DXV Fitzgerald D35160802 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965911 (8/18)
Model D35160802
Fitzgerald®
Widespread
Lavatory Faucet
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or Caulking
Phillips Screwdriver
Channel Locks
Flat Blade Screwdriver
Adjustable Wrench
Basin Wrench
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
FLEXIBLE
HOSE
FLEXIBLE
HOSE
1-1/4" MAX.
(32 mm)
1-1/16" DIA.
(29 mm)
1-1/2" MAX.
(38 mm)
6" to 12"
(152 to 305 mm)
FLEXIBLE
ø2-5/8" .
(67 mm)
8" (203 mm)
14-3/4"
(374 mm)
3-1/16"
(78 mm)
4-3/8"
(112 mm)
4-5/8"
(118 mm)
3-3/8"
(85 mm)
5"
(127 mm)
7" (178 mm)
5-3/16" (132 mm)
2-3/4"
(69 mm)
8-5/8"
(220 mm)
1-1/4" O.D.
(32 mm)

- 2 - M965911 (8/18)
1INSTALL SPOUT CAUTION Turn off hot and cold water
supplies before begining.
1A INSTALL VALVE BODIES
Fig. A.
• Insert SHANK (1) and HOSE (2) through center hole.
• Thread LOCKNUT (3) onto SHANK (1) from underside of sink or
mounting surface.
• Align and center SPOUT (4). Tighten LOCKNUT (3).
Fig. B.
• Insert Hot and Cold SIDE VALVE HOSES (7),
FLEXIBLE SUPPLIES (7a) into mounting holes.
• Thread LOCKNUT (6) onto each SIDE VALVE
SHANK (5) from underside of sink or
mounting surface.
• Align and center SIDE VALVES. Tighten
LOCKNUTS (6).
• Thread HANDLE (8) to SIDE DECK ADAPTOR (9).
SPOUT BASE
4
Fig. A.
Fig. B.
1
7Blue Stripe (COLD)
7Red Stripe
(HOT)
7a
7a
5
6
8
9
3
2

- 3 - M965911 (8/18)
4 5
FLANGE GASKET AND POP-UP KNOB CHECK OPERATION OF POP-UP
• Check DRAIN FLANGE in SINK to ensure that
FOAM GASKET (3) is fully compressed and not visible.
FOAM
GASKET
NOT VISIBLE DRAIN
FLANGE
2 3
INSTALL DRAIN FROM BELOW FIXTURE
• Install DRAIN (1) by dropping it from the top of the sink.
• From under side of SINK install GASKET (2) and
MOUNTING NUT (3).
Note: Plumber’s putty or caulk is recommended.
• Thread TAIL PIECE NUT (1) clockwise onto
DRAIN BODY (2).
DRAIN
OUTLET
REAR OF SINK
1
2
3
1
2
1
• Operate DRAIN STOPPER (1) to verify that it opens
and closes.
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3).
• Operate HANDLE (1) to ush water lines thoroughly.
• Replace AERATOR (3).
CHECK DRAIN CONNECTIONS
• Fill lavatory with water. Check that DRAIN STOPPER (4)
makes a good seal and retains water in SINK.
• Release DRAIN STOPPER (4) down and check all drain
connections and “P” trap for leaks. Tighten if necessary.
TEST INSTALLED FITTING
6
2
3
2
1
1
4
“P” TRAP
WAST E
OUTLET

- 4 - M965911 (8/18)
11
MODEL NUMBER
Fitzgerald®
Widespread
Lavatory Faucets
M953456-YYY0A
DRAIN ASSEMBLY
M970532-0070A
DECK ADAPTER
M970531-YYY0A
HANDLE KIT
M923840-0070A
AERATOR KIT
(1.2 GPM)
M964055-0070A
HANDLE ADAPTER KIT
M964005-0070A
CARTIRIDGE KIT
A911897-0070A
SEAL
M911116-0070A
SPACER
M906617-0070A
VALVE MOUNTING NUT
M964224-0070A
MOUNTING KIT
M904516-0070A
T-CONNECTOR
D35160802
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
PLATINUM NICKEL 150