EAST COAST Acre User guide

Assembly and care
instructions
Acre
Dresser

IMPORTANT
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully
before use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and Cross-point screwdriver
Hardware
1
Hexagon Key
x1
A x 28 (30mm) B x 16 C x 20 D x 8
F x 8 (35mm)E x 8 (25mm) G x 4 (15mm) H x 2 (30mm)
I x 4

Dresser Parts
2
Rear changer barrier
Front changer barrier
Base frame
Right side
panel
Top back
panel
Bottom
back panel
Front legs
Rear legs
Rear drawer
panel (2) Right drawer
panel (2)
Left drawer
panel (2)
Drawer support
bar (2)
Front drawer
panel (2)
Drawer base
panel (2)
Left side
panel
Dresser top panel
Dresser shelf panel

Assembly 1
Assembly 2
B x 7
A x 5
A x 4
3
Base frame
Dresser shelf
panel
Dresser top
panel
Base frame
Right side
panel
Dresser
shelf
panel
Dresser
top
panel
NOTE:
Do not tighten bolts fully until assembly is
complete.
NOTE:
Repeat process for opposite side(s).

Assembly 3
Assembly 4
4
Left side
panel
A x 5
A x 4
Front legs
Rear legs
A x 4
NOTE:
Repeat process to secure the Rear legs to
the Base frame.

Assembly 5
Assembly 6
5
Top back
panel
Bottom
back panel
NOTE:
Ensure that the slot on the Top back panel is at
the top as shown.
C x 10
C x 10
Rear changer
barrier
H x 2
(30mm)
B x 2

Assembly 7
Assembly 8
6
A x 2
Front changer
barrier
NOTE:
Repeat step for the remaining drawer.
E x 2
E x 2
Front drawer
panel
Right drawer
panel
Left drawer
panel

Assembly 9
Assembly 10
7
F x 2
F x 2
NOTE:
Repeat step for the remaining drawer.
NOTE:
Ensure slot in part D are visible.
Repeat for the remaining drawer.
D x 4
Drawer base
panel
Rear drawer
panel
Drawer
support bar

Assembly 11
8
NOTE:
Repeat step for the remaining drawer.
I x 2
G x 2
(15mm)

Screw (Short) Screw (Long)Washer x 2
Plastic wall plug
(For brick and masonry wall use
only).
Fabric strap
The furniture is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
WARNING!
IN ORDER TO PREVENT OVERTURNING, THIS PRODUCT MUST BE USED WITH THE WALL ATTACHMENT
DEVICE PROVIDED.
Serious or fatal crushing injuries can occur from furniture tipping over. To help prevent topple over,
please observe the following:
1. Use the wall attachment device provided.
2. Never allow children to climb or hang on drawers, doors or shelves.
3. Place heaviest items in the lower drawers or shelves.
4. Unless specifically designed to accommodate, do not set TV’s or other heavy objects on top of this
product.
5. Never open more than one drawer at a time.
An attachment device is provided with your product; however, you will need to source suitable fixings
for your wall type. If in doubt, please consult a qualified tradesperson.
Always ensure the wall to be drilled is free from hidden electrical wires, water and gas pipes.
1. Place the dresser against the wall where it is to be fitted and mark the wall through the slot in the
Top back panel.
2. Move the dresser away and using the long screw, washer and the appropriate wall fixing attach the
fabric strap to the marked position.
3. Replace the dresser and thread the fabric strap through the slot in the Top back panel.
4. Attach the fabric strap to the upper rear crossbar using the short screw and the washer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1. 2. 3. 4.
Furniture stability
Assembly 12
9

For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened
as necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Warning: Do not leave your child unattended.
Ensure that all fittings are tightened properly. Loose screws could allow a child to trap a part of their
body or clothing, posing a strangulation risk.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the dresser.
Suitable for use with a flat changing mat up to 78 x 48 cm which does not compromise the eective
height of the changer barriers.
The changing area is suitable for use up to 12 months old or 11kg in weight.
Do not use the dresser if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
8583
06_17