Installation/Operating Instructions
220V Artisan Series Electric Projection Screen
These Installation/Operating Instructions are available in the official language
of the country where you purchase the product. Please contact your distributor
to request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez demander
à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen
Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen
Sie die jeweilige Verkaufs-Abteilung.
Caution
➀
Read instructions through completely before proceeding.
➁
Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂
Screen should be accessible for complete removal should fabric
become damaged or should other service be required.
➃
Screen should be installed level (using a carpenter’s level).
➄
Nothing should be fastened to screen dowel or viewing surface.
➅
Operating switch(es) packed separately in screen carton. Do not
discard with packing material.
➆
Screen operates on 220 v., 50 Hz., 1 ph. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
General
When locating viewing surface and checking clearance for screen’s operation,
remember surface is centered in case. Take care to install wall/ceiling electrical
box and conduit so they will be fully concealed by the screen case after instal-
lation.Handle case carefully to protect its finish.Regardless of mounting method,
screen should be positively and securely supported so that vibration or even
abusive pulling on the viewing surface will not cause case to work loose or fall.
Installer must insure that fasteners used are of adequate strength and suitable
for the mounting surface chosen.
Wall Mounting
Mount 2, 3, or 4 aluminum brackets provided on the wall at desired height, us-
ing toggle bolts provided or other appropriate fasteners. Verify that they are in
line and level to fully engage matching brackets pre-installed on back of screen
case. When screen is set on brackets, pull down gently to ensure that it is snug
and secure.
Ceiling Mounting
Install through the two 24 mm diameter mounting holes at each end of the screen
case, using appropriate fasteners.
Copyright ©2003 Draper Inc. Form ArtisanE&V220V_Inst03 Printed in U.S.A.
If you encounter any difficulties installing or servicing your Artisan
Series screen, call your dealer or Draper, Inc. Spiceland, Indiana,
U.S.A., telephone (765) 987-7999, fax (765) 987-1689, or email
Electrical Connections
Screen operates on 220 v., 50 Hz., 1 ph. current. Junction box is located inside
left endcap and cover plate is secured to endcap with two screws. Junction box
contains terminal strip, per wiring diagram on reverse.
Wall or ceiling electrical box should be installed so as to be fully concealed by
screen case after installation. Conduit openings are covered by plastic caps (to
be removed for installation). Opening for ceiling mounting is located in top, 73
mm from the end and 64 mm from the back of the case. Opening for wall mount-
ing is in back, 73 mm from the end and 70 mm from the top of the case.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire connecting screen to switch(es) and switch(es) to power supply
should be furnished by installer. Connections should be made in accordance
with wiring diagram supplied, and wiring should comply with national and local
electrical codes.
All operating switches should be “Off” before power is connected.
Operation
Series E: Before operating screen remove tape securing fabric and dowel to
roller. If viewing surface hangs out of case 20 to 23 cm, tape has probably been
broken by rough handling in shipment, allowing surface to “unwrap” one turn
about the roller. Manually wrap the fabric back around the roller without turning
the roller itself.
Series V: Important Instructions—The shipping support brackets must be re-
moved from each end of dowel during initial operation before screen is operated
in UP direction. After screen is installed, run viewing surface DOWN to access
screws that hold brackets to dowel. Loosen hex head screw, remove bracket and
retighten screw at each end of dowel. Cycle viewing surface down and up sev-
eral times to confirm satisfactory operation. If viewing surface does not operate
properly, turn power off and check electrical connections.
220V Single Station Control—3-position up-off-down switch permits operation
to be stopped at any point. Factory adjusted limit switches automatically stop
screen when fully down or fully up.
220V Multiple Station Control (Not CE approved)—Switches are similar in ap-
pearance to 220V Single Station Control. Screen stops when switch is released
and may be restarted in either direction. Factory adjusted limit switches stop
screen automatically when fully up or fully down.
24V Control—Three-button up-stop-down switch(es) stop at any point desired,
operate in any sequence. Factory adjusted limit switches automatically stop
screen when fully up or fully down. Installer should incorporate an all-pole dis-
connect in the fixed wiring.
Key Operated Switching (Not CE approved)—Two kinds of key-operated
switches are optionally available with this unit.
➀
The key-operated power sup-
ply switch controls power to the screen and switches. When it is “off”, the switch-
es will not operate screen. Key may be removed from the switch in either “on” or
“off” position.
➁
A three-position key switch permits the screen to be operated
directly by key. In this case, the screen’s operator must always have a key.
Adjustments
Screen has been factory set and should not normally require further adjustment.
However, if you desire to change the “up” and “down” stopping positions, proceed
as follows:
CAUTION: Be sure all switches are in “off” position before adjusting limit
switches. Always be prepared to shut screen off manually when new adjustment
is being tested. Screen may be severely damaged if viewing surface is allowed to
run too far up or too far down.
Adjusting “fully up” position — “Up” stopping position may be adjusted by
turning the yellow limit switch adjustment socket. The yellow socket is located on
left end of screen roller and is accessible to a screwdriver/Allen wrench (4mm or
5/32"). Turning the socket counterclockwise will allow the viewing surface to retract
farther into the case. Turning it clockwise will cause the surface to stop farther
out of the case. One full revolution of the socket will alter the stopping position of
the viewing surface by approximately 38 mm (1½").
Adjusting “fully down” position — “Down” stopping position may be adjusted
by turning the white limit switch adjustment socket. The white socket is located
on the left end of screen roller and is accessible to a screwdriver/Allen wrench
(4mm or 5/32"). Turning the socket counterclockwise will allow the viewing surface
to run farther down. Turning it clockwise will shorten the viewing surface, caus-
ing it to stop in a less extended position. At no time should viewing surface be
unrolled enough to expose any part of screen roller.
Z-brackets supplied
with screen for
wall mounting.
Hardware by others.
Z-brackets on
rear of case
Screen Case
Knockout for rear
conduit connection
Left end
24 mm holes for
ceiling mounting.
2 each end.
Ceiling mounting hardware
b
others
Wall
Knockout for top
conduit connection
