Dremel 3D20 Idea Builder User manual

IMPORTANT: IMPORTANT: IMPORTANTE:
ReadBefore UsingLire avant usage Leerantes de usar
Operating/SafetyInstructions
Consignesde sécurité/d’utilisation
Instruccionesde funcionamientoy seguridad
3D20 Quick Start Guide
Unboxing
1Kit Contents
2
WARNINGWARNING
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
ENGLISH

IMPORTANT: IMPORTANT: IMPORTANTE:
ReadBefore UsingLire avant usage Leerantes de usar
ForEnglishVersion Versionfrançaise Versiónenespañol
Seepage 2 Voir page37 Verla página 73
Operating/SafetyInstructions
Consignesde sécurité/d’utilisation
Instruccionesde funcionamientoy seguridad
1-844-4DRML3D(1-844-437-6533) www.dremel.com
CallTollFree for
ConsumerInformation
&Service Locations
Pourobtenir des informations
etles adresses de noscentres
deservice après-vente,
appelezcenumérogratuit
Llamegratis para
obtenerinformación
parael consumidory
ubicacionesde servicio
P
.O.Box 081126 Racine, WI 53408-1126
3D20
Idea Builder
3D20 Quick Start Guide
WARNINGWARNING
READALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
DREMEL3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAYRESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
0
.
3
m
m
C
L
E
A
R
A
N
C
E
LEVELING SHEET
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
Adjust the platform until
leveling tool slides between
the extruder and platform
with some resistance
0.3mm
LEVELING TOOL
Unboxing
1
Getting to Know Your Dremel 3D20
3
1. Lid
2. Door
Kit Contents
2
TIP: Save your Dremel 3D20 packaging for future transportation and storage.
Dremel 3D20 Instruction Manual Quick Start Guide 1 Filament Spool
Power CableSpool Lock USB Cable SD Card
Build Tape Object Removal Tool Unclog Tool Leveling Sheet
1
8
1
2
3
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 1: LEFT ADJUSTMENT
NEXT
WARM
Getting Ready to Build (continued…)
5
LEVELING BUILD PLATFORM
1. Tap “Tools” on your Dremel 3D20’s touch screen and
tap “Level”.
2. First level the front left of the build platform.
3. Place the leveling sheet between the extruder and build
platform.
a) If the leveling sheet cannot slide between the extruder
and build platform, turn the knob counterclockwise until
you can slide the leveling sheet between the extruder and
build platform with some resistance.
b) If the leveling sheet can slide between the extruder and
build platform too easily, turn the knob clockwise until you
can slide the leveling sheet between the extruder and build
platform with some resistance.
4. Tap “Next” to move the build platform toward the right knob
and repeat step above.
1 2
3
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
English

PRESS
Getting to Know Your Dremel 3D20
3
Getting Ready to Build
4
1. Lid
2. Door
3. Touch Screen
4. Build Platform
5. Build Platform Clips
6. Filament Spool
7. Filament Spool Holder/Lock
8. Extruder Tip
9. Extruder Fan
10. Extruder
11. Extruder Intake
12. X-Axis Guide Rails
13. Stepper motor (1 of 3)
14. Z-Axis Guide rail
15. Filament Guide Tube
16. Y-Axis Guide Rails
17. SD card Input
18. USB Input
19. Power Switch
20. Power Input
1
2
3
4
5
6
7
8
9 1011 12
13
14
15
16
17 18 19 20
WARNINGWARNING
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
INSTRUCTIONS WHEN USING THE DREMEL 3D20.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 2: RIGHT ADJUSTMENT
NEXT
WARM
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 3: BACK ADJUSTMENT
NEXT
WARM
a) If the leveling sheet cannot slide between the extruder
and build platform, turn the knob counterclockwise until
you can slide the leveling sheet between the extruder and
build platform with some resistance.
b) If the leveling sheet can slide between the extruder and
build platform too easily, turn the knob clockwise until you
can slide the leveling sheet between the extruder and build
platform with some resistance.
4. Tap “Next” to move the build platform toward the right knob
and repeat step above.
5 Tap “Next” to move the build platform toward the rear knob
and repeat step above.
6. Tap “Finish” to complete the leveling process.
Building
6
BUILDING OUT OF THE BOX
1. Go back to the main screen on your touch screen and insert
SD card included with your Dremel 3D20.
2. Tap “Build” on the touch screen, tap the SD card option, and
use the up/down arrows to scroll.
3. Tap on the model file you would like to build and tap "Build".
4. Your Dremel 3D20 will align the extruder with the build
platform and will begin heating the extruder.
5. Once the build temperature is reached, your model will
begin to build.
6. Touch screen will display “Object Finished”. Tap the check
box to confirm. Wait until the touch screen indicates that
the extruder temperature is “COOL”.
1 2
3
4 5
1 2
3 5
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER

Filament
Guide
PRESS
LIFT
Getting Ready to Build
4
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position, remove the lid
and remove the build platform.
2. Place filament spool onto spool holder with spool being fed from
the bottom towards the back of the Dremel 3D20. Insert spool
lock into spool holder and rotate 90 degrees to lock in place.
3. Thread filament through filament guide tube.
4. Insert the filament coming from the filament guide tube into
the extruder intake (top).
5. Adhere build tape over the build platform.
6. Install the build platform using the build platform clip
to secure.
7. Plug power cord into outlet and turn on power switch.
8. Tap “Tools” on your Dremel 3D20’s touch screen, then tap
“Filament”, then tap “Load Filament” and wait for the extruder
to heat.
9. Once heated, filament will drawn through the extruder. Allow
filament to exit the extruder for 10 seconds before tapping the
return arrow to complete.
WARNINGWARNING
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
INSTRUCTIONS WHEN USING THE DREMEL 3D20.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
PROPERTY DAMAGE OR PERSONAL INJURY.
2
3
5
1
8
4
SIDE 1
PRESS COLORS
4. Your Dremel 3D20 will align the extruder with the build
platform and will begin heating the extruder.
5. Once the build temperature is reached, your model will
begin to build.
6. Touch screen will display “Object Finished”. Tap the check
box to confirm. Wait until the touch screen indicates that
the extruder temperature is “COOL”.
REMOVING YOUR OBJECT FROM THE BUILD
PLATFORM
7. Wait for the extruder to cool before removing your object.
8. With the object still attached, remove build platform from
the build area.
9. Use your hand to peel your object from the build platform. If
needed, gently use the object removal tool to remove object
from build platform.
Best Practices & Resources
7
BEST PRACTICES
1. ALWAYS USE BUILD TAPE.
2. Ensure your build platform is level before every object.
3. Ensure spool is installed properly and can rotate freely.
4. When loading filament, allow Dremel 3D20 to extrude until
material is consistent with the installed filament color.
5. It is important to stay near your Dremel 3D20 during
operation and watch the Dremel 3D20 begin building
objects.
6. Use object removal tool gently to avoid damaging the build
platform or object.
7. Remove the build platform before removing the object.
OPERATING ENVIRONMENT
Room Temperature: 16-29° C (60 - 85° F)
Level workspace
Dry workspace environment
15.7” (400mm)
19.1” (485mm) 13.2” (335mm)
WALL
8” (203mm)
8” (203mm)8” (203mm)
14” (356mm)
3D20 RESOURCES
1 2
3 5
9

ForEnglish VersionVersionfrançaise Versiónenespañol
Seepage 2 Voir page37 Verlapágina 73
1-844-4DRML3D(1-844-437-6533) www.dremel.com
merInformation
&Service Locations
Pourobtenir des informations
etles adresses de noscentres
deserviceaprès-vente,
appelezce numérogratuit
Llamegratis para
obtenerinformación
parael consumidory
ubicacionesde servicio
-1126
WARNINGWARNING
READALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
DREMEL3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAYRESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
0
.
3
m
m
C
L
E
A
R
A
N
C
E
LEVELING SHEET
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
Adjust the platform until
leveling tool slides between
the extruder and platform
with some resistance
0.3mm
LEVELING TOOL
Getting to Know Your Dremel 3D20
3
1. Lid
2. Door
3. Touch Screen
4. Build Platform
5. Build Platform Clips
6. Filament Spool
7. Filament Spool Holder/Lock
8. Extruder Tip
9. Extruder Fan
10. Extruder
11. Extruder Intake
TIP: Save your Dremel 3D20 packaging for future transportation and storage.
Dremel 3D20 Instruction Manual Quick Start Guide 1 Filament Spool
Power CableSpool Lock USB Cable SD Card
Build Tape Object Removal Tool Unclog Tool Leveling Sheet
1
2
3
4
5
6
7
8
1
2
3
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 1: LEFT ADJUSTMENT
NEXT
WARM
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 2: RIGHT ADJUSTMENT
NEXT
WARM
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 3: BACK ADJUSTMENT
NEXT
WARM
Getting Ready to Build (continued…)
5
LEVELING BUILD PLATFORM
1. Tap “Tools” on your Dremel 3D20’s touch screen and
tap “Level”.
2. First level the front left of the build platform.
3. Place the leveling sheet between the extruder and build
platform.
a) If the leveling sheet cannot slide between the extruder
and build platform, turn the knob counterclockwise until
you can slide the leveling sheet between the extruder and
build platform with some resistance.
b) If the leveling sheet can slide between the extruder and
build platform too easily, turn the knob clockwise until you
can slide the leveling sheet between the extruder and build
platform with some resistance.
4. Tap “Next” to move the build platform toward the right knob
and repeat step above.
5 Tap “Next” to move the build platform toward the rear knob
and repeat step above.
6. Tap “Finish” to complete the leveling process.
1 2
3
4 5
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
English

Filament
Guide
PRESS
LIFT
Getting Ready to Build
4
4. Build Platform
5. Build Platform Clips
6. Filament Spool
7. Filament Spool Holder/Lock
8. Extruder Tip
9. Extruder Fan
10. Extruder
11. Extruder Intake
12. X-Axis Guide Rails
13. Stepper motor (1 of 3)
14. Z-Axis Guide rail
15. Filament Guide Tube
16. Y-Axis Guide Rails
17. SD card Input
18. USB Input
19. Power Switch
20. Power Input
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position, remove the lid
and remove the build platform.
2. Place filament spool onto spool holder with spool being fed from
the bottom towards the back of the Dremel 3D20. Insert spool
lock into spool holder and rotate 90 degrees to lock in place.
3. Thread filament through filament guide tube.
4. Insert the filament coming from the filament guide tube into
the extruder intake (top).
2
3
4
5
6
7
9 1011 12
13
14
15
16
17 18 19 20
WARNINGWARNING
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
INSTRUCTIONS WHEN USING THE DREMEL 3D20.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
PROPERTY DAMAGE OR PERSONAL INJURY.
2
1
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 2: RIGHT ADJUSTMENT
NEXT
BACK
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
THE BUILD PLATFORM
STEP 3: BACK ADJUSTMENT
NEXT
6. Tap “Finish” to complete the leveling process.
Building
6
BUILDING OUT OF THE BOX
1. Go back to the main screen on your touch screen and insert
SD card included with your Dremel 3D20.
2. Tap “Build” on the touch screen, tap the SD card option, and
use the up/down arrows to scroll.
3. Tap on the model file you would like to build and tap "Build".
4. Your Dremel 3D20 will align the extruder with the build
platform and will begin heating the extruder.
5. Once the build temperature is reached, your model will
begin to build.
6. Touch screen will display “Object Finished”. Tap the check
box to confirm. Wait until the touch screen indicates that
the extruder temperature is “COOL”.
REMOVING YOUR OBJECT FROM THE BUILD
PLATFORM
7. Wait for the extruder to cool before removing your object.
8. With the object still attached, remove build platform from
the build area.
9. Use your hand to peel your object from the build platform. If
needed, gently use the object removal tool to remove object
from build platform.
4 5
1 2
3 5
9

Filament
Guide
LIFT
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position, remove the lid
and remove the build platform.
2. Place filament spool onto spool holder with spool being fed from
the bottom towards the back of the Dremel 3D20. Insert spool
lock into spool holder and rotate 90 degrees to lock in place.
3. Thread filament through filament guide tube.
4. Insert the filament coming from the filament guide tube into
the extruder intake (top).
5. Adhere build tape over the build platform.
6. Install the build platform using the build platform clip
to secure.
7. Plug power cord into outlet and turn on power switch.
8. Tap “Tools” on your Dremel 3D20’s touch screen, then tap
“Filament”, then tap “Load Filament” and wait for the extruder
to heat.
9. Once heated, filament will drawn through the extruder. Allow
filament to exit the extruder for 10 seconds before tapping the
return arrow to complete.
2
3
5
1
8
4
SIDE 1
PRESS COLORS
1983519835 Dremel 3D Quick Start_ENGLISH.ai
SMW 7.8.14
PMS 8402 PMS 286 PMS 151 BLACK
7. Wait for the extruder to cool before removing your object.
8. With the object still attached, remove build platform from
the build area.
9. Use your hand to peel your object from the build platform. If
needed, gently use the object removal tool to remove object
from build platform.
Best Practices & Resources
7
BEST PRACTICES
1. ALWAYS USE BUILD TAPE.
2. Ensure your build platform is level before every object.
3. Ensure spool is installed properly and can rotate freely.
4. When loading filament, allow Dremel 3D20 to extrude until
material is consistent with the installed filament color.
5. It is important to stay near your Dremel 3D20 during
operation and watch the Dremel 3D20 begin building
objects.
6. Use object removal tool gently to avoid damaging the build
platform or object.
7. Remove the build platform before removing the object.
OPERATING ENVIRONMENT
Room Temperature: 16-29° C (60 - 85° F)
Level workspace
Dry workspace environment
15.7” (400mm)
19.1” (485mm) 13.2” (335mm)
WALL
8” (203mm)
8” (203mm)8” (203mm)
14” (356mm)
3D20 RESOURCES
Quick Start Guide In box and www.dremel3d.com
3D20 Website www.dremel3d.com
3D20 Customer 1-844-4DRML3D
Support (1-844-437-6533)
www.dremel3d.com
Dremel 3D20 Installed from www.dremel3d.com
Software or from SD card provided with the
Dremel 3D20
9

SMW 7.8.14
Dremel 3D Community
8
This is for the Dremel Makers.
The ones who endlessly imagine new ideas. New projects. New missions.
Always wondering, What can I build?
How can I make it better?
More useful? More interesting? More mine.
The ones who forever fix, design, create, construct.
Building anything they want. Anything they need. Anything they’re into.
Anything their home
Or the world
Has been waiting for.
The ones who share their ideas.
Build off other people’s ideas.
And build them better.
Who believe that building a shiny new talent
is the greatest triumph of all.
The ones who, after they’ve built, allow themselves a brief moment of satisfaction
Before their hands and minds become impatient and start plotting
What to build next.
Build on, Dremel Maker. Build on.
JOIN THE COMMUNITY
1. Installing Dremel software from Dremel3D.com
2. Creating a Dremel maker profile on Dremel3D.com
3. Registering your Dremel 3D20 Idea Builder
3D20 Customer 1-844-4DRML3D
Support (1-844-437-6533)
www.dremel3d.com
Dremel 3D20 Installed from www.dremel3d.com
Software or from SD card provided with the
Dremel 3D20