DREAMS LUCIA User manual

11
10
14
9
12
11
15 15
16
3
5
1
2
Drawer parts
LUCIA STORAGE BED
SINGLE SIZE
Parts Identification
PLEAS
DRAWER ON RIGHT
DRAWER ON LEFT
E READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be
kept away from young children during assembly, to avoid
the danger of choking.
Parts Checklist
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - P LEASE READ THESE INSTRUCTIONS CAREFULLY
6
8
7
Page 1 of 8
*
Only supplied if upgraded sprung slat frame is chosen.
Note that in this application, Leg (8) is not required - do not
fit to slat frame or drawer cannot slide into position.
160405
4a
6 1
Headboard
Footboard
Side Panel (Drawer - can fit to left or right side)
Adjustable Support Legs
Side Panel (Solid)
Wooden Slat Set
7
8
10
Drawer Back Panel
Drawer Bottom Panel
Drawer Face Panel 1
11 Drawer Side Panels 2
Ref. QtyRef. Description
12 Drawer Front Panel 1
1
1
16 1
*Upgraded Sprung Slat Frame*
*Sprung Slat Frame Centre Support Leg*
9 1
14
Drawer Bottom Support Rails
11
Drawer Bottom Support Rail
2
5
Qty
1
2
3
1
1
1
Description
4a&4b 1
Pr
15
4b
Please read note below.
This leg (8) should not be fitted to
the slat frame - it is NOT needed.
Note - Either a Std wooden Slat Set (6), or if chosen at time of
purchase, an upgraded Sprung Slat Frame (7) & Leg (8), shall
be supplied in a separate box.

QtyCode Description
Ax16
Fittings Checklist
C
x16
Spring Washers (for M8 bolt)
D
Qty
Code Description
B
M
Allen Key (for M8 bolt) x1
Page 2 of 8
Bolts (M8x30mm) for
fitting side panels (3&5)
to headboard & footboard (1&2).
Flat Washers (for M8 bolt)
QtyCode
K
Plastic Barrel Nuts x14
Screws (3x20mm) for fitting
wheel (N) to wooden drawer
support rails.
x20
S
LScrews (4x30mm) for fitting
drawer face panel (10) x8
NDrawer Wheels x5
Bolts (M8x45mm)
for fitting adjustable
support legs (4) to
side panel (3).
x4
Vx6
Spring Washers (for M6 bolt)
P
Bolts (M6x15mm)
x4
EXTRA HARDWARE SUPPLIED WITH THE UPGRADED SPRUNG SLAT FRAME.
NOTE THAT THESE PARTS ARENOT TO BE FITTED IN THIS LUCIA SINGLE BED.
8
Support leg
x1
Qty
HARDWARE FOR FITTING WOOD SLATS OR UPGRADED SPRUNG SLAT FRAME (PACK B)
H x1
Allen Key (for M6 bolt)
F x6
Sleeve Nuts - M6
x6
x6
Flat Washers (for M6 bolt)
G
E
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
HARDWARE NEEDED FOR DRAWER ASSEMBLY (PACK C)
Description
Qty
Code
WHEELS FOR DRAWER (PACK D)
Screws (5x50mm) for
assembling drawer panels
Jx14
Description
x20
Code Description Qty Code Description
Bolts (M6x40mm) for fitting
the wooden slat set (6) or
the sprung slat frame (7) to
side panels (3&5)

Page 3 of 8
In the unlikely event of missing or damaged parts, please
contact the customer service team on 0344 292 00 00.
When calling
this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
Additional Tools Required
General Hints & Tips When they are supplied and are
part of the assembly of this bed,
ensure that the barrel nuts are
fitted the correct way so the
hole in the nut is facing towards
the intersecting hole in the panel.
Intersecting
Hole
Care & Maintenance
Cross-head Screwdriver
We recommend the bed is
assembled in
the room it shall be
located in.
Stage
1MC
ARROWS ON LABELS POINT
TOWARDS EACH OTHER
M
C
C
3
4a
4b
Bed Assembly - Use Pack 'A'
x4x4
D
x1
Carefully adjust feet so they just touch the floor
keeping side panels level when bed is in use.
Adjustable Feet
Fix support legs (4) from inside bed frame into
the pre-threaded holes in both side panels (3).
Make certain the labels are as shown in the
diagrams - they must point towards each other.
The legs are then in correct place to stop the
drawer going under the bed.
This assembly requires two persons.
Approximate time to
assemble this product
40 MINS

Stage
2
Ax16 Bx16 Cx16
Page 4 of 8
D
x1
A
B
C
2
5
3
1
FIT BOLTS TO
HEADBOARD &
FOOTBOARD
LIKE THIS.
10mm
a.
b.
&&
5
3
&
11
22
5
5
3
3
Bed Assembly - Use Pack 'A'
MAKE CERTAIN THE BED IS
SQUARED
UP, AS SHOWN IN THE DIAGRAM.
Once all four corners are located, make sure the bed is still
square, then tighten all the bolts 100% using Allen key (D).
Fit the side panels locating the brackets behind the flat
washers.
Loosely insert four bolts (A) with spring washers (B) & flat washers (C) into each side of
headboard & footboard (1&2).
Note: Do not tighten fully but leave 10mm protruding as in the diagram.
DRAWER ON RIGHT DRAWER ON LEFT
NOTE THAT THE DRAWER CAN BE FITTED ON THE LEFT or
THE RIGHT SIDE OF THE BED - CHOOSE WHICH SIDE YOU
WANT THE DRAWER & FIT SIDE PANEL (3) IN THAT POSITION.

Stage
3a
Page 5 of 8
i:
ii:
iii:
6
E
V
F
G
G x6
F
V
Carefully lay wooden slat set (6) on the metal supports
on each side panel.
x6
x6
E x6
H x1
Fitting Wooden Slat Set - Use Pack 'B'
6
E
V
F
G
6
E
V
F
G
Roll out rest of wooden slats and
fix with last two bolt sets fully
tighten using Allen key (H).
Using two bolts (E) with
spring washers (V), flat
washers (G) and sleeve
nuts (F) fix one slat next
to headboard.
Roll out wooden slats just
over half way down the bed
and using two more bolt sets,
loosely bolt the central slat
into position - align slats and
fix all four bolt sets 100%
by Allen key (H).
6

Stage
3b
Page 6 of 8
G x4F
H
x4E x4
x1
V x4
7
E
F
G
V
Open the sprung slat frame and lay face down on the working surface.
Carefully turn the slat frame over and position onto the metal slat
supports on each side panel. Align the frame with the fixing holes at
each end and secure using four sets of bolts (E), spring washers
(V), flat washers (G) and sleeve-nuts (F).
When all in place tighten using allen key (H).
Finally, please check carefully that all bolts are fully
tightened before the bed is used.
7
Fitting Upgraded Sprung Slat Frame - Use Pack 'B'

4
12
i:
9
J
S
Page 7 of 8
IMPORTANT:
MAKE SURE WHEN
FITTING THE NUTS
THAT THE HOLE IS IN
CORRECT ALIGNMENT
WITH THE HOLE IN THE
PANEL EDGE.
16
15
S
S
S
S
S
S
S
S
S
S
S
S
S
x14 x14
Drawer Assembly - Use Pack 'C'
Stage
11
ii:
14
12
11
9
15 16
15
iii:
iv:
v:
vi:
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Stage
5
Stage
6
L
SLIDE IN THE DRAWER
Page 8 of 8
NK
Drawer Assembly - Use Pack 'C & D'
x8 x20 x5
K
K
KK
N
Fit the assembled drawer to rear
of Drawer Face Panel (10).
Carefully follow the guide lines
on inside face of the rear side.
L
10
L
LLL
LL
L