DXV Ashbee D3510184C User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work has begun.
M965703 1.0 (5/17)
Cross Handle
Model D3510184C
Lever Handle
Model D3510180C
Ashbee™
Widespread Lavatory Faucets
Plumbers' Putty or Caulking Adjustable WrenchPhillips Screwdriver
Channel Locks
Tubing Cutter
Flat Blade Screwdriver
Basin Wrench
ROUGHING-IN DIMENSIONS:
• For reference
1-1/4" MAX.
(32 mm)
1-1/16" DIA.
(27 mm)
1-1/4" O.D.
(32 mm)
2-3/4" DIA.
(70 mm) 3-1/8"
(78 mm)
6" TO 12" MAX.
(152 to 305 mm)
3-5/8"
(92 mm)
3-1/2"
(90 mm)
1-1/2" MAX.
(38 mm)
2" MAX.
(51 mm)
6-1/8"
(150 mm)
5-1/8"
(130 mm)
3"
(70 mm)
2-1/8" DIA.
(54 mm)
7-1/2" MAX.
(191 mm)
7/8" DIA.
(22 mm)
CROSS
HANDLE
STRAIGHT
LEVER
HANDLE
NOTE: MOUNTING HOLES ARE 1-3/8" DIA. (35 mm)
CONNECTIONS:
• 1/2" IPS FLEXIBLE SUPPLIES
• 3/8" O.D. BULL-NOSE RISERS
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

- 2 - M965703 1.0 (5/17)
1 2
3HOSE ASSEMBLY
• If HANDLES (1 & 2) and HANDLE BASE (3) are installed on
VALVE BODIES (4) they must be removed to install VALVE BODIES (4)
from under lavatory or mounting surface.
• To remove CROSS HANDLE (1); Pull-out INDEX CAP (5) and
remove HANDLE SCREW (6). Pull off CROSS HANDLE (1) and
unthread HANDLE BASE (3).
• To remove LEVER HANDLES (2); loosen SET SCREW (7) with
Hex Wrench provided with faucet. Pull LEVER HANDLE (2) off and
unthread HANDLE BASE (3).
• Thread LOCKNUT (8) to bottom of VALVE BODY (4). Make sure FIBER
WASHER (9) and RUBBER WASHER (10) are installed. Insert VALVE BODY (4)
through mounting hole from underside of SINK or mounting surface.
Note: Maximum mounting thickness is 1-1/4" (32 mm)
• Thread LOCKNUT (8) to bottom of VALVE BODY (4). Make sure
FIBER WASHER (9) and RUBBER WASHER (10) are installed.
Insert VALVE BODY (4) through mounting hole from underside of
SINK or mounting surface.
• Thread HANDLE BASE (3) until snug against internal stop. Set VALVE
BODIES (4) so that their outlets are facing toward SPOUT TEE (11) and
then tighten LOCKNUT (8) using wrench.
• Tighten COUPLING NUT (12) on SUPPLY HOSE (14) to OUTLET (13) making water tight connection.
Important: Loop SUPPLY HOSES (14) as shown so they do not kink.
INSTALL HANDLES
• FOR LEVER HANDLES: Install FRICTION WASHER (15) onto base of LEVER HANDLE (2). With VALVE in off position
align LEVER HANDLE (2) as shown. Install LEVER HANDLE (2) onto VALVE STEM (16) and tighten SET SCREW (7) with
HEX WRENCH supplied.
• FOR CROSS HANDLES: With VALVE in off position align CROSS HANDLE (1) as shown. Install CROSS HANDLE (1) onto
VALVE STEM (16) and tighten HANDLE SCREW (6). Insert HOT INDEX (5) into left CROSS HANDLE and COLD INDEX (17)
into right CROSS HANDLE.
• Insert SPOUT SHANK (1) through
center hole of sink or mounting
surface. Make sure RUBBER
WASHER (2) is seated into groove
in SPOUT ESCUTCHEON BASE (3).
• Assemble RUBBER WASHER (4),
BRASS WASHER (5) and
LOCKNUT (6) onto threads of SPOUT
SHANK (1) from underside of lavatory
or mounting surface.
• Align SPOUT (7) and tighten
LOCKNUT (6). Insert LIFT ROD (8)
through SPOUT (7).
SPOUT ASSEMBLY TEE ASSEMBLY
CAUTION Turn off hot and cold water
supplies before beginning.
• Thread TEE BODY (1) COUPLING NUT (2)
to SPOUT SHANK (3).
1
2
3
7
8
GROOVE
4
6
51
3
2
5
6
1
3
2
8
4
1213
14
911
10
7
HEX WENCH,
SUPPLIED
15
COLD
HOT
1-1/4'' MAX.

- 3 - M965703 1.0 (5/17)
4
5
6
WATER SUPPLY CONNECTIONS
MAKE WATER SUPPLY CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS
MUST BE PURCHASED SEPARATELY.
• Connect water supply to VALVE BODIES (1) with 1/2" (13 mm) IPS
FLEXIBLE SUPPLIES (3) or 3/8" (10 mm) O.D. BULL-NOSE RISERS (4).
Use wrench to tighten connections.
• Do not over tighten. Be careful not to kink copper supply when
bending. Use tubing cutter to cut to proper length.
• Remove AERATOR (3) from faucet.
• With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2)
and check all connections for leaks.
Operate both HANDLES to ush water lines thoroughly.
• Operate Lift Rod (5) and ll lavatory with water. Check that DRAIN
STOPPER (4) makes a good seal and retains water in lavatory.
Adjust stopper height by repositioning Lift Rod (5) and
tightening SET SCREW (6).
• Release DRAIN STOPPER (4) and check all drain connections and
“P” trap for leaks. Tighten if necessary.
• Replace AERATOR (3).
INSTALL POP-UP DRAIN
FIG. 4a
• A FOAM SEAL (1) is installed on underside of FLANGE (2).
(Plumbers Putty may be used in place of FOAM SEAL (1) if desired.)
• Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6)
onto DRAIN FLANGE (2). Do not tighten fully.
FIG. 4b
• Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
• The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
• Apply sealant or Teon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
FIG. 4c
• Assemble PIVOT ROD (11), WASHER (20) and PIVOT NUT (12) as shown.
Install CONCAVE WASHER (19) into PIVOT ROD OPENING (9) if not
reinstalled. Hand tighten PIVOT NUT (12). Drop STOPPER (13) into drain.
(To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13). Make connection to “P” TRAP.
• Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten. Drop
POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and tighten SET SCREW (17).
• Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15) and tightening SET SCREW (18).
APPLY SEALANT
OR TEFLON TAPE
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
10
9
7
6
12
19
16
1517
18 2
10
14
13
11
20
3
1
4
FERRULE
COUPLING NUT
2
2
1
4
5
6
3

- 4 - M965703 1.0 (5/17)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
PLATINUM NICKEL 150
MODEL NUMBERS
Cross Handle
D3510184C
Lever Handle
D3510180C
Ashbee™
Widespread
Lavatory Faucets
H960019.XXX
STRAIGHT LEVER
M964573-YYY0A
AERATOR
H960358.XXX
HANDLE BASE
H960141.XXX
ROSETTE
H960750.XXX
POP-UP ROD
H960742.191
1/2" SIDE
VALVE ROUGH
(CLOCK-WISE ON)
H960279.191
MOUNTING KIT
H960295.191
SPOUT
MOUNTING KIT
H960104.191
1/2
" HOT CARTRIDGE
H960741.191
1/2" SIDE
VALVE ROUGH
(CLOCK-WISE ON)
M953006-0070A
TEE & HOSE
ASSEMBLY
H960758.XXX
CROSS HANDLE
SET (HOT)
H960551.XXX
HANDLE CAP (HOT)
H960526.XXX
HANDLE CAP (COLD)
H960759.XXX
CROSS HANDLE
SET (COLD)
H960136.191
1/2" COLD
CARTRIDGE
874014.XXX
DRAIN ASSEMBLY
H960752.XXX
POP-UP KNOB
M964511-YYY0A
TAPERED
CONNECTOR
H960752.XXX