DREAMS HART LIFESTYLE BED SLEEPMOTION User manual

Two person
assembly
2hour approx
assembly time
MK1 220419
HART LIFESTYLE BED
SLEEPMOTION

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 2
Thank you
Hello, thanks for choosing to purchase your bed from Dreams - you're now on your way to your best
ever night's sleep. Before you begin building your bed, please take a moment to read through the
instructions and make sure that you've got all the relevant parts listed on the following pages.
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your bed.
We advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
Help and support
At Dreams, it’s our mission to give the whole nation a great night’s sleep - this
means that the quality of our products is of utmost importance to us. If there
are any issues with your product or any missing parts, please contact our Help
Centre on 0800 652 6750, where a member of our team will be happy to help.
(For customers based in Northern Ireland, please call 028 9050 8300)
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this bed which could
present a choking hazard. All plastic and wrapping materials should also be
To keep your little ones busy, there is a colouring page inside the back cover.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.
We recommend that you build your new bed in the room you’d like it to be
located - this will help prevent any risk of damage to your newly built bed
whilst moving it.
Top tip

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 3
Parts
The bed you have purchased comes with a Sleepmotion Lifestyle electric base.
Complete the assembly of the Sleepmotion base before assembly of the bed frame. Assembly Instructions are
included within the Sleepmotion base carton.
Once the base is assembled in the final location, follow the steps below to build your bed frame around it.
The dotted lined parts shown are
packed in the sleepmotion bed base
carton itself.
Parts list
C
C
B
A. Headboard 1
B. Footboard 1
C. Side rails 2
Tools required
Please check you have all these below
Tape measure
0 1 2 3 4 5 6 7 8 9 1010 11 12 13 14 15 16 17 18cm
Spring washer for M8 bolts
Bolts (M8x30mm) for fitting
side rails (C) to headboard &
footboard
a x14 b x14
Flat washer for M8 bolts
c x14
Allen Key for M8 bolt
d x1
A
q x6
Bolts (M8x40mm) for bolting
wings to main headboard
Spring washer for M8 bolts Flat washer for M8 bolts
b x6 c x6 d x1
Allen Key for M8 bolt
Fittings
Please check you have all the parts listed below with your product:
Hardware pack (A) needed for fixing wings to headboard
Packed in side rails - Pack 3L
Hardware pack (B) needed for fixing side rails to headboard & footboard
Packed in side rails - Pack 3L

Before starting assembly please refer to the owners
manual supplied with your sleepmotion bed base and
follow the instructions taking note of any safety
precautions or operational safety requirements of the
installation.
In the room where bed will be used, first prepare the bed base by fitting the eight long
legs - 6‘’ (15cm), see Step 3.
Connect the power and check the operation then step by step follow the bed assembly
instructions below, to build the bedstead around the sleepmotion 200i bed base.
Important:
Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 4
1Headboard assembly.
Unfold wings & un-zip compartments.
q
x6
b
x6
c
x6
d
x1
q
cb
d
Using Hardware Pack (A), unfold and bolt
each wing to the main headboard. Screw
three bolt sets (q, b & c) into the pre-tapped
holes on each side,tighten with allen key (d).
i)
ii)
Left
Right

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 5
Firstly screw in the eight
6" (15cm) legs as shown.
2 Prepare the bed for assembly.
A
B
a
x8
b
x8
c
x8
10mm
a
c
b
10mm
a
c
b
3Assemble the bed frame around the bed base.

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 6
4
ax2 bx2 cx2 dx1
C
a
b
cd
90%
10mm
20mm
Position the electric . bed base.
Place the headboard in the location in which the bed shall be used and attach the right
hand side rail using bolt sets (a, b & c). Make sure the bed base is correct way round
with mattress stopper at the foot end. Carefully lift and place bed base into the corner
between headboard and side rail as shown - it is heavy so please get help.
A
Make sure the gap is as per the drawing.
ii)
i)

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 7
5
6
ax1 bx1
cx1 dx1
B
Position footboard and connect to the side rail brackets.
i) Connect Power Lead for electric base to your wall socket - for safety this must be an
earthed power supply.
ii) Raise the head and foot ends of the bed base using the bed base remote control.
B
a
c
b
d
90%
C
Connect power to the electric bed base.

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 8
C
7
abc
d
90%
100%
ax3 bx3 cx3 dx1
B
A
a
cb
d
90%
C
C
Make certain the bed is squared up as
shown in the diagram then tighten all
bed assembly bolts 100%.
Make sure everything is working properly then fit the left hand side rail.

Hart Sleepmotion Lifestyle Bed - Assembly guide - Page 9
8
10mm
30mm
10mm
20mm
Check that there is the correct gap around the perimeter of the bed base.

Care and maintenance
Here are some tips to keep your new bed in tip-top condition
Hart Sleepmotion Lifestyle Bed - Care and maintenance guide - Page 10
Cleaning
To clean your new bed, we'd advise using a warm damp cloth or if fabric, remove
dust using a low suction vacuum cleaner.
Please do not use abrasive chemicals or bleach as this may damage the product.
Checking and moving
Periodically we recommend you check that the screws or fixtures haven't become
loose over time. To move your new bed, we recommend lifting it where possible, as
dragging or pushing it could cause damage to the legs or flooring.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Fabric
Please note depending on the lighting, positioning and surroundings of your
period of time, the colour might lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. We recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Thank you for shopping with us - we hope you have a
great night's sleep.
L
38
4
9
5
W
H
3
Overall Dimensions (LWH cm)
Double: 207 x 233 x 116
King: 217 x 248 x 116
Internal Dimensions (LW cm)
Double: 193 x 138
King: 203 x 153
33.5
Floor to top
of base.
4.5
Top of side rail
to top of base

Little dreamers
Keep the little ones entertained while
you assemble your new purchase.