DREAMS Jade Single Bunk User manual

Jade Single Bunk
Assembly Instructions
Need assistance?
Call: 0344 292 0000
Dimensions mm Length Width Height
Single 2010 1000 1600
Approximate time to
assemble this product
Retain these instructions
for future reference
2 x people recommended to
assemble this product
Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fixings.
You will require a cross
head screwdriver
Helpful advise before you begin:
1. We suggest you spend a short time reading through this leaflet
and then follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be
worth the effort.
3. Do not discard any of the packaging until you have checked that
you have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings
are only finger tightened during initial assembly. Only upon
completion of the assembly should all fixing points be fully
tightened.
6. We recommend a periodic check on all fixing points to make
sure they remain fully tightened.
7. Keep glue and fittings out of children’s reach.
8. Do not use any other tools other than those recommended to
build this product.
9. Please do not use substitute parts. Use only additional or
replacement parts supplied by Dreams Ltd.
10. In the unlikely event that this product has missing or damaged
parts, please call 0344 292 0000 to obtain spares.
Page 1 of 13
1

Page 2 of 13
Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fixings.
Fittings Checklist
Parts Checklist
Ø6 x 65mm Bolt
x 7
Check size of fixings against this guage (dimensions in mm)
10 20 30 40 50 60 70 80 90 100 110
A
Top Bed Legs 2pcs
Top Bed Legs x2pcs
02
Base Head Frames x4pcs
01
03 Connect Round
Tubes x4pcs
04
Base Legs x2pcs
05
Base Legs x2pcs
Side Rail x4pcs
06
07
Bed Connectors x4pcs
08
Bed Connectors x4pcs
09
Inside Frame
Protect Frame
10
11
Ladder
12
Ø6 x 45mm Bolt
x 3
B
Ø6 x 20mm Bolt
x 56
C
Washer
x 27
D
M6x18 Nuts
x 3
E
Caps Dia 10mm
x 28
H
Caps Dia 50mm
x 8
F
Allen Key M4
x 2
G
Round Tube
x 80
I
01
01
01
01
03
03
04
04
04
05
05
06
06
07
07
07
07
08
08
08
08
10
04
09
09
09
09
11
12
02
02

Page 3 of 13
Bed Frame Assembly
1 x2
x 8
Washer
D
x 8
Ø6 x 20mm Bolt
C
x 1
Allen Key M4
G
x 8
Washer
D
x 8
Ø6 x 20mm Bolt
C
05
06
2 x2
DG
01
01
DG
03
C
C
02

Page 4 of 13
Bed Frame Assembly
3
4
x 4
Ø6 x 20mm Bolt
C
x 4
Ø6 x 20mm Bolt
C
C
G
C
G
01
01
03
03
02
02
Note: Leave 10 mm
protruding as in the
diagram.
Note: Leave 10 mm
protruding as in the
diagram.
05
05
05
06
06
02
10mm
10mm

x 80
Round Tube
I
08
08
09
09
Page 5 of 13
Bed Frame Assembly
5 x2
6 x2
x 16
Ø6 x 20mm Bolt
C
08
08
09
09
07
I
I
C
C
G
G
07
08
08
08
08
09
09
07
90%
Loosely tighten
the Bolts

Page 6 of 13
Bed Frame Assembly
7
8
07
07
07
07
07
07
02
02
02
03
03
05
05
05
06
06

x 4
Ø6 x 20mm Bolt
C
x 4
Ø6 x 20mm Bolt
C
Page 7 of 13
Bed Frame Assembly
9
10
C
G
C
G
07
07
07
07
07
07
02
02
02
03
03
05
05
05
06
06
C
C
90%
Loosely tighten
the Bolts
90%
Loosely tighten
the Bolts

Page 8 of 13
Bed Frame Assembly
11
12
x 8
Ø6 x 20mm Bolt
C
x 2
Washer
D
x 4
Ø6 x 65mm Bolt
A
02
02
03
03
04
04
04
04
05 05
06
06
C
C
D
D
D
AG
10
10
07
02
02
A
G
03
03
03
x 8
Washer
D
04
05 G
02
04
90%
Loosely tighten
the Bolts

Page 9 of 13
Bed Frame Assembly
13 a
13 b
x 1
x 2
Washer
D
x 3
Ø6 x 65mm Bolt
A
x 3
M6x18 Nuts
E
x 3
Ø6 x 45mm Bolt
B
A
G
B
E
G
G
AD
12
07
11
03
Option: 01
The ladder on the
right side.
Choose which side of
ladder you want to fit
Option: 01
The ladder on the
right side.
07 12
11
07
03
90%
Loosely tighten
the Bolts
Fully tighten all bolts
and screws at this step

DAG
02
A
G
Page 10 of 13
14 a
14 b
x 1
Washer
D
x 3
Ø6 x 65mm Bolt
A
x 3
M6x18 Nuts
E
x 3
Ø6 x 45mm Bolt
B
B
G
G
E
12
07
11
11
07
Bed Frame Assembly
03
02
Option: 02
The ladder on the
left side.
Option: 02
The ladder on the
left side.
07
12
03
90%
Loosely tighten
the Bolts
Fully tighten all bolts
and screws at this step

Cap Holes
15
x 28
Caps Dia 10mm
H
x 8
Caps Dia 50mm
F
Page 11 of 13
The bed can be seperated
into two single beds.
F
F
F
F
F
F
F
H
H
HHH
HH
H

Finished Assembly
16
Page 12 of 13
Important Note:
Before you use the unit, Please
choose the right
mattress on it.
The maximum
thickness of the
mattress must under the level
of the mark.
Note:
• Do not stand on the bed before placing the mattress.
• Assemble on a smooth flat surface.
• The recommended size of the mattress is 90x190cm, the mattress thickness should not exceed 17cm.
• Here state that ventilation of the room is necessary in order to keep the humidity low and to prevent mould in and around the
bed.
• This product complies with European Standard BS EN 747-1:2012+A1:2015 & 747-2:2012 + A1:2015
• WARNING: High beds and the upper bed of bunk beds are not suitable for children under six years due to the risk of injury from
falls.
• WARNING: Bunk beds and high beds can present a serious risk of injury from strangulation if not used correctly.
Never attach or hang items to any part of the bunk bed that are not designed to be used with the bed, for example, but not
limited to ropes, strings, cords, hooks, belts and bags.
• WARNING: Children can become trapped between the bed and the wall, a roof pitch, the ceiling, adjoining pieces of furniture
(e.g. cupboards) and the like. To avoid risk of serious injury the distance between the top safety barrier and the adjoining
structure shall not exceed 75mm or shall be more than 230 mm.
• WARNING: Do not use the bunk bed/high bed if any structural part is broken or missing.

Page 13 of 13
Care of your Dreams Furniture
Your new bed from Dreams is more than a beautiful piece of
furniture. It’s an investment in your health and wellbeing. Care
for it well and you’ll enjoy a great night’s sleep for many years
to come.
Should you have any issues with your product please contact
our customer service team on 0344 292 0000
On Delivery
Once your new bed is in place and all the packaging is removed,
let it air for approximately 1 hour before putting on your mattress,
mattress protector and bed linen.
Don’t worry if your bed feels a little strange at first. It takes time
for your body to adjust to a new level of support and comfort. You’ll
soon be enjoying a more relaxed sleep.
Please consider the surface your bed will be stood on. If your bed
frame is to be stood on an uncarpeted surface please ensure that
you use rubber backed mat under the legs to avoid slipping.
Day to day Care
Please use only 5% soap, 95% water solution, wiping with a damp
cloth. Finally dry with a soft clean cloth. Dust with a soft clean cloth
only.
Check all bolts, screws and legs regularly to make sure they
haven’t loosened and tighten all joins of your furniture or bedstead
after 6 months. Please keep these instructions in a safe place for
further use.
Storage Drawers in Bedsteads are designed to carry lightweight
items such as Pillows, duvets and linen. Please try to avoid storing
heavier items such as books or toys.
Returns
If you have bought a large item such as a bed or mattress which
is damaged or faulty and would like to return it, we will be able
to arrive at your home and take your item away. All we ask is that
your item is in perfect condition and in its original packaging (you
can open the packaging to inspect your item). Items will not be
able to be returned if they are not in their original packaging.
For online and telesales orders, you can only return an item within
14 days from the date of your delivery.
Dreams reserve the right to modify products, dimensions, parts and fixings whithout notification.
www.dreams.co.uk
Thank you for purchasing from
Need assistance?
Call: 0344 292 0000