DXV Randall D35102.940 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Randall™ Roman Tub Fillers
with Hand Shower
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013 M965563 Rev. 1.3
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Cross Handle
Model D35102.940
Lever Handle
Model D35102.900
Plumbers' Putty or Caulking
Adjustable Wrench Allen Key
Phillips Screwdriver
Channel Locks Regular Screwdriver
10 mm
1-1/4" D.
(32mm)
Ø 2-3/8"
(60mm)
10-1/4"
(260mm)
12" MAX
(305mm)
1-3/8" D.
(35mm)
NOTE: MOUNTING HOLES
ARE 1-3/8" D. (35mm) for handles
1-1/4" D. (32mm) for spout
3/4"NPT
INLETS
(19mm)
2-1/4" D.
(57mm)
8" TO 12" MAX.
(203mm TO 305mm)
5-1/2"
(140mm)
8-1/4"
(210mm)
3/4" D.
(19mm)
2-5/8" D.
(67mm) CROSS HANDLE LEVER HANDLE
1-1/2 " MAX.
(38mm) 1-1/2" MAX.
(38mm)
3
8
RECOMMENDED TOOLS AND MATERIALS
Thank you for selecting DXV by American Standard.
To ensure that your installation proceeds smoothly,
please read these instructions carefully
before you begin.
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
ROUGHING-IN DIMENSIONS:
• For reference

- 2 - M965563 Rev. 1.3
1IMPORTANT NOTICE TO THE INSTALLER!
Please check with your local Code Authority for acceptable installation
requirements for this Roman Tub set with hand shower. Some local codes
may require a vacuum breaker and/or a pressure balanced mixing valve to
be installed in conjunction with this product.
SPOUT AND T-PIECE ASSEMBLY
Turn off hot and cold water
supplies before beginning.
CAUTION
• Grease O-RING (3&11), Assemble T-PIECE (9) onto the SPOUT SHANK
and tighten with COUPLING NUT (10).
• Slide the T-PIECE (9) onto SPOUT SHANK (1) until it makes contact with
the O-RING (3). Thread COUPLING NUT (10) onto SPOUT SHANK (1).
Rotate T-PIECE (9) about 10 degrees from center and tighten securely.
Make sure both O-Rings (3 & 11) are seated into grooves of T-PIECE (9).
• Assemble RUBBER WASHER (6), FIBER WASHER (7) and LOCKNUT (8)
onto threads of SPOUT SHANK (1). Tighten rmly.
• Insert SPOUT SHANK (1) through center hole of sink or mounting surface.
Install ESCUTCHEON (4) and WASHER (5). Make sure ESCUTCHEON
snaps into PINS (2) and CUTOUT (X) shows to the back.
• T-PIECE (9) and COUPLING NUT (10) are factory pre-installed on
SPOUT SHANK (1) and must be removed to install SPOUT SHANK (1).
GROOVE
IN TEE
GROOVE IN TEE
10°
1
2
X
4
5
6
7
8
9
3
10
11
FRONT
Pins are
pre-installed in spout
HOSE ASSEMBLY
HAND SHOWER ASSEMBLY
Note: Back flow prevention and 2.5 GPM flow restrictions are
included with all Roman tub sets with hand shower
• Insert FIBER WASHERS (1) into COUPLING NUTS (2) of SUPPLY HOSES (3) and tighten.
• Drop SPRAY HOLDER (12) through ESCUTCHEON (13) and WASHER (14)
and into the fourth hole of the tub ledge (12" 305mm max from SPOUT center)
directed towards tub center. Install RUBBER WASHER (15) and
LOCKNUT (16) from underside of mounting ledge. Secure
SPRAY HOLDER (12) by tightening LOCKNUT (16).
• Install SEAL WASHER (4) and connect COUPLING NUT (5)
of BRAIDED HOSE (6) to outlet nipple. Tighten rmly.
• Slip SHOWER HOSE (10) with COUPLING NUT (9)
through SPRAY HOLDER (12) and ESCUTCHEON (14).
• Install SEAL (8) into COUPLING NUT (9). Connect
COUPLING NUT (9) to HOSE NIPPLE (7) and tighten.
• INSTALL second SEAL (4) and connect HAND
SHOWER (18) to SPRAY HOSE END (17). Hand tighten.
9
2
2
1
1
5
6
10
3
3
4
4
BRAIDED
HOSE
7
8
FRONT
13
14
11
12
18
16
17
15
3
8
2
2a

- 3 - M965563 Rev. 1.3
INSTALL VALVE BODIES
• INSTALL HANDLES (LEVER and CROSS)
1-1/2''(38mm) MAX.
• Thread LOCKNUT (8) to bottom of VALVE BODY (2). Make sure
FIBER WASHER (9) and RUBBER WASHER (10) are installed.
Insert VALVE BODY (2) through mounting hole from underside
of tub deck or mounting surface.
Note: VALVE BODY marked Hot is installed in the left Mtg.
hole, VALVE BODY marked Cold in the right when facing front
of fitting. Maximum mounting surface thickness is 1-1/2" (38mm).
• HANDLE ASSEMBLIES (1, 1A) are installed on VALVE BODIES (2)
and must be removed to install VALVE BODIES (2) from under
tub deck or mounting surface.
• To remove HANDLE ASSEMBLY (1), unthread HANDLE BASE (3)
with LEVER (4) from VALVE BODY (2). Pull HANDLE ASSEMBLY (1)
off VALVE STEM (5).
• Unthread and remove MOUNTING RING (6) and SPACER (7).
• From top install SPACER (7) onto VALVE BODY (2). Thread
MOUNTING RING (6) on VALVE BODY (2) until seated tightly against
SPACER (7). Set VALVE BODIES (2) so that their outlets are facing
toward SPOUT TEE (11) and then tighten LOCKNUT (8) using 35mm
or adjustable wrench.
• Insert FIBER WASHERS (12) into COUPLING NUTS (13) of SUPPLY HOSES (14) and tighten making water tight connection.
Important: Loop SUPPLY HOSES (14) as illustrated so they do not kink.
6
1
3
4
8
12
HOT
13
14
911
10
7
5
2
"O" RING
TUB DECK OR
MOUNTING SURFACE
Turn VALVE BODIES (2) to off position. Align HANDLES as shown or as desired and install HANDLE ASSEMBLY (1, 1A) onto
VALVE STEM (5). Thread HANDLE BASE (3) onto VALVE BODY (2) until seated tightly against mounting surface.
1A
HOT COLD
3/4" (19mm) D.
3
• Lift HAND SHOWER from HOLDER,
direct spray into tub. Lift TRANSFER KNOB to
check HAND SHOWER and HOSES for leaks.
MAKE WATER SUPPLY CONNECTIONS
• Remove AERATOR from FAUCET.
• With HANDLES in OFF position,
turn on WATER SUPPLIES and check
all connections for leaks.
• Operate both HANDLES to ush
water lines thoroughly.
• Replace AERATOR.
• Connect HOT water supply to LEFT INLET UNION (1)
and COLD water supply to RIGHT INLET UNION (2).
Pipe connections are 3/4" (19mm) NPT. Use sealant or
Teon tape on pipe connections.
Do not solder directly to valve body.
TEST INSTALLED FAUCET
3/4" X 3/4" NPT UNION
(NOT SUPPLIED) (19mm X 19mm)
HOT COLD
3/4" NPT
(19mm)
AERATOR
TRANSFER
KNOB
3/4" (19mm) NPT
(19mm)
2
1
• Turn handles "off" and replace HAND SHOWER.
IMPORTANT: It is strongly recommended
that access be provided for all enclosed
mechanical parts to this system.
3
8
HAND SHOWER
4
4a

- 4 - M965563 Rev. 1.3
Roman Tub Fillers
with Hand Shower
Randall™
D35102.940
D35102.900
MODEL NUMBERS
Lever Handle
Cross Handle
H961530.XXX
AERATOR
ASSEMBLY
H960001.191
3/4 HOT
CARTRIDGE
H961267.191
SPOUT TEE WITH DIVERTER
H960893.191
3/4 SIDE VALVE
(CLOCKWISE ON)
H960194.191
HOSE
ASSEMBLY
M964717-YYY0A
DIVERTER
ROD ASSEMBLY
A860698.XXX
DIVERTER KNOB
H960185C.191
HOSE ASSEMBLY
012668-0070A
SHANK KIT
H960440.XXX
HAND SHOWER
HOSE KIT
WITH SEALS
M964740-YYY0A
HAND SHOWER
HOLDER KIT
D35107781.XXX
HAND SPRAY
H961541.191
MOUNTING KIT
M964539-0070A
ROSETTE
A860680.XXX
CROSS HANDLE
SET
H960743.191
3/4" SIDE VALVE
ROUGH
(COUNTER
CLOCKWISE ON)
H960294.191
MOUNTING KIT
H960170.191
3/4" CARTRIDGE
(CLOCKWISE ON)
A860681.XXX
LEVER HANDLE
SET
100
144
150
Replace the "XXX" or "YYY" with
appropriate nish code
POLISHED CHROME
BRUSHED NICKEL
PLATINUM NICKEL
M964543-YYY0A
SET SCREW KIT