
to personal injury.
• A Caution statement gives important
information that, if ignored, could lead directly
to equipment damage and indirectly to
personal injury.
Warning: When the moisture content falls below a
specified minimum level, the following
undesirable reactions can occur,
regardless of the type of CO2absorbent
and the anaesthetic agent used, e.g.
Halothane, Enflurane, Isoflurane,
Sevoflurane or Desflurane:
• reduced CO2absorption,
• formation of CO,
• absorption and/or decomposition of
the inhalation anaesthetic agent,
• increased heat generation in the
absorber, leading to higher breathing
gas temperatures.
Additionally, the breakdown products of
anaesthetic agents exposed to dry
absorbent are both flammable and toxic,
and fires have been reported in
association with the use of desiccated
absorbent and volatile anaesthetics.
These reactions can result in danger to
the patient in the form of CO intoxication,
insufficient depth of anesthesia and
airway burns.

Installation of BSHPS (Fabius GS)
Fabius GS/Tiro Supplement 7
Installation of BSHPS (Fabius GS)
The following provides instruction on installation of
the power supply for the breathing system heater
(mains adapter).
Figure 1. BSHPS Installation on Machine with Left Mount
COSY
Left Mount COSY BSHPS Installation
The following numbers in boldface refer to Figure 1.
1. Install the power supply onto the left rear GCX
rail of the Fabius GS by sliding the mounting
plate of the power supply through the opening of
the rail (1) and then sliding it upward. Tighten the
knob (2) against the rail when the power supply
is in the desired position.
2. Route the power cable (3) for the heater below
and behind the power supply and then up to the
rear of the COSY arm. Push the cable into the
cable management cavity (4) on the bottom of
the COSY arm.
3. Plug the connector at the end of the cable into
the mating connector (5) on the rear underside of
the COSY. Orient the connector so that the red
mark on the connector plug aligns with the red
mark on the receptacle.
1
2
3
45

Installation of BSHPS (Fabius GS)
8Fabius GS/Tiro Supplement
Figure 2. BSHPS Installation on Machine with Right Mount
COSY - Step 1
Right Mount COSY BSHPS Installation
1. Install the power supply onto the left rear GCX
rail of the Fabius GS by sliding the mounting
plate of the power supply through the opening of
the rail (1in Figure 1) and then sliding it upward.
Tighten the knob (1in Figure 2) against the rail
when the power supply is in the desired position.
2. Route the power cable for the heater through the
trough (2in Figure 2) on the rear of the cabinet.
At the right hand end of the trough, route the
cable into the cable management cavity
(1in Figure 3) on the bottom of the COSY arm.
Figure 3. BSHPS Installation on Machine with Right Mount
COSY - Step 2
3. Plug the connector at the end of the cable into
the mating connector (2in Figure 3) on the rear
underside of the COSY. Orient the connector so
that the red mark on the connector plug aligns
with the red mark on the receptacle.
1
2
1
2

Installation of BSHPS (Fabius Tiro)
Fabius GS/Tiro Supplement 9
Installation of BSHPS (Fabius Tiro)
The following provides instruction on installation of
the Breathing System Heater Power Supply
(BSHPS).
Figure 4. BSHPS Installation on Machine with Left Mount
COSY (Trolley)
Left Mount COSY BSHPS Installation
(Trolley)
The following numbers in boldface refer to Figure 4.
1. Install the power supply onto the left rear GCX
rail of the Fabius Tiro by sliding the mounting
plate of the power supply through the opening of
the rail (1) and then sliding it upward. Tighten the
knob (2) against the rail when the power supply
is in the desired position.
2. Route the power cable (3) for the heater below
and behind the power supply and then up to the
rear of the COSY arm. Push the cable into the
cable management cavity (4) on the bottom of
the COSY arm.
3. Plug the connector at the end of the cable into
the mating connector (5) on the rear underside of
the COSY. Orient the connector so that the red
mark on the connector plug aligns with the red
mark on the receptacle.
1
2
3
45

Installation of BSHPS (Fabius Tiro)
10 Fabius GS/Tiro Supplement
Figure 5. BSHPS Installation on Machine with Right Mount
COSY - Step 1 (Trolley)
Right Mount COSY BSHPS Installation
(Trolley)
1. Install the power supply onto the left rear GCX
rail of the Fabius Tiro by sliding the mounting
plate of the power supply through the opening of
the rail (1in Figure 4) and then sliding it upward.
Tighten the knob (1in Figure 5) against the rail
when the power supply is in the desired position.
2. Route the power cable for the heater through the
trough (2in Figure 5) on the rear of the cabinet.
At the right hand end of the trough, route the
cable into the cable management cavity
(1in Figure 6) on the bottom of the COSY arm.
Figure 6. BSHPS Installation on Machine with Right Mount
COSY - Step 2 (Trolley)
3. Plug the connector at the end of the cable into
the mating connector (2in Figure 6) on the rear
underside of the COSY. Orient the connector so
that the red mark on the connector plug aligns
with the red mark on the receptacle.
1
2
1
2