DXV Keefe D35104500 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965478 Rev. 1.6 (5/17)
Model D35104500
To be used with D35000500.191
Pressure Balanced Shower Valve
Keefe®
Pressure Balance
Shower Valve Trim Kit
Phillips Screwdriver Flat Blade Screwdriver
H
O
T
C
O
L
D
O
F
F
ROUGHING-IN DIMENSIONS:
• For reference
FINISHED WALL
BOTTOM OF
TUB
OR SHOWER
STALL
(1219 mm to
1372 mm)
SHW
TUB
8" sq.
(203 mm)
48" TO 54"
OPTIONAL
1/2" NPT
1-5/8" TO 3-1/4"
(41 mm to 83 mm)
OPTIONAL TO
FINISHED FLOOR
USUALLY
BETWEEN
72'' AND 84"
(1828 mm to 2133 mm)
74" FOR HEAD
CLEARANCE
(OPTIONAL)
(1880 mm)
BOTTOM OF
SHOWER HEAD
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

- 2 -
GREASE
O-RING
9
1
10
11
7
5
4
13
2
3
86
H
O
T
C
O
L
D
O
F
F
12
M965478 Rev. 1.6 (5/17)
1
2ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, all you need to do
is adjust the setting on the HOT LIMIT SAFETY STOP (1).
• Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Use a
at blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull forward and rotate counterclockwise one number to
limit hot water temperature. Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1) for indication.
• Push CAP (4) over VALVE CARTRIDGE (13) until seated against stop.
• Mount ESCUTCHEON HOLDER (1) with gasket to tting using two LONG SCREWS (2).
Push the ESCUTCHEON COVER (3) over CAP (4). Align screw holes in ESCUTCHEON COVER (3)
with holes in ESCUTCHEON HOLDER (1). Fasten with three MOUNTING SCREWS (5).
• Push ADAPTER (6) onto CARTRIDGE STEM (7) and secure with WASHER and SCREW (8).
• Push DIAL PLATE (9) onto CAP (4) ush against ESCUTCHEON COVER (3)
with the “OFF” facing down.
• Install HANDLE ASSEMBLY (10) onto ADAPTER (6)
with LEVER (11) in the down position. Turn LEVER (11)
clockwise to off position. Pull HANDLE ASSEMBLY (10)
off and align again to down position.
Thread HANDLE BASE (12) clockwise onto
ADAPTER (6) to secure handle to valve.
INSTALL TRIM
CAUTION Protect finish on SHOWER ARM and
SHOWER HEAD when installing.
1
5
1
3
1
1
9
7
5
3
1
0
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
1
5
1
5
44
3
3
22

- 3 - M965478 Rev. 1.6 (5/17)
3TEST INSTALLED FITTING
• Turn VALVE “off”.
• With HANDLE (1) in “off” position, turn on water supplies
and check all connections for leaks.
• Operate HANDLE and ush water lines thoroughly.
Check the function for proper operation.
1
H
O
T
C
O
L
D
O
F
F
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
MODEL NUMBERS
D35104500
Keefe®
Pressure Balanced
Shower Valve Trim Kit
M964516-YYY0A
HANDLE KIT
M964523-0070A
SCREWS
M964519-YYY0A
COVER
M964526-0070A
ESCUTCHEON
HOLDER KIT
H960685.XXX
TRIM PLATE SCREWS
M964522-YYY0A
TRIM PLATE
M964517-0070A
ADAPTER AND
SCREW KIT
H
O
T
C
O
L
D
O
F
F
H961229.XXX
TRIM RING
A3195.191
EXTENSION KIT
(CARTRIDGE)
A3196.191
EXTENSION KIT
(DIVERTER)