DREAMS OSWALD BED User manual

OSWALD BED
Assembly Instructions
Need assistance?
Call: 0344 292 0000
Dimensions mm Length Width Height
Single 2015 965 1085
Approximate time to
assemble this product
Retain these instructions
for future reference
2 x people recommended to
assemble this product
Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fixings.
You will require a cross
head screwdriver
Helpful advise before you begin:
1. We suggest you spend a short time reading through this leaflet
and then follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be
worth the effort.
3. Do not discard any of the packaging until you have checked that
you have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings
are only finger tightened during initial assembly. Only upon
completion of the assembly should all fixing points be fully
tightened.
6. We recommend a periodic check on all fixing points to make
sure they remain fully tightened.
7. Keep glue and fittings out of children’s reach.
8. Do not use any other tools other than those recommended to
build this product.
9. Please do not use substitute parts. Use only additional or
replacement parts supplied by Dreams Ltd.
10. In the unlikely event that this product has missing or damaged
parts, please call 0344 292 0000 to obtain spares.
Page 1 of 8

Page 2 of 8
Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fixings.
Parts Checklist
01 Head Board
Foot Board
Back Bar
02
03
Side Rail x2pcs
04
Back Frame
05
01
02
03
03
04
04
05
Ø24 Rubber Washer
Fittings Checklist
M6 x 20mm Bolt
x 4
x 16
M5 x 21mm Bolt
Ø16 Metal Washer
Ø21 Metal Washer
Allen Key
Check size of fixings against this guage (dimensions in mm)
1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 10 0 11 0
x 8
x 14 x 1
x 1
x 2
x 6
G
A
M5 x 13mm Bolt
x 6
C
B
D
E
H
I
N
Washer
x 8
O
Ø5 x 43mm
Tapping Screw
Center Leg
Inner Bolt
x 6
F

Page 3 of 8
Bed Frame Assembly
1
x 2
x 2
2
x 4
M6 x 20mm Bolt x 4 Washer x 1 Allen Key
N
AO
A
A
Do not tighten any of
the bolts until the item
is fully assembled.
Do not tighten any of
the bolts until the item
is fully assembled.
x 4
M6 x 20mm Bolt
A
x 4
Washer
O
01
01
01
02
02
02
03
03
05
05
N
N
O
O

x 4
x 8
Ø24 Rubber Washer
G
x 8
M6 x 20mm Bolt
A
x 8
Ø16 Metal Washer
D
Page 4 of 8
Bed Frame Assembly
3Fully Tighten bolts when the
bed frame is assembled
and in position
A
A
D
D
G
G
01
01
02
04
04
04
N

Page 5 of 8
Identify the slat system you have purchased...
Standard wooden slat system
Sprung slat system
Turn to steps A
Turn to step D,E & F
x1
x1
06
07
x1
Adjustable Foot
I