EAST COAST Toulouse Dresser White User guide

Toulouse Dresser
White
Assembly and care
instructions

IMPORTANT!
READ CAREFULLY AND KEEP FOR
FUTURE REFERENCE
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
1
Hardware
A x 16
(long)
J x 6 Hexagon Key
C x 48B x 13
(short)
D x 5 F x 14E x 5
H x 28
(short)
G x 27
(long)
I x 12

2
Wooden Parts
Changer side 1 Changer divider 2
Changer divider 1 Changer rear
Changer side 2
Changer front
Dresser top
Twin drawer front
Side panel x 2 (L & R)
Single drawer front x 2
Upper back panel
Upper front crossbar
Front crossbar
Plain crossbar x 4
Upper rear crossbar
Lower back panel
Drawer back x 3
Drawer side x 6 (L & R)
Drawer base x 3
Drawer brace x 3

3
Assembly 1
Assembly 2
NOTE: Take care to insert the dowels into the correct
holes as indicated. Repeat for the opposite end of
each crossbar. (Total 28 x part C)
Plain crossbar x 4
Upper rear crossbar
Upper front crossbar
Front crossbar
C x 14
NOTE: Secure all Crossbars using Parts A and F
(1 each per Crossbar) as shown.
Side panel
Upper front crossbar
Plain crossbar
Upper rear crossbar
Front crossbar
Plain crossbar
Plain crossbar
Plain crossbar
A
F

4
Assembly 3
Assembly 4
NOTE: Secure all Crossbars using Parts A and F
(1 each per Crossbar) as shown.
Side panel
Changer front
Changer divider 1
Changer side 2
D x 5
A
F

5
Assembly 5
Assembly 6
Assembly 7
C x 8
Changer divider 1
Changer side 2
Changer side 1
Changer divider 2 C x 8
Changer divider 1
Changer divider 2
E x 2
Changer side 1
Changer side 2
Dresser top
B x 2

6
Assembly 8
Assembly 9
Changer front
Changer rear
E x 3
B x 5

7
Assembly 10
Assembly 11
C x 4
NOTE:
Ensure the Dresser
Top is assembled
as shown.
Changer front
Dresser top
B x 3
A x 2
B x 3
Front crossbar

8
Assembly 12
Assembly 13
Assembly 14
Drawer side
G x 2
Lower Back Panel
Twin drawer front
NOTE: Repeat for remaining drawers.
Drawer base
Upper Back Panel (slot at top)
H x 14
H x 14
Drawer side
NOTE: Repeat for remaining drawers.
G x 2

9
Assembly 15
Assembly 16
Assembly 17
Drawer back
Drawer brace
NOTE: Repeat for remaining drawers.
J x 2
G x 3
G x 2 I x 4
NOTE: Repeat for remaining drawers.
Twin drawer front
Single drawer front
Single drawer front

10
Assembly 18
The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
Washer x 2 Screw (short) Screw (long)
Plastic wall plug
(for brick and masonry wall
use only)
Fabric strap
1. Place the dresser against the wall where it is to be fitted. Remove the top drawer and mark the wall
through the slot in the Upper Back Panel.
2. Move the dresser away and using the long screw, washer and the appropriate wall fixing attach the
fabric strap to the marked position.
3. Replace the dresser and thread the fabric strap through the slot in the Upper Back Panel.
4. Attach the fabric strap to the Upper Rear Crossbar using the short screw and the washer.
5. Replace the top drawer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1 2 4
The type of wall fixing you will require depends on the construction of the wall.
See below for details. If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away the
core structure.
Cavity wall: Special toggle wall
plugs needed. Seek expert
advice.
Brick or masonry: Use the wall
plug, provided you are sure that
your wall is sound.

East Coast Nursery Ltd, Robertson House
North Walsham, Norfolk, NR28 0BX, UK
For customer care or enquiries:
Call: [phone]
Email: [e-mail]
eastcoastnursery.co.uk EC_TDRW_150219
Care and maintenance
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
In use
Warning: Do not leave your child unattended.
Ensure that all fittings are tightened properly. Loose screws could allow a child to trap part of their
body or clothing, posing a strangulation risk.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the dresser.
Suitable for use with a flat changing mat up to 76 x 47 cm which does not compromise the eective
height of the changer barriers.
The changing area is suitable for use up to 12 months old or 11kg in weight.
Do not use the dresser if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.