DREAMS ELLIS BEDSTEAD User manual

Parts Identification
Parts Checklist
Page 1 of 6
4
3
6 7
8
910
5
5
2
*Only supplied if upgraded sprung slat frame system chosen Legs (9&10) only supplied with sprung system
ELLIS BEDSTEAD
160925
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Note:Standard wooden slat frame (part 6)
Upgraded sprung slat frame (part 8)
1
Qty Qty
Ref. Description DescriptionRef.
1
2
3
4
7
6
5
8
9
10
1
1
1
1
1
1
1
1
2
*Upgraded Sprung Slat Frame*
4
Headboard
Footboard
Side Panel - Left
Side Panel - Right
Feet
Wooden Slat Set
Wooden Slat Set Support Leg
*Sprung Slat Frame Centre Support Leg*
*Sprung Slat Frame Support Legs*

QtyCode Description
Ax12
Fittings Checklist
C
x12
Spring Washers (for M8 bolts) D
Flat Washers (for M8 bolts)
Qty
Code Description
BAllen Key (for M8 bolt) x1
Bolts (M8x30mm) for
fitting side panels (3&4)
draobtoof&draobdaehot (1&2)
K x6
Spring Washers (for M6 bolts)
EXTRA HARDWARE NEEDED WHEN FITTING UPGRADED SPRUNG SLAT FRAME
Note: The following fittings will be found in the box which contains the upgraded metal frame itself.
Qty
HARDWARE FOR FITTING WOOD SLATS OR UPGRADED SPRUNG SLAT FRAME (PACK B)
Hx1
Allen Key (for M6 bolt)
F x6
Sleeve Nuts - M6
Bolts (M6x40mm) for
fitting the wooden slat set (6)
or the sprung slat frame (8) to
side panels (3&4)
x6
x7
Flat Washers (for M6 bolts & 5mm screw)
G
E
Screw (5x50mm) for
fitting slat suport leg (7)
J x1
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
x12
Code Description Qty Code Description
Page 2 of 6
L
Bolts (M6x15mm) for fitting
support legs (9&10) to the
sprung slat frame (8)
x8 9
Sprung slat frame
centre support leg
Sprung slat frame support legs
x1
10 x2
In the unlikely event of missing or damaged parts, please
contact the customer service team on 0344 292 00 00.
When calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
Additional Tools Required
General Hints & Tips When they are supplied and are
part of the assembly of this bed,
ensure that the barrel nuts are
fitted the correct way so the
hole in the nut is facing towards
the intersecting hole in the panel.
Intersecting
Hole
Care & Maintenance
Cross-head Screwdriver
We recommend the bed is
assembled in
the room it shall be
located in.
A ssembly requires two persons.
Approximate time to
assemble this product
1.0 HR

Page 3 of 6
Stage
1
Bed Assembly - Use Pack 'A'
Ax8 Cx8 Dx8
E
x1
A
B
C
D
10mm
A
B
C
D
10mm
5
5
5
5
2
1
1
1&
2
2
5

Page 4 of 6
Stage
2
Bed Assembly - Use Pack 'A'
Ax4 Cx4 Dx4
E
x1
1
2
3
4
A
C
DE
E
90%
1
34
&
2
34
&
100%
90%

G x7
F
K
x6
x6
J
x6
x1x1
Page 5 of 6
i)
ii)
iv)
iii)
G
J
Adjustable foot
6
E
K
F
G
6
E
K
F
G
6
7
E
K
F
G
H
Fitting Wooden Slat Set - Use Pack 'B'
Stage
3a
E
Carefully lay the wooden slat
set on the metal supports, on
each side panel.