EAST COAST Kensington Sleigh Dresser User manual

Kensington Sleigh Dresser
Instructions
IMPORTANT! RETAIN FOR FUTURE
REFERENCE. READ CAREFULLY

Page 1
1 Welcome
2 Safety notes
•WARNING: Do not leave your child unattended.
•WARNING: Any mat used with this changing unit should not compromise the
effective height of the side barriers.
•Keep children clear during assembly as pack contains small parts which may
present a choking hazard.
•All assembly xings should always be correctly tightened and checked regularly.
•Be aware of the risk of open res and other such sources of strong heat, such as
electric bar res, gas res, etc in the vicinity of the dresser.
•Do not use the dresser if any part is broken, torn or missing.
•Replacement parts should only be obtained from the retailer. Others may render
the dresser unsafe.
•Once assembled, it is inadvisable to take the dresser apart.
•Designed and manufactured to BS EN 12221 : 2008. + A1:2013.
The dresser is carefully designed for your baby's safety and features two shelves
and a drawer for storage of baby's essentials.
The changing surface is suitable for children up to 12 months old or 11 kg in
weight, and should be used with a changing mat, available separately, of up to
74 cm x 46 cm.
To ensure safe, trouble free use, please take a little time to read the important
safety notes below and the following instructions.

Page 2
3 Parts list
Please retain all packaging until you are certain no parts are missing.
In the case of assembly difficulties, missing parts or other queries, please contact
the customer care hotline for this product on 01692 408802.
After assembly, please dispose of all packaging carefully.
Medium cross-point and at bladed screwdrivers are required for assembly.
The help of an assistant will make assembly easier.
30mm wooden dowel x 16
Camlock nut x 12
Camlock pin x 12
24mm screw x 2
35mm woodscrew x 12
Drawer front
Drawer base
Drawer side x 2
Side frame
lower bars x 2
Front frame
Back frame
Drawer back
6mm Shelf x 3
Side frame 1
Side frame 2
Handle x 2

Screw camlock pins into the holes indicated below in the back and front frames.
Page 3
4 Dresser assembly
Attach the lower bars to the side frames using two 35mm woodscrews.
Push six 30mm dowels into the holes in each side frame and two into each lower
bar as shown below. Ensure the dowels are pushed fully in.
30mm
35mm
30mm

Page 4
5 Dresser assembly
Drawer runner
Attach the side frames to the back panel and insert camlock nuts into the large
holes in each side frame. Ensure that the screwdriver slot is visible and the arrow on
the nut points to the nearest panel edge.
Secure by turning the camlock nuts approximately 1/2 a turn until  rm resistance is
felt. Repeat step for second side panel.
NOTE: Ensure that the side frames are attached with the drawer runners towards
the front edge of the dresser.
6 Dresser assembly
Slide the 3 shelves into the grooves in the back panel.
Attach the front panel to the side frames and secure by tightening the camlock
nuts as described in the previous stage.

Page 5
7 Drawer assembly and installation
Attach the drawer sides to the back using two 35mm woodscrews in each side.
Slide the base into the slots in the sides and back, then attach the drawer front
using two 35mm woodscrews in each side.
To fit the completed drawer into the dresser, tilt the drawer backwards, locate the
rollers into the tracks on the dresser side frames and push the drawer in.
Attach the handles to the drawer front using the 24mm screws.
35mm
35mm
24mm

8 Safety strap
The dresser is supplied with a fixing kit which will secure it and help to guard
against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place dresser against the wall where it is to be fitted. Mark the wall 25mm (1”)
down from the changing surface of the dresser.
2. Using the 25mm screw, a washer and the appropriate wall fixing attach the
fabric strap in the marked position.
3. Thread the free end of the strap through the slot in the back panel.
4. From the inside of the dresser, attach the fabric strap to the front face of the
upper crossbar using the 15mm screw and remaining washer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1 2 3 4
Washer x 2
Fabric strap
Plastic wall plug
(For brick or masonry wall use only)
Screw (25mm)Screw (15mm)
Page 6

9 Furniture stability
WARNING!
IN ORDER TO PREVENT OVERTURNING, THIS PRODUCT MUST BE USED WITH THE WALL
ATTACHMENT DEVICE PROVIDED.
Serious or fatal crushing injuries can occur from furniture tipping over. To help prevent
topple over, please observe the following:
1. Use the wall attachment device provided.
2. Never allow children to climb or hang on drawers, doors or shelves.
3. Place heaviest items in the lower drawers or shelves.
4. Unless specically designed to accommodate, do not set TV’s or other heavy
objects on top of this product.
5. Never open more than one drawer at a time.
An attachment device is provided with your product; however, you will need to
source suitable xings for your wall type. If in doubt, please consult a qualied
tradesperson.
Always ensure the wall to be drilled is free from hidden electrical wires, water and
gas pipes.
10 Care of your product
Regularly check the tightness of xings and tighten as necessary.
Check for damage which could render your dresser unsafe or cause splinters.
To clean, use a damp cloth, avoiding the use of strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the appearance.
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk