DREAMS Jay User manual

IMPORTANT OTTOMAN SAFETY WARNINGS
IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE
You must ensure that the mattress is on the bed frame before operating the
lift mechanism – Failure to do so could result in injury.
Keep hands clear of the mechanism when opening or closing the ottoman.
Beware of entrapment – Never reach in through the mechanism to access
the storage area.
Always ensure that the ottoman is FULLY opened before accessing the
storage area.
Do not exceed the maximum weight as specified in the table below:
Two person
assembly
1.5 hour approx
assembly time
Jay Ottoman Bed
MK1 230329
with O.S.B.
WARNING!HAZARD - DO NOT REACH INTO THE SPACEB ELOW!
Bed Min Weight (kg) Max Weight (kg)Bed Size
Double 10 40
King
Super King
15
20
45
50
Jay
Mattress Base Board

Don’t lift without mattress Ensure mattress is on before lifting
•Use caution when operating, always use the handle when lifting.
•Note: This bed uses a pressurised mechanism.
•To be operated by adults only.
•Please ensure that children and pets are kept away from the bed when
operating the lift mechanism.
•Keep children and pets away from the storage area.
•Do not overload the internal storage base.
•Do not stand inside the internal storage area of the bed.
•Before removing the mattress secure the frame to ensure it does not open
unexpectedly.
•Do not attempt to lie on the mattress when the ottoman is in the raised
position.
•When lifting the ottoman, remove all bedding except the fitted sheet.
IMPORTANT OTTOMAN SAFETY WARNINGS Cont.
WARNING!HAZARD- DO NOT REACH INTO THE SPACEBELOW!
WARNING!HAZARD- DO NOT REACH INTO THE SPACEBELOW!
Jay Ottoman Bed - Assembly guide - Page 2
WARNING! HAZARD - DO NOT REACH INTO THE SPACE BELOW!
Note: Be very careful what you
store under the bed -the top of
an item, like a suitcase or a box
must not touch the slats or they
may be damaged. Maximum
storage height is 315mm .
WARNING!HAZARD - DO NOT REACH INTO THE SPACE BELOW!
WARNING
TO AVOID ACCIDENTS
To access the storage area, the ottoman frame
MUST BE FULLY OPENED and then
FULLY CLOSED afterwards.
CAUTION
To be operated by ADULTS ONLY.
Keep children and pets away from the storage area.
Avoid trapping your fingers by using the handle
to lift & lower the base.
Only lift when the mattress is in place.
Ensure the ottoman support bar is secure when the
base is open.
Regularty air internal storage area and contents.
!

Read all the instructions before using your Ottoman bed-frame and save the instruction booklet for future reference.
Ottoman Support Bar (O.S.B.)
For optimal safety during operation, always ensure the O.S.B. is engaged when accessing the
ottoman storage area.
Ottoman Beds - Important Safety Features
1 . Always raise the ottoman slat-frame to it's highest position before using the storage area.
Locate the end of the O.S.B and insert into the fixed retaining bracket on the bed frame.
2 . When you are ready to lower the ottoman platform, return the O.S.B to its original parking position.
3 . Always ensure that the O.S.B is in position when the ottoman is open, this prevents injury, or
damage to the product.
Location of the O.S.B
End-lift
:
O.S.B is on
the left
side of
the bed.
Side-lift: O.S.B is on either
the left side or right side of
the footend.
WARNING! Risk of Entrapment
oThe pistons on the ottoman bed frame can support a maximum load (evenly spread) as indicated in
the Minimum and Maximum load table, on Page 1 of this Assembly Instruction.
oOverloading the sleeping platform may contribute to damage to the product resulting in potential
serious injury.
oDo not sit on the mattress whilst the platform is in motion or is in the raised position.
oUsers should only get in and out of bed when platform is in the flat (horizontal) position.
WARNING! HAZARD-DO NOT REACH INTO THE SPACE BELOW!
!
your comfort and safety. Please take time to look at these instruction as they will help remind you how to
operate your ottoman bed safely.
Here’s a few things you need to remember;
Pistons are already assembled in their correct orientation – this improves piston performance and
durability.
“Break in ” the piston seals on first use by raising & lowering the platform at least five times.
Recommended mattress weights - do not exceed the maximum relevant weight specified on the
Assembly Instruction.
Ottoman support bar – always engage the support bar when accessing the ottoman storage area.
Jay Ottoman Bed - Assembly guide - Page 3
L.
R.

Jay Ottoman Bed - Assembly guide - Page 4
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your bed.
We advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
Help and support
At Dreams, it’s our mission to give the whole nation a great night’s sleep - this
means that the quality of our products is of utmost importance to us. If there
are any issues with your product or any missing parts, please contact our Help
Centre on 0800 652 6750, where a member of our team will be happy to help.
(For customers based in Northern Ireland, please call 028 9050 8300)
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this bed which could
present a choking hazard. All plastic and wrapping materials should also be
To keep your little ones busy, there is a colouring page inside the back cover.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.
We recommend that you build your new bed in the room you’d like it to be
located - this will help prevent any risk of damage to your newly built bed
whilst moving it.
Top tip
Thank You
Dear Customer, Thank you for choosing to purchase your bed from Dreams - we hope it brings you
your best ever night’s sleep. Before you begin building your bed, please take a moment to read
through the instructions and make sure that you've got all the relevant parts listed on the following
pages.

Jay Ottoman Bed - Assembly guide - Page 5
Parts
Important information
The bed you have purchased comes with solid mattress base boards, please follow the instructions
below in the current order. Before you begin building your bed, please take a moment to read through
the instructions and make sure that you've got all the relevant parts listed on the following pages.
0 1 2 3 4 5 6 7 8 9 1010 11 12 13 14 15 16 17 18
cm
1
1
1
1
1/2
A. Headboard
B.
C.
D.
E.
F. 2
1
1
1
4
2
2
2
4
2
3B
2
2
G.
N.
1
1
3B
3B
3B
1 3B
1
1 3B
ytQ xoBCode Description ytQ xoBCode Description
Parts list
Footboard
Side Rail - Left
Side Rail - Right
Support Brackets
Double & King/Super King
Angled Corner Brackets
Side Rail Cross Bar
Fabric Hand Strap
1X. 3BMattress Base Board - Footend
R. Met al Plate for Fabric Hand Strap
S. Gas Lift Pistons
T. Mattress Stoppers
U. Support Rail for Mattress Base Board
H. Fabric Base Cover
W. Mattress Base Board - Headend
2
2
2
1
1
Ottoman support bar PACK (O.S.B.)
Ottoman support bar
Fixed retaining bracket - side rail
Parking bracket - slat-frame
O.
P.
Q. 1
A
B
C
D
T
E
F
F
S
S
G
N
O
PQ
R
H
W
X
U

Jay Ottoman Bed - Assembly guide - Page 6
Cross head screwdriverTape measure
Tools required
m x5
b x5 c x5
Bolts (M8x25mm) for fitting
ottoman support bar
Flat washer for M8 bolts
O x1
Q x1
P x1
Spring washer for M8 bolts
Hardware needed for fixing ottoman support bar (O.S.B) to the slat frame
packed in the side rail carton, inside Pack 2 - hardware pack (C)
Ottoman Support Bar
Fixed retaining bracket
- side rail Parking bracket - slat frame
Spring Washer for M8 bolt Flat Washer for M8 bolt
h x4 i x8
q x1
Flanged lock-nuts M8
for gas-lift pistons Nuts for M8 bolts
Tube spanner for M8 nut
n x2
b x16 c x16 k x6
Big Head Bolts (M8x20mm) for
fitting metal plate (R) and
mattress base boards (W&X)
mattress stoppers (T) to
r x8
Metal connection plate for
mattress base boards (W&X)
l x8
Bolts (M8x30mm)
Fitting mattress base boards
to gas-lift mechanisms Threaded stud (M8x50mm)
Fittings
Please check you have all the fittings listed below with your product:
Hardware needed for fixing side rails to headboard & footboard
Packed in side rail carton, inside Pack 2 - hardware pack (A)
Hardware needed for fixing mattress base board
Packed in mattress base board carton, inside Pack 3B - hardware pack (D)
Spring Washer for M8 bolt
a
Flat Washer for M8 bolt
b c
d x1
Allen Key for M8 bolt
Bolts (M8x25mm)
Fitting side rails (C&D) to
headboard & footboard (A&B)
e
Bolts (M8x50mm)
Fitting Support block (p)
to side rail cross bar (G)
Double & King x28
Super King x30
Double & King x26
Double & King x1
Super King x2
Double & King x1
Super King x2
Double & King x29
Super King x32
p
Support block
for side rail
cross bar (G).

Please do not tighten 100% yet.
Jay Ottoman Bed - Assembly guide - Page 7
a
x6
b
x6
c
x6
d
x1
a
Double & King x1
Super King x2
2
Prepare headboard & footboard
for assembly.
b
x8
x1
1
10mm
a
c
b
E
B
B
A
A
a x2
c x2
x10
x12
Double & King
Super King
x10
x12
Double & King
Super King
d
c
10mm
a
c
b
Fit both side rails to headboard & footboard, tighten all bolts 90%.
90%
a
cb
d
A
C
&
D
A
B
C
DB
a
cb
d
C
&
D
90%

Jay Ottoman Bed - Assembly guide - Page 8
a
x8
b
x8 c
x8
d
x1
3Fit the angled corner brackets and tighten all bolt sets 90%.
a
c
d
b
F
C
D
&B
Make certain the bed is squared up as shown in the diagram then tighten all bed assembly bolts 100%.
Slat Frame Support Bar
h
q
hx2 q x1
WARNING!HA ZARD - DO N OT REACH INTO THE SPACE B ELOW!
Fit the piston stems to upper axles
using lock nuts (h) - do not tighten yet.
J
J
J
4 Loosely fit the piston stems to the upper axles.
Please make sure the cylinder
(largest diameter) is at the top.

Jay Ottoman Bed - Assembly guide - Page 9
5
6
r
x4
d
x1
n
x2
n
X
X
r
l
x4
b
x4
c
x4
l x2
c x2
b x2
CAUTION
Tobe operated by
ADULTSONLY
.
Keep children and pets away from the storage area.
Avoidtrapping your fingers by using the handle
tolift & lower the base.
Only lift when the mattress is in place.
Ensurethe ottoman support bar is secure when the
baseis open.
Regularlyair the internal storage area and contents.
WARNING
TO AVOID ACCIDENTS
Toaccess the storage area, the ottoman frame
MUST BE FULLY OPENED
and then
FULLY CLOSED afterwards.
!
Prepare the upper mattress base board (X).
90%
100%
q
x1
i
x4
b
x4
c
x4
X
c
b
i
q
TO THE SPACE BELOW!
Lay the base board
onto the support bars
carefully sliding the
studs through the
upper holes. Using
two nut sets on each
side (i, b & c),
connect the threaded
studs loosely to the
bars. Please do not
tighten 100% yet.
Fit the first base board (X) at the top of the support arms.
Fit four studs (r)
as shown
Fit the two metal connection
plates (n) to the edge of the board
(X) using bolt sets (I, b & c).
Please do not tighten yet.

Jay Ottoman Bed - Assembly guide - Page 10
7
8
r
x4
W
W
r
x4
100%
180°
q
x1
i
x4
b
x4
c
x4
k
x4
d
x1
x2
k x2
W
T
W
WARNING! HAZARD - DO NOT REACH IN
U
Bolt into centre
of LONG holes
c
b
q
i
To the first lower holes in the support bars (next to the headboard)
fit the support rail (U) to the mattress base board (W) using two
nut sets, (i, b & c), one set at each end.
Using one more nut set on each side (i, b & c), fix the second pair
of studs loosely to the support bars.
Please do not tighten 100% yet.
100%
Fit the second base board (W).
Fit the mattress stoppers
(T) to the edge of the
board using the large
head bolts (K).
Turn over and fit four
studs (r) to the base
board (W) as shown
X
W

Jay Ottoman Bed - Assembly guide - Page 11
9
10
W
W
X
X
d
x1
l
x4
b
x4
c
x4
Make sure the mattress base boards are aligned at each side
and pushed close together in the middle, then tighten all
eight bolt sets (I, b & c) 100% using Allen key (d).
Using two bolt sets (l, b & c), loosely screw
through each metal connection plate (n) into
the mattress base board (W).
ii)
x2
l x2
c x2
b x2
Make sure the bed is still square and there
is an even gap all round as in the sketch.
8 mm
Finally, on the support bar studs, tighten all eight nut sets 100% using tube spanner (q).
q
x1
i)
W
X

12
k
x2
d
x1
i)
ii)
k x2
X
R
H
Jay Ottoman Bed - Assembly guide - Page 12
11
2mm
h
x2
q
h
Fit the lower piston stems to the axles and fit the lock-nuts (h).
Tighten them with tube spanner (q) but note, a small 2mm gap is
needed so stems can move freely - this is important so do not
over-tighten - see sketch -->
q
x1
Fit the fabric hand strap as shown.

Jay Ottoman Bed - Assembly guide - Page 13
1
c
m
b
c
m
b
P
O
Q
b
x5
c
x5
d
x1
m
x5
The bolts should be in the centre of the
long holes and one may need to slide
the inner bar and the bracket, up or
down so the bottom of the O.S.B stem
just touches the surface - better to do
this AFTER the mattress is fitted.
90%
ii)
To underneath of the mattress base board, fit the parking
bracket (Q). This is used to safely keep the support
bar out of the way when not in use. Use one bolt set
(m, b & c) - please make sure the bracket is fitted
the correct way round as shown. Screw into the
threaded insert on the underside of the frame.
i)
iii)
100%
100%
To underneath of mattress base board, fit
the O.S.B. support bar (O) as shown.
Using two bolt sets (m, b & c), screw
the bolts into into the threaded inserts
on the underside of the frame.
Please do tighten 100% yet.
Fit the fixed retaining bracket
(P) to the side rail using two
bolt sets (m, b, & c). Screw the
bolts into the threaded inserts
on the side rail. Make certain
the bracket is level and at the
correct height.
Please do not tighten 100% yet.
Unpack the contents of the Ottoman Support Bar (O.S.B.)
from it's carton - this is packed inside Pack 2.
iv)
WARNING! HAZARD DO NOT REACH INTO THE SPACE BELOW!
c x2
m x2
b x2

Jay Ottoman Bed - Assembly guide - Page 14
14
100%
Parking position
Setting the inner stem of the support bar (O), adjust the inner stem
to the correct length.
Set the inner stem to the correct length so the end just touches
the retaining bracket - it needs to touch to hold it in position.
Adjust the retaining bracket (P) so
the stem end scrapes the surface.
WARNING! HAZARD DO NOT REACH INTO THE SPACE BELOW!

Jay Ottoman Bed - Assembly guide - Page 15
H
15
16
b
x4
c
x5
d
x1
e
Double & King x1
Super King x2
Double & King x1
Super King x2
p
a
x4
ii)
Using four bolt sets (a, b & c) fit the
cross bar (G) to both side rails (C&D).
Tighten 100% using Allen key (d).
Take care not to damage the fabric
when fitting.
i) Fit the support block (p) in the centre of the side
rail cross bar (G) using a bolt & flat washer (e & c).
(N.B. there are two blocks on the Super King size)
Tighten 100% using Allen key (d).
G
a x2
e
c
p
c x2
b x2
G
G
WARNING!HA ZARD - DO N OT REACH INTO THE SPACE B ELOW!
WARNING!HAZARD - DO NOT REACH INTO THE SPACEBELOW!
Fit the fabric base cover (H) evenly around the inside of the bed.

Jay Ottoman Bed - Assembly guide - Page 16
Care and maintenance
Here are some tips to keep your new bed in tip-top condition
Cleaning
To clean your new bed, we'd advise using a warm damp cloth or if fabric, remove
dust using a low suction vacuum cleaner.
Please do not use abrasive chemicals or bleach as this may damage the product.
Checking and moving
Periodically we recommend you check that the screws or fixtures haven't become
loose over time. To move your new bed, we recommend lifting it where possible, as
dragging or pushing it could cause damage to the legs or flooring.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Fabric
Please note depending on the lighting, positioning and surroundings of your
period of time, the colour might lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. We recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Thank you for shopping with us - we hope you have a
great night's sleep.
80
W
H
L
355
Floor to top
of the mattress
board
30
Top of board to
top of side rail
Technical Specifications
Overall Dimensions (LWH mm)
Double:
King:
Super King:
Internal Dimensions (LWH mm)
Ottoman Piston Rating
Double: 900 N
King: 1000 N
Super King: 1200 N
2150 x 1940 x 1220
2150 x 1640 x 1220
2050 x 1490 x 1220
Double:
King:
Super King:
2050 x 1830 x 315
2050 x 1530 x 315
1950 x 1380 x 315
35
10
35
385

Little dreamers
Keep the little ones entertained while
you assemble your new purchase.