Dremel DIGILAB 3D40 User manual

Spool
Holder
FIG
. 1
WARNINGWARNING
READALLOPERATING/SAFETYINSTRUCTIONS IN THE MANUAL AND FAMILIARIZEYOURSELF WITHTHE
DREMEL3D40BEFORESETUP AND USE. FAILURETO COMPLY WITHTHE WARNINGS AND INSTRUCTIONS
MAYRESULTINFIRE,EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
1-844-4DRML3D(1-844-437-6533) www.dremel.com
P.O.Box081126Racine, WI 53408-1126
3D40
IdeaBuilder
Operating/SafetyInstructions
Consignesd’utilisation/desécurité
Instruccionesdefuncionamientoy seguridad
ForEnglishVersion
Seepage2
Versionfrançaise
Voirpage16
Versiónenespañol
Verlapágina30
IMPORTANT
ReadBeforeUsing
IMPORTANT
Lireavantusage
IMPORTANTE
Leerantesdeusar
CallTollFreeforConsumerInformation& Service Locations
Pourobtenirdesinformationsetlesadressesdenoscentresdeserviceaprès-vente,appelezcenumérogratuit
Llamegratisparaobtenerinformaciónpara elconsumidor y ubicacionesde servicio
1
4
96
12
10
2
11
5
3
14 15 16 18
19
21
20
17
13
22 23 24
Model 3D40 F0133D4000
100V–240V~ 47–63Hz 1.5A Ø1.75mm (0.069")
Dremel • Mount Prospect, IL • Made in China
LISTED
3D
PRINTER
E469311
1U1
SN
A
VERTISSEMENT
ADVERTENCIA
WARNING
Toreducerisk of injury read the Operating/S afety Instructionsfor
Dremel3D40. Setupthe Dremel 3D40 in a well -ventilatedarea.
Provideatleast8 inchesof unobstructedspacingaroundDremel3D40.
Parareducir el riesgo de les iones,lealas Instruccionesde
Utilización/Seguridaddela Dremel3D40. Instale l a
Dremel3D40en uná rea bienventilada.Proporcioneporl o menos8 pulgadasdeespacio
sinobstruccionesalrededor del a 3D40.
Pourréduirele ris quede blessure, lisezle mode
d’emploietles consignesdes écuritépourl’équipement
Dremel3D40.I nstallezl’ équipementDremel3D40 dansunendroit bienventilé. Prévoyez
aumoins8po( 20 cm) d’espace sans obstructionsautourdel’équipementDremel3D40.
2625
Open
Close Filament Filament
Guide Tube
Guide Tube Filament Extruder Intake
FILAMENT LEVEL
!
!
PRESS DONE WHEN
NEW COLOR APPEARS
BACK
DONE
HOME
BACK
!
FEED FILAMENT
NEXT HOME
UNBOXING KIT CONTENTS*
1. Lid
2. Extruder
3. Z-Axis Guide Rail
4. Door
5. Gripping Handles
6. USB A Port
7. Leveling Knobs
8. Build Platform Clip
9. Touch Screen
10. Build Platform
11. Filament Spool Holder
12. Filament Spool
13. Y-Axis Guide Rail
14. Stepper motor
15. Filament Guide Tube
16. Extruder Intake
17. Extruder Fan
18. Ribbon Cable
19. X-Axis Guide Rail
20. Leveling Sensor
21. Extruder Tip
22. Power Switch
23. USB B Port
24. Ethernet Port
25. Nameplate
26. Power Input
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position.
2. Twist spool door counter-clockwise and remove.
3. Place filament spool onto spool holder with spool being fed from the bottom
towards the back of the Dremel 3D40.
4. Thread filament through filament guide tube and replace
spool door.
5. Insert the filament coming from the filament guide tube into the extruderintake.
6. Plug power cord into outlet and turn on power switch.
7. Tap “Filament” on your Dremel 3D40’s touch screen and wait for extruder to
heat.
8. When Feed Filament screen appears, tap “Next” and thread filament into
extruder intake until extruder feeds through on
its own.
9. When new filament appears from extruder tip, tap “Done” to complete filament
load process.
TIP: Save your Dremel 3D40 packaging for future transportation
and storage.
Dremel 3D40 Instruction Manual Quick Start Guide
1 Filament Spool Power Cable USB Cable
Build Tape Object Removal Tool USB Flash Drive
WARNINGWARNING
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELFWITH THE
DREMEL 3D40 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
1 2
3
4
5
6
78
9 10
11
12
13
14 15 16 17 18
19
20 21
22 23 24 25 26
WARNINGWARNING
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
INSTRUCTIONS WHEN USING THE DREMEL 3D40.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
PROPERTY DAMAGE OR PERSONAL INJURY.
5
7
9
3
8
1
2
3
4
5
ENGLISH
Unclog Tool
3D40 Quick Start Guide
1
2
3
4
5
KNOW YOUR DREMEL 3D40
21
3
4
5
6
78
9
10
11
12
13
14 15 16 17 18
19
20 21
22 23 24 25 26
FILAMENT
3 5
78
9
SIDE 1
English

FILAMENT LEVEL
!
FILAMENT LEVEL
!
!
BUILD PLATFORM IS TOO HIGH
TURN RIGHT TO LOWER HOME
BACK
!
READY TO VERIFY
HOME
BACK
VERIFY
!
BUILD PLATFORM IS TOO LOW
TURN LEFT TO RAISE HOME
BACK
!
YES
NO
USE YOUR COMPUTER OR
MOBILE DEVICE TO BUILD
FROM ANYWHERE WITH A
WIRELESS CONNECTION.
SET UP WI-FI?
HOMEBACK
!
HOMEBACK
ScrewdriverHandle...
frog.g3drem DiamondStencil.g3...
FishStencil.g3drem
!
BUILD
DELETE
COPY TO
PRINTER
FILE NAME
BUILD TIME 00:00
HOMEBACK
Part#: 2610039152
LEVELING BUILD PLATFORM
1. Tap “Level” on your Dremel 3D40’s touch screen.
2. 3D40 will first check the level at the back of the build platform, then move
to the first leveling position.
3. The touchscreen will indicate if your build platform is too high or too low.
a) If the build platform is too high, turn knob to the right until you hear a
“beep”. Tap “Verify” to check the bed
level again.
b) If the build platform is too low, turn knob to the left until you hear a
“beep”. Tap “Verify” to check the bed level again.
4. Repeat step above for the second levelling position.
5. When the build platform is level, extruder will automatically move to the
calibration position and complete the
levelling process.
BUILDING OUT OFTHE BOX
1. On the main screen, tap the “Build” option. Then tap the machine
icon to select from pre-installed models.
2. Tap on the model file you would like to build and tap “Build”.
3. Your Dremel 3D40 will align the extruderwith the build platform
and will begin heating the extruder.
4. Once the correct temperature is reached, your model will begin to
build.
5. Touch screen will display “Object Finished”.
REMOVING YOUR OBJECT FROMTHE BUILD
PLATFORM
6. Wait for the extruder to cool before removing your object.
7. With the object still attached, remove build platform from the build
area.
8. Use your hand to peel your object from the build platform. If needed,
gently use the object removal tool to remove object from build
platform.
Wi-Fi
Connect your printer to your wireless network
so you can build from anywhere.
DREMELDIGILAB.COM
Visit Dremel Digilab to sign up for the newsletter,
and receive Dremel expert customer support.
1
3
2
8
1
LEVELING
1
3
BUILDING
1
2
REGISTER
GET CONNECTED
MAKE YOUR OWN
3D40 RESOURCES
Quick Start Guide In box and www.dremeldigilab.com/GetStarted
3D40 Website www.dremeldigilab.com
3D40 Customer 1-844-4DRML3D
Support (1-844-437-6533)
Desktop Slicing Installed from www.dremeldigilab.com
Software or from USB flash drive provided
with the Dremel 3D40
More Details on 3D40 Manual in box and on www.dremeldigilab.com
Setup and Maintenance
For info on designing, slicing, and printing
your own models go to...
DremelDigiLab.com/GetStarted
BEST PRACTICES
1. ALWAYS USE BUILD TAPE.
2. Ensure your platform is level (before you begin building
your object).
3. Ensure spool is installed properly and can rotate freely.
4. When loading filament, allow Dremel 3D40 to extrude until material is
consistent with the installed filament color.
5. It is important to stay near your Dremel 3D40 during operation and watch
the Dremel 3D40 begin building objects. (If a situation occurs, select the
STOP icon right away, to stop any further building).
6. Remove the build platform before removing the object.
7. Use object removal tool gentlyto avoid damaging the build platform or
object.
FOR WARRANTY
Visit digilab.dremel.com/support to register your 3D40, to ensure proper
documentation of your 1-year warranty.
SIDE 2
English