EAST COAST Nebraska Wardrobe User guide

Nebraska Wardrobe
Assembly and care
instructions

IMPORTANT!
READ CAREFULLY AND KEEP FOR
FUTURE REFERENCE
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
1
Hardware
A x 12
M x 6
B x 8 C x 54
(Short)
D x 5
(Medium)
E x 4
(Long)
F x 4 G x 4 H x 4
Hexagon key
I x 4 J x 4 K x 1 L x 1

2
Wooden Parts
Back panels
x 2
Sides (L+R)
Top shelf
Bottom shelf
Doors x 2
Panel joiner
Hanging rails
x2
Drawer sides
(L+R)
Drawer base
Drawer back
Drawer front
Drawer
support

3
Assembly 1
Assembly 2
Side (R)
A x 3
B x 2
Note: Repeat
assembly 1 + 2 for
other side (L).
Bottom shelf
A x 3
B x 2
Top shelf

4
Assembly 3
Assembly 4
Back panels
C x 8
C x 13
C x 13
Panel joiner
G x 4
Hanging rail
Note: Repeat for
other hanging rail

5
Assembly 5
Assembly 6
Drawer front
J x 2
I x 2
D x 2
D x 2
Drawer side (R)
Drawer side (L)
K x 1
L x 1
Drawer support

6
Assembly 7
E x 2
E x 2
F x 2
Drawer back
Drawer base
D x 1
F x 2
Assembly 8
Door
C x 6
I x 1
M x 3
J x 1
C x 2
H x 1
C x 2
H x 1

7
Assembly 9
1. Loosen screws on all hinge parts.
2. Slide hooks on hinge (i) under hinge plate (ii).
3. Click end of hinge (iii) onto clip at back of hinge plate (iv). Note: some force may be needed to click
the two parts together.
4. Before tightening screws on hinge plate (v), lift door and tighten rear screws on hinge plate (v) first.
Note: Keep holding door in highest position until screws fully tightened.
5. Tighten remaining front screws. Note: Do not over tighten.
i
Note: Repeat assembly 5 + 6 for
other door.
ii
iii
iv
v
Note: Fitting doors can be easier
with another person

Assembly 10
NOTE:
To adjust the fit of the doors in the frame, position the wardrobe where it will be used and use screws 1
and 2:
Screw 1 loosens the hinge to move the door forward or backward.
Screw 2 moves the door closer to, or further from the frame.
Screw 1
Screw 2
Screw 1
Screw 2
8

Assembly 11
HINT: If wardrobe is to be used on floor that is uneven, doors could appear not to sit in the frame
correctly. Packing could be placed under either the left or right rear feet to help level the wardrobe and
improve the look of the doors.
9

10
Assembly 12
The wardrobe is supplied with a fixing kit which will secure it and help to guard against accidental
tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
Washer x 2 Screw (short) Screw (long)
Plastic wall plug
(for brick and masonry wall
use only)
Fabric strap
1. Place the wardrobe against the wall where it is to be fitted and mark the wall through the slot in the
back.
2. Move the wardrobe away and using the long screw, washer and the appropriate wall fixing attach the
fabric strap to the marked position.
3. Attach the fabric strap to the top of the wardrobe using the short screw and washer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
The type of wall fixing you will require depends on the construction of the wall.
See below for details. If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away the
core structure.
Cavity wall: Special toggle wall
plugs needed. Seek expert
advice.
Brick or masonry: Use the wall
plug, provided you are sure that
your wall is sound.
1 2 4
The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place dresser against the wall where it is to be fitted. Mark the wall 25mm (1”) down from the top surface
of the changer.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked
position.
3. Remove the top drawer and thread the free end of the strap through the slot in the back panel.
4. From the inside of the dresser, attach the fabric strap to the dresser frame using the 15mm screw and the
washer.
Refit the top drawer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1
234
The type of wall fixing you will require depends on the construction of the wall. See below for details.
If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away
the core structure.
Brick or masonry: Use
the wall plug, provided
you are sure that your
wall is sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
Washer x 2
Fabric strap
Plastic wall plug
(For brick or masonry wall use only)
Screw (25mm)Screw (15mm)
9
Assembly 11
1

East Coast Nursery Ltd, Robertson House
North Walsham, Norfolk, NR28 0BX, UK
For customer care or enquiries:
Call: [phone]
Email: [e-mail]
eastcoastnursery.co.uk EC_NBWD_270919
Care and maintenance
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
In use
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the wardrobe.
Do not use if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
Only use the wardrobe on a stable and level surface.
Ensure that the wall strap is used to securely attach the wardrobe to the wall to prevent tipping.