EAST COAST Alby User guide

Alby Dresser
Assembly and care
instructions

IMPORTANT!
READ CAREFULLY AND KEEP FOR
FUTURE REFERENCE
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
1
Hardware
B x 26A x 16 C x 14
(15mm)
D x 20
H x 12
E x 14
J x 6
F x 5
G x 12
(12mm)
I x 6
Hexagon Key

2
Wooden Parts
Sides (L + R)
To p
Panel Joiner
Rear Bar
Front Bar
Changer Sides
(L + R)
Changer Back
Changer Front
Drawer Back
x 3
Drawer Sides
(L + R) x 3
Drawer Base
x 3
Drawer Front
x 3
Upper Back
Panel
Lower Back
Panel

3
Assembly 1
Assembly 2
Side (L)
B x 2
Front Bar
C x 2
A x 2
Note: Repeat for
other side (R)
With cam pin inserted, turn
cam nut clockwise to tighten.
A x 2
Rear Bar

4
Assembly 3
Assembly 4
To p
Side (R)
With cam pin inserted, turn
cam nut clockwise to tighten.
B x 6
C x 2

5
Assembly 5
Assembly 6
D x 20
C x 6
E x 2
Upper Back Panel
Lower Back Panel
Panel Joiner
With cam pin inserted, turn
cam nut clockwise to tighten.

6
Assembly 7
Assembly 8
B x 4
G x 2
Drawer Side (L)
Drawer Base
Drawer Front
Note: Repeat for
other drawer side
(R)
With cam pin inserted, turn
cam nut clockwise to tighten.

7
Assembly 9
Assembly 10
J x 2
H x 4
I x 2
E x 2
Repeat for
other side
Note: Repeat
assemblies 7 - 10 for
other drawers

8
Assembly 11
Assembly 12
B x 2
C x 4
Changer Side (R)
B x 2
A x 4
A x 4
Changer Side (L)
Changer Back
Changer Front
Changer Side (L)
Changer Side (R)

9
Assembly 13
F x 5

10
Assembly 14
The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
Washer x 2 Screw (short) Screw (long)
Plastic wall plug
(for brick and masonry wall
use only)
Fabric strap
1. Place the dresser against the wall where it is to be fitted, remove the top drawer and mark the wall
through the slot in the back.
2. Move the dresser away and using the long screw, washer and the appropriate wall fixing attach the
fabric strap to the marked position.
3. Replace the dresser and thread the fabric strap through the slot in the Back Panel.
4. Attach the fabric strap to the underside of the top using the short screw and washer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
The type of wall fixing you will require depends on the construction of the wall.
See below for details. If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away the
core structure.
Cavity wall: Special toggle wall
plugs needed. Seek expert
advice.
Brick or masonry: Use the wall
plug, provided you are sure that
your wall is sound.
1 2 4
The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place dresser against the wall where it is to be fitted. Mark the wall 25mm (1”) down from the top surface
of the changer.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked
position.
3. Remove the top drawer and thread the free end of the strap through the slot in the back panel.
4. From the inside of the dresser, attach the fabric strap to the dresser frame using the 15mm screw and the
washer.
Refit the top drawer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1
234
The type of wall fixing you will require depends on the construction of the wall. See below for details.
If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away
the core structure.
Brick or masonry: Use
the wall plug, provided
you are sure that your
wall is sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
Washer x 2
Fabric strap
Plastic wall plug
(For brick or masonry wall use only)
Screw (25mm)Screw (15mm)
9
Assembly 11
1

East Coast Nursery Ltd, Robertson House
North Walsham, Norfolk, NR28 0BX, UK
For customer care or enquiries:
Call: [phone]
Email: [e-mail]
eastcoastnursery.co.uk EC_ALDR_050819
Care and maintenance
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
In use
Warning: Do not leave your child unattended.
Ensure that all fittings are tightened properly. Loose screws could allow a child to trap part of their
body or clothing, posing a strangulation risk.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the dresser.
Suitable for use with a flat changing mat up to 76 x 47 cm which does not compromise the eective
height of the changer barriers.
The changing area is suitable for use up to 12 months old or 11kg in weight.
Do not use the dresser if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.