EAST COAST Coast User guide

Assembly and care
instructions
Coast
Wardrobe

IMPORTANT
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully
before use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and Cross-point screwdriver
1
Hardware
Hexagon Key x 1
A x 40 B x 40 C x 8 D x 2
E x 6 F x 2 G x 36 (15mm) H x 8 (45mm)
I x 4 J x 40 K x 2

2
Wardrobe Parts
Rear leg
(L & R)
Rear top
crossbar
Wardrobe
top
Front leg
(L & R)
Rear bottom
crossbar
Wardrobe
door (L & R)
Front bottom
crossbar
Wardrobe
base
Hanging rail
(2)
Wardrobe
topper
Side panel
(L & R)
Back panel
joiner strip
Back
panel (2)

Assembly 1
Assembly 2
Left side
panel
J x 4
B x 2
B x 2
Left side
panel
NOTE:
Ensure that the holes (circled above)
are at the front of the wardrobe on the
Wardrobe top and base.
NOTE:
Repeat attachment of part B to the
Right side panel.
FRONT
Wardrobe
top
Wardrobe
base
3
A x 2
A x 2

J x 4
Assembly 3
Assembly 4
4
A x 2
A x 2
Left side
panel
Right side
panel
Wardrobe
top
Wardrobe
base

Assembly 5
Assembly 6
5
J x 8
J x 8
H x 2
C x 2
Rear and
front
crossbars
Wardrobe
topper
Rear top
crossbar
Rear bottom
crossbar
Right rear
leg

Assembly 7
Assembly 8
6
H x 2
C x 2
B x 8
B x 8
Back panel
joiner strip
Right rear
leg
Left
rear leg
Rear
assembly
NOTE:
You will need to flip the Rear assembly over
to carry out this step.

Assembly 9
Assembly 10
7
J x 8
A x 8 NOTE:
Repeat cam nut process for the Right
side panel and the Wardrobe top.
NOTE:
Repeat process for the front of the
wardrobe.
FRONT
Rear
assembly

Assembly 11
Assembly 12
8
H x 4
C x 4
B x 8
B x 8
Front
assembly
Wardrobe
topper
Front Leg
(Right)
Front bottom
crossbar
Front Leg
(Left)

9
Assembly 13
Assembly 14
A x 8
E x 1
NOTE:
Repeat cam nut process for the Right
side panel and the Wardrobe top.
NOTE:
Repeat for Right door.
G x 2
Front
assembly
Left wardrobe
door

10
Assembly 15
NOTE:
Once the wardrobe is in position, use the screws on
the hinges to adjust the fit of the doors.
Repeat for Right door.
G x 2
G x 2
Door
Left wardrobe
door assembly

K x 1
D x 1
Assembly 16
Assembly 17
NOTE:
Repeat for Right door.
Hanging
rail x2
11
F x 2
I x 4

Screw (Short) Screw (Long)Washer x 2
Plastic wall plug
(For brick and masonary wall use
only).
Fabric strap
The furniture is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place wardrobe against the wall where it is to be fitted. Mark the wall 25mm (1”) down from the top
of the wardrobe.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked
position.
3. Attach the fabric strap to the top of the wardrobe using the 15mm screw and the washer.
Before use, ensure that the strap is securely fixed to both the wall and the wardrobe.
1. 2. 3.
Assembly 18
WARNING!
IN ORDER TO PREVENT OVERTURNING, THIS PRODUCT MUST BE USED WITH THE WALL ATTACHMENT
DEVICE PROVIDED.
Serious or fatal crushing injuries can occur from furniture tipping over. To help prevent topple over,
please observe the following:
1. Use the wall attachment device provided.
2. Never allow children to climb or hang on drawers, doors or shelves.
3. Place heaviest items in the lower drawers or shelves.
4. Unless specifically designed to accommodate, do not set TV’s or other heavy objects on top of this
product.
5. Never open more than one drawer at a time.
An attachment device is provided with your product; however, you will need to source suitable fixings
for your wall type. If in doubt, please consult a qualified tradesperson.
Always ensure the wall to be drilled is free from hidden electrical wires, water and gas pipes.
Furniture stability
12

Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened
as necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the wardrobe.
Do not use if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
Only use the wardrobe on a stable and level surface.
Ensure that the wall strap is used to securely attach the wardrobe to the wall to prevent tipping.
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
8580
05_17