DREAMS TEMPUR Reign Ottoman User manual

1 hour approx
assembly time
Two person
assembly
Reign Ottoman Bed

Thank you
Hello, thanks for choosing to purchase your bed from Dreams - you're now on your way to your best
ever night's sleep. Before you begin building your bed, please take a moment to read through the
instructions and make sure that you've got all the relevant parts listed on the following pages.
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your bed.
e advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
Top tip
e recommend that you build your new bed in the room you’d like it to be
located - this will help prevent any risk of damage to your newly built bed
whilst moving it.
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this bed which could
present a choking hazard. All plastic and wrapping materials should also be
kept away from children and animals to prevent any risk of suffocation.
To keep your little ones busy, there is a colouring page inside the back cover.
Help and support
At Dreams, it’s our mission to give the whole nation a great night’s sleep - this
means that the quality of our products is of utmost importance to us. If there
are any issues with your product or any missing parts, please visit our website
at www.dreams.co.uk/help
ecycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.
Duke Bed - Assembly Guide - Page 2
Top tip
e recommend that you build your new bed in the room you’d like it to be
located - this will help prevent any risk of damage to your newly built bed
whilst moving it.
Reign Ottoman Bed - Assembly Guide - Page 2

Parts
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 3
Parts list
A. Headboard 1pcs
B. Footboard 1pcs
C. Side panel(Left Right) 2pcs
D.
Base boards 2pcs
E.
Slat frame 2pcs
F.
Ottoman arms (Left Right) 2pcs
G.
Piston 2pcs
H.
Bar 2pcs
I.
Mattress stopper 2pcs
J.
Rope 2pcs

Fittings
Please check you have all the parts listed below with your product:
0 1 2 3 4 5 6 7 8 9
cm
10 11 12 13 14 15 16 17
Tools required
Please check you have all these below:
Scissors Tape measure Cross head screwdriver
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 4

Assembly
1
2
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 5
(1).Attach the side panels (C)to the
behind the flat washers.Loosley screw
in the bolts but do not tighten them
(1).Attach the footboard in the same
headboard(A)locating the brackets
yet.
way as the headboard.

Assembly
3
4
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 6
(1).Make certain the bed is squared
fully tighten all the bolts.
(1).Place the base boards into the
up as shown in the diagram,then
bottom of the bed.

Assembly
5
6
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 7
(1).Attach the lock ( ) to the
ottoman arm (F).
H3
(1).Attached the piston to the ottoman
arm,make sure the piston is assembled
the correct way round,the black section
attaches to the top of the frame (as per
the image).

Assembly
8
7
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 8
(1).Using bolts (H8)fit the ottoman arms
to the side rail (C) and fully tighten all
(1).Attach the bar ( )to the
slat frame( ).
H11
Using bolts( ),nut( ),metal washers
E
( )fit two bar of the slat frame,using
allen key( )and spanner ( )tighten
H5 H2
H6 H7
(2)Using bolts( ),nut( ),metal washers
( )fit two slat frame,using
and spanner ( )tighten all bolts .
H4 H2
H6
allen key( )
H7
the bolts.
H9
all bolts .
H9

Assembly
9
10
9
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page
(1).Attach the slat frame ( )to the
behind the flat washers.Loosley screw
(1).Push mattress stoppers( )x 2
ottoman arms(F).
looslet fix the slat frame to
I
into metal frame.
(2).Push rope( )x 2
J
frame.
into metal
E
Using two bolt sets on each side (
H1,
H2,H6,H7,H9),
to the arm once all 4 bolt sets are in
place,please then fully tighten all the
bolts.

Care and maintenance
Here are some tips to keep your new bed in tip-top condition
Cleaning
To clean your new bed, we'd advise using a warm damp cloth - please do not
use abrasive chemicals or bleach as this may damage the product.
Checking and moving
Periodically we recommend you check that the screws or fixtures haven't
become loose, over time. To move your new bed, we recommend lifting it where
possible, as dragging or pushing it could cause damage to your flooring.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Fabric
Please note depending on the lighting, positioning and surroundings of your
room, the colour of the fabric can sometimes appear slightly di fferent. Over a
period of time, the colour might lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. e recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Thank you for shopping with us - we hope you have
a great night's sleep
Sleep we
Duke Bed - Assembly Guide - Page 2Reign Ottoman Bed - Assembly Guide - Page 10