DREAMS FRANCIS OTTOMAN BEDGAS LIFT User manual

Parts Identification
Parts Checklist
Page 1 of 9
FRANCIS OTTOMAN BED
GAS LIFT
170227
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Qty Qty
Ref. Description DescriptionRef.
1
2
3
4
12
6
5
8
9
1
1
1
1
2
5
1
2
1Feet - Left
13 2
Feet - Right
7 2
Headboard
Footboard
Side Rail - Left
Side Rail - Right
Mattress Base Board - Headend
Mattress Base Board - Footend
Base Boards
Base Board Support Rails (Wood)
Mattress Base Support Rails (Wood)
10 2
Angle Brackets
11 1
Mattress Base Lifting Handle
8
7
7
5
6
11
1
2
3
4
10
9
12
13
L
R

QtyCode Description
Ax16
Fittings Checklist
C
D
Flat Washers (for M8 bolts)
Qty
Code Description
Allen Key (for M8 bolt) x1
Hx8
Bolts (M8x30mm) for
fitting side rails (3&4) to
draobtoof&draobdaeh (1&2)
Bolts (M8x60mm) for
fitting feet (12&13) to
fitting mattress base support rail (9) to
headboard & footboard (1&2)
draobtoof&draobdaeh (1&2)
Qty
HARDWARE FOR FITTING MATTRESS BASE BOARDS (PACK B)
F
G
J
x1
Spanner (for M8 nuts)
Metal Plates for connecting
mattress base boards (5&6)
x2
E
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
x24
Code Description Qty Code Description
Page 2 of 9
CFlat Washers (for M8 bolts) x18
x16
Spring Washers (for M8 bolts)
B
Ax16
Bolts (M8x30mm) for fitting
gas-lift mechanism and metal
connecting plates
(J) to
mattress base boards (5&6).
x8
Spring Washers (for M8 bolts)
B
In the unlikely event of missing or
damaged parts, please
contact the customer service team on 0344 292 00 00.
When calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
Additional Tools Required Care & Maintenance
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
General Hints & Tips
When they are supplied and are
part of the assembly of this bed,
ensure that the barrel nuts are
fitted the correct way so the
hole in the nut is facing towards
the intersecting hole in the panel.
Intersecting
Hole
We recommend the bed is
assembled in
the room it shall be
located in.
A ssembly requires two persons.
Approximate time to
assemble this product
1.5 Hrs
Flange Lock-Nuts (M8)
for gas-lift pistons.
x2
x2
Domed nuts (M8) for fitting mattress
base lifting handle (11) to mattress
base board (6).
No Additional Tools Required

R
R
L
L
Page 3 of 9
Stage
2
Bed Assembly - Use Pack 'A'
x8 B x8A C x12
Dx1
Stage
1
x4
HC x4
Dx1
H
ABC
C
2
9
1
C
H
D
C
H
D
12
1
1 2
&
2
13
x4H
ABC
H
C
9
Note angles
point inside
CBAD
10mm

Page 4 of 9
Stage
3
Bed Assembly - Use Pack 'A'
Stage
4
Dx1
1
2
3
4
D
34
&
12
&
90%
2
10
3
A
BC
4
&
A x8 B x8 C x8
D
x1
44
3
2
100%
Make certain the bed is squared up
as shown in the diagram then tighten
all bed assembly bolts 100%.

Page 5 of 9
Stage
5
Stage
6
Base Board Assembly
x5
8
34
&
7
8

Page 6 of 9
Gas Lift Assembly
Stage
7
ii) Lift up mattress base board support bars.
i) Un-tie the two mechanisms.
SMALL GAP
F
G
G
G x2
Fx1
Hold up each arm and slide piston stem onto the threaded axle and
fit nut (G) using spanner (F).
Note, do not overtighten - a small gap needs to be left - see sketch.
Slide in the headend baseboard (5).
iii) Connect the piston stems

Page 7 of 9
Mattress Base Assembly - Use Pack 'B'
Stage
8
x8 B x8
A C
J
x8
x2
Dx1
5
A
A
D
D
B
C
C
J
5
BEFORE FITTING (6) FIT BOTH PLATES (J) TO HEADEND MATTRESS BASE FIRST
SLIDE HEADEND MATTRESS BASE BOARD (5)
UP AGAINST THE LIFTING ARM STOP PLATES.
CAREFULLY SCREW BOLT SETS INTO BASE
BOARD AS SHOWN - DO NOT TIGHTEN 100% YET.
5

Mattress Base Assembly - Use Pack 'B'
x8 B x4
A C x10
Dx1
Page 8 of 9
Stage
9
6
A
C
A
D
B
C
E
F
C
A
B
C
100%
E x2
Fx1
9
6
SLIDE FOOTEND MATTRESS BASE BOARD (6) INTO POSITION
LOOSLEY CONNECT THE PLATES SCREWING ALL 8 SETS OF BOLTS INTO PLACE
WHEN ALL BOLTS ARE IN PLACE, TIGHTEN ALL 16 BOLT SETS 100%
5
5
6

NOTE: Before lifting the mattress base, place the mattress on the top. Without a mattress in place, the
speed of movement is quick and may cause injury. Carefully lower the frame holding the handle firmly.
Depending on the weight of the mattress, the rising & lowering speed will vary so be careful until you
get used to the speed. Always use the handle to lift or lower the frame - keep fingers well away from
the moving parts.
When fully assembled and with the mattress in position, please raise & lower the ottoman 4/5 times to
ensure the gas pistons are fully lubricated.
Page 9 of 9
Note: Be very careful what you
store under the bed - the top of
an item, like a suitcase or a box,
must not touch the underside of
the mattress base or it may get
damaged.
Maximum item height is 210mm.
Warning.!
Stage
10
Base Board Assembly
7