DREAMS Glacier King Bed User manual

215-00945 (Solid slats)
Glacier King Bed 215-00946 (Sprung slats)
Assembl
y
Instructions
1. We suggest you spend a short time reading through this leaflet and then
follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the.
Assembly should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children’s reach.
In the unlikely event that this product has missing or damaged parts, please call
08442 920000 to obtain spares
Before you
Start, here
are some
helpful
advices.
Revision number 1/1

AM6×15mmx16pcs
B
M6×10mm x 14pcs
C
M6×35mm x 6pcs
D
M6 × 6pcs
E
Washer (16mm) x 22pcs
F
Plastic Washer x 16pcs
G
Allen key × 2pcs
H
Spring washer x 16pcs
I
Washer (13mm) x 14pcs
Revision number 1/1
PARTS Fittin
g
s
A
(9) HB Panel 1
(10) HB cross tubing 1
(7) Long canopy rails 2
(8) Short canopy rails 2
(6) Cross rails 2
(5) Side Rails 2
(4) Top Posts 4
(3) FB bottom post 2
(2) HB bottom post left 1
(1) HB bottom post right 1
NO. PART LIST QTY

ASSEMBLY
STEP1
Revision number 1/1
(1).将上立柱花(4)螺孔依次
对准右下立柱花（1）、左
下立柱花（2）、前下立柱
花（3）上的牙杆，上立柱
花(4)向下旋转,直至锁紧锁
到位
Attach Cross rails (6) to HB
bottom posts (1)(2)(3) by
using bolts A, Plastic washer
F, washer E, Spring Washer
H, and tighten with Allen Key
G.
Attach Side rail (5) to HB
bottom posts (1)(2)(3) by
using bolts A, Plastic washer
F, washer E, Spring Washer
H, and tighten with Allen Key
G.

Insert ends of HB panel (9)
and HB Cross tubing (10)
into holes on HB bottom
posts (1)(2), secure the HB
panel (9) onto posts by
using bolts B, washer I and
tighten with Allen Key G.
ASSEMBLY
STEP 2
Revision number 1/1

ASSEMBLY
STEP 3
Screw the Top Posts (4)
onto bottom posts
(1)(2)(3) by turning the
top posts (4) clock-wise.
Revision number 1/1

ASSEMBLY
STEP4
Loosen the metal balls on
top of posts, align the top
section of the posts in
right angle. And insert the
canopy rails (7)(8) into
holes on top posts (4).
Secure the canopy rails
(7)(8) onto top posts (4)
by using bolts B, washer I,
and tighten with Allen Key
G.
Tighten the metal balls on
top of posts.
Revision number 1/1

ASSEMBLY
STEP5
NOTE: Slats not supplied shown
for reference only.
Both slats on "step 5" and "step
6" can be assembled to the
bedstead. you can make a choice
between the two slats.
OPTION"A": DREAMS FIXED
WOOD SLATS
（1）Carefully locate the slats
onto the unit.
（2）Use bolt (C) and JCN nut
(D) to fix the unit using Allen Key
(G)
Revision number 1/1

ASSEMBLY
STEP6
OPTION"B":DREAMS
SPRUNG SLATS
(1) Use the bolt to fix support
leg onto the slat frame. Please
note that these bolts are to be
found inside the slat frame box.
(2) Carefully locate the slats
onto the unit.
(3) Use bolt (B) and JCN nut
(C) to fix the unit using Allen
Key (F).
Revision number 1/1