EAST COAST Montreal User guide

Montreal
Dresser
Assembly and care
instructions

A x 36
B x 2
C x 2
D x 27
E x 6
G x 11
(30mm)
H x 15
(45mm)
I x 6
(60mm)
K x 28
Hexagon Key x 1
J x 6
F x 12
IMPORTANT
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Hardware
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist (Pages 2 & 3). Don’t throw
away any packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
2

Changer Side x 2
Changer Back
Changer Front
Top Panel
Lower rear Crossbar
Upper Rear Crossbar
Upper Front Crossbar
Plain Crossbar x 3
Side Panel x 2
Base
Drawer Side
(L&R) x 3
Drawer Front x 3
Drawer Base x 3
Drawer Back x 3
Back Panel x 2
Drawer Brace x 3
Wooden Parts
3

A x 24
All Crossbars
A x 2
Side Panel
NOTE: Take care to insert the dowels into
the correct holes as indicated. Repeat
for the opposite end of each crossbar.
(Total 24 dowels)
Repeat for the opposite panel. (Total
4 dowels)
Assembly 1
4
Assembly 2
4

H x 15
(45mm)
H
F
H x 2
Plain Crossbar x 3
Upper Front Crossbar
Upper Rear Crossbar
Lower Rear Crossbar
I x 3
Base
Assembly 3
Assembly 4
5

G x 5
H
Top Panel
H x 6
F x 6
I x 3
Assembly 5
Assembly 6
6

NOTE: Slot to top
Back Panel
Back Panel
K x 28
Drawer Front
Drawer Side (R)
Drawer Side (L)
Drawer Back
Drawer Base
Drawer Brace
D x 9
Repeat for other 2 drawers
Assembly 7
Assembly 8
7

Changer Back
Changer Front
Changer Side (x 2)
B (each end)
A x 2 (each
end)
A x 2
E x 2
Handle
Assembly 9
Assembly 10
8

G x 2
G x 2
NOTE:
Insert Cam Nut (Part C) with
arrowed slot facing the Changer
Front.
To lock Changer Front in place,
turn Cam nuts (part C) 1/2 turn
clockwise with a large flat-bladed
screwdriver after assembly.
G x 2
C x 2
Changer Front
Changer Side
Changer Back
Changer
Side
Assembly 11
Assembly 12
9

The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place dresser against the wall where it is to be fitted. Mark the wall 25mm (1”) down from the top
surface of the changer.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked
position.
3. Remove the top drawer and thread the free end of the strap through the slot in the back panel.
4. From the inside of the dresser, attach the fabric strap to the dresser frame using the 15mm screw and
the washer.
Refit the top drawer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1
234
The type of wall fixing you will require depends on the construction of the wall. See below for details.
If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away
the core structure.
Brick or masonry: Use
the wall plug, provided
you are sure that your
wall is sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
Washer x 2
Fabric strap
Plastic wall plug
(For brick or masonry wall use only)
Screw (25mm)Screw (15mm)
Assembly 13
10

6898_V3
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Warning: Do not leave your child unattended.
Ensure that all fittings are tightened properly. Loose screws could allow a child to trap a part of their
body or clothing, posing a strangulation risk.
Ensure that the wall strap is used to securely attach the dresser to the wall to prevent tipping.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the dresser.
Suitable for use with a flat changing mat up to 75 x 47 cm which does not compromise the eective
height of the changer barriers.
The changing area is suitable for use up to 12 months or 11kg in weight.
Do not use the dresser if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.