DXV Lyndon D25005001.415 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017 7302269-100 Rev. 1.0 (5/17)
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work has begun.
ROUGHING-IN DIMENSIONS: If a side by side toilet and bidet installation is desired, a comfortable separation
of 2 feet (610 mm) is required between the units.
Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
ALL INSTALLATION PROCEDURES MUST COMPLY IN STRICT ACCORDANCE WITH APPLICABLE
LOCAL PLUMBING AND BUILDING CODES
!
Lyndon™
Floor Standing Bidet
Model D25005001.415
Adjustable Wrench
Regular Screwdriver
10'
Level
Flexible Supply Tube
Closet Bolts
Putty Knife
Tape Measure Hacksaw
Sealant
1-3/8"
35 mm
20-1/2"
520 mm
1-13/16"
46 mm
2-3/4"
70 mm
14-3/16"
360 mm
2-3/8"
60 mm
8-1/4"
210 mm
20-1/2"
520 mm
16-3/8"
415 mm
2-3/8"
60 mm
6-1/5"
165 mm
1/2"
12 mm 1-3/8"
35 mm
8-1/4"
210 mm
17-5/16"
440 mm
10-1/4"
260 mm
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx

- 2 -
1
2
3
CONSOLE STAND INSTALLATION
REPLACEMENT USE:
Typical bidet installation includes: wall preparation; installation of hot and cold water supply lines and shutoff valves;
installation of bidet tting; installation of P-trap drain connection; mounting bidet to ooring; and connection to house
water supply and drain.
Bidet Mounting Provisions – Bidets are usually installed adjacent to a toilet; if this is done, ensure at least 18"(45.7 cm)
oor space be provided between xtures. Bidets use a pop-up drain, requires a P-trap drain hookup, (a true 1-1/4"(32 mm)
bodied “P”-trap, do not use a universal 1-1/4"x 1-1/2"(32 x 38 mm) trap), and is supplied both hot and cold water. Bidets
are attached directly to ooring with two lag screws at base mounting holes. Also note when installing the Estate bidet a
specic facuet is required.
When replacing an original unit be sure to shut off water supply before removing the unit or disconnecting water supply
lines and drain ttings. Original supply lines and shutoff valves should be replaced and used with ttings and adapters
to match the hookups on the replacement unit.
USE TEFLON SEALANT TAPE ON PIPE THREADS FOR WATERTIGHT CONNECTIONS!
Refer to bidet illustrations. Measure the distance from the nished wall to the center of the drain outlet corresponding to
selected bidet model dimension. Check that the distance between the nished wall to the end of the bidet is compatible
with clearance requirements of your bidet tting.
Provisions must be made for the installation of a "P" trap in the oor when drain outlet is installed.
It is suggested that the water supplies should be located near the center line of the bidet, approximately 3" (76 mm) to either
side. Wall supply installations must be approximately 7" (178 mm) above the oor and protrude a minimum of 3-1/4" (83 mm)
from the wall. Complete rough-in using angle 3/8" (10 mm) stop valves. If oor supply installation is desired, check dimensions
from nished wall to end of the bidet and rough-in appropriately. Use straight stop valves.
It is recommended that you install the bidet tting and drain assembly at this time to ease installation.
• Mount bidet to oor using supplied hardware.
• Mark oor locations for installation of Lag Screws
and mounting brackets. Ensure mounting holes on
side of bidet are in line with marked area on oor. (ref diag. a)
• Drill a pilot hole at marked locations for wall anchor
and install anchor.
• Install lag screws, washers into slots of each bracket,
then into anchor. Loosely tighten lag screws but
ensure plastic brackets can still move with little resistance.
• Carefully place bidet over mounting area which will
also contact and slightly move the plastic brackets
into better position.
• Remove the bidet and nish tightening the lag screws.
• Place bidet back into position, now using smaller screws
and plastic inserts through the hole on the side of bidet
and into the plastic bracket. Slightly tighten screws to
anchor bidet to oor.
7302269-100 Rev. 1.0 (5/17)
4
5
4"
103 mm
4"
103 mm
8-1/4"
210 mm
SUMINISTRADO PIEZAS