EAST COAST Toulouse Wardrobe Grey User guide

Toulouse Wardrobe
Grey
Assembly and care
instructions

Hardware
G x 9
(long)
B x 14
(medium)
E x 14
J x 2
A x 4
(long)
C x 15
(short)
L x 6
D x 32
H x 12
(medium)
F x 6
Hexagon Key x 1
I x 76
(short)
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
IMPORTANT
RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
K x 2
2

Wooden Parts
Centre rear crossbar
Plain crossbar (wide) x 2
Clothes rail x 2
Front crossbar
Plain crossbar (narrow) x 2
Wardrobe side x 2 (L & R)
Trim panel
Door x 2
Drawer brace
Top panel
Drawer back
Drawer base
Shelf
Drawer front
Drawer side x 2 (L & R)
Rear crossbar (with holes) x 2
Back panel (large) x 2
Back panel (small) x 2
3

Assembly 1
Assembly 2
E
B
Front crossbar
Plain crossbar (wide)
Plain crossbar (narrow)
Rear crossbar (with holes)
Centre rear crossbar
Plain Crossbar (Narrow)
Plain crossbar (wide)
Wardrobe side
NOTE: Take care to insert the dowels
into the correct holes as indicated.
Repeat for the opposite end of each
part. (Total 32 x part D)
D x 16
Front crossbar
Centre rear crossbar
Plain crossbar (wide) x 2
Plain crossbar (narrow) x 2
7 locations
Rear crossbar (with holes)
Rear crossbar (with holes) x 2
NOTE:
Fit "Rear crossbar (with holes)" and
"Plain crossbar (narrow)" with the larger
recessed hole toward the feet of the wardrobe.
4

Shelf
7 locations
B
E
C x 6
Assembly 4
Assembly 3
A x 2
Wardrobe side
5

C x 3
Trim panel
Top panel
C x 6
Top panel
A x 2
Assembly 5
Assembly 6
6

NOTE:
This stage is best carried out with the wardrobe laid on
its front on a soft surface.
1. Place each Back panel into the recess on the
back of the wardrobe in the positions shown in
the diagram.
2. Secure each Back panel in place with screws I.
I x 76
Back panel (large)
Assembly 7
Back panel (large)
Back panel (small)
Back panel (small)
7

Assembly 9
Assembly 8
Assembly 10
G x 4
Drawer side
Drawer side
Drawer front
Drawer base
Drawer brace
Drawer back
8

Assembly 11
Assembly 12
Completed Drawer
F x 4
G x 5
J x 2
Clothes rail
Clothes rail
9

Assembly 13
The wardrobe is supplied with a fixing kit which will secure it and help to guard against accidental
tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place the wardrobe against the wall where it is to be fitted. Mark the wall at the centre of the top edge
of the wardrobe. Move the wardrobe away.
2. Using the 25mm screw, washer and the appropriate wall fixing, attach the fabric strap to the marked
position.
3. Re-position the wardrobe. Attach the strap to the top of the wardrobe using the 15mm screw and the
washer.
4. Proceed to Assembly 14 to fit and adjust the doors.
Before use, ensure that the strap is securely fixed to both the wall and the wardrobe.
Washer x 2
Screw (short)
Screw (long)
Plastic wall plug
(for brick and masonry wall use
only)
Fabric strap
1
2
3
The type of wall fixing you will require depends on the construction of the wall. See below for details. If in
doubt, seek professional advice:
Wood: If fixing to wood
make sure that it isn’t
chipboard as screws can
easily pull away the core
structure.
Brick or masonry: Use the
wall plug, provided you are
sure that your wall is
sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
10

Assembly 14
Assembly 15
K x 1
F x 1
H x 2
(6 total)
L (3 total)
Door
NOTE:
Repeat for second door.
Screw 1
Screw 2
NOTE:
To adjust the fit of the doors in the frame, position
the wardrobe where it will be used and use screws 1
and 2:
Screw 1 loosens the hinge to move the door forward
or backward.
Screw 2 moves the door closer to, or further from
the frame.
1.
2.
11

EC_TWDG_300119
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the wardrobe.
Do not use if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
Only use the wardrobe on a stable and level surface.
Ensure that the wall strap is used to securely attach the wardrobe to the wall to prevent tipping.