Eco-Smart LR1321-RGBW-5MSENSER-1024 User manual

Questions, problems, missing parts? Before returning to the
store, call EcoSmart Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-800-910-7164
HOMEDEPOT.COM/ECOSMART
Item #1009 484 659
Model #LR1321-RGBW-5M-
SENSER-1024
USE AND CARE GUIDE
16.4 ft RGBW COLOR CHANGING
RECHARGEABLE BATTERY STRIP
LIGHT WITH MOTION SENSOR

2
Table of Contents
Table Of Contents........................ 2
Safety Information ...................... 2
Warranty ..................................... 4
Pre-Installation ........................... 5
Installation ................................. 6
Operation.................................... 8
Care and Cleaning .................... 11
Safety Information
PRECAUTIONS
Read and understand this entire manual before you attempt to install or operate this
product.
□ This strip light is intended for indoor use only.
□ This strip light is not intended for commercial use.
□ Do not expose the strip light to excessive heat or moisture.
WARNING: Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment. Do not damage or crimp the cable.
Do not allow the cable to come into contact with sharp objects.
CAUTION: Do not look directly at the strip light when it is illuminated.
Eye damage could occur.
NOTICE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
□ Reorient or relocate the receiving antenna.

NOTICE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
□ this device may not cause harmful interference, and
□ this device must accept any interference received, including interference that
may cause undesired operation.
□ Increase the separation between the equipment and receiver.
□ Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
3
Safety Information (continued)
Responsible Party-U.S. Contact Information
Elecwish Inc/Add: 4225 Etiwandaavenue, Suite 1 mira loma, California 91752,
USA/Elecwish.com

4
Warranty
The manufacturer warrants this xture to be free from defects in materials and
workmanship for a period of two (2) years from date of purchase. This warranty applies
only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and
your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse,
accident, modications, alteration, neglect, or mishandling. This warranty shall not
apply to any product that is found to have been improperly installed, set-up, or used in
any way not in accordance with the instructions supplied with the product. This
warranty shall not apply to a failure of the product as a result of an accident, misuse,
abuse, negligence, alteration, faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the nish on any
portion of the product, such as surface and/or weathering, as this is considered normal
wear and tear.
Contact the Customer Service Team at 1-800-910-7164 or visit
www.HomeDepot.com/EcoSmart.

5
Pre-Installation
PACKAGE CONTENTS
A
Part Description Quantity
A
B
Strip light 1
B 1000mAh lithium rechargeable controller 1
C Iron sheet with adhesive 1
D USB charging cable 1
E Remote control 1
F Mounting Clips 6
G Screws 6
C
DE
FG

6
Installation
A
AA
1
□Ensure that the mounting location is even, clean, and dry.
□Remove the protective lm (1) from the back of the strip light (A).
□Press the strip light (A) to the mounting surface and hold in place for a few
seconds.
□(optional) Shorten the strip light (A) to the desired length by cutting along the
black lines with the scissor mark.
1
2
Prepare the strip light
Install the strip light

Installation(continued)
7
A
B
C
F
G
B
□Remove the protective lm from the back of the iron sheet(C)
□Find a proper place to mount it and press to reinforce it
□After the sheet is xed for a while, attach the controller(B) to the iron sheet(C)
with its back magnet
□Use the mounting clips(F) and screws(G) to further x the strip light
3
4
Connect the controller
Install the controller
□Connect the strip light with the controller according to the arrow indicator

8
Operation
1Remote Operation
1
3
4
7
2
5
6
8
9
CAUTION: The remote control included utilizes a 3V CR2025battery; Donot dispose of batteries
in fire as they may explode or leak. Please dispose of used batteries immediately and safely. Only
replace with the samebattery type. Examine devices and make sure the battery compartment is
correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if
compartment is not secure.
WARNING: KEEP BATTERIES OUT OF THE REACH OF CHILDREN! BATTERIES ARE NOT A TOY! If swallowed,
they can cause severe injury or death within 2 hours. In case of swallowing, call emergency
services immediately. Tell others of the risks associated with button batteries to keep kids safe.
□Aim the remote directly at the controller.
□Remove the plastic tab from the back of the handheld remote (E).
□Ensure the battery contacts are clean prior to battery installation.
□Remove batteries from equipment when not in use for an extended period to time.

6
7
8
9
Static (solid) color: white, red, green, blue
Static (solid) color toggle: red, orange, yellow, green, cyan, blue,
purple, white
Auto: All preset modes repeat automatically
1
2
3
4
5
Button Description
ON: Press to turn on the light
OFF: Press to turn off the light
Adjustable speed: Increase or decrease the 5-level speed of
dynamic mode
Adjustable brightness: Increase or decrease the 5-level light
brightness
Operation(continued)
9
Dynamic Mode Button:
* 1-color ash: red, green, blue, orange, yellow, cyan, purple.
Press switch button(7) to choose color then press mode button(3)
to achieve ash effect
* 3-color jump: red, green, blue
* 7-color jump: red, green blue, yellow, cyan. purple, white in
sequence
* 3-color smooth: red, green, blue
* 7-color fade: red, green blue, yellow, cyan. purple, white in
random sequence
Motion mode:
* Press MOTION OFF to turn off the motion mode
* Press MOON to turn on the motion mode
Light turns on in darkness only when get detected
* Press SUN to turn on the motion mode
Light turns on when get detected
Successful setting reminder: white color ash

Operation(continued)
WARNING: Do not try to replace the lithium polymer battery.
The rechargeable battery in controller is not replaceable.
2Controller Operation
10
NOTE: 1. The controller is rechargeable and detachable. Get the controller
fully charged before use it.
2. When the remote and the controller set the motion mode together, the
nal effect depends on the last command
26
7
89
1
3
4
5
10

Care and Cleaning
□To clean the light strip, use a clean, dry, or slightly damp cloth.
□Do not use any cleaners with chemicals, solvents, or harsh abrasives, as damage
to the strip light may occur.
1
2
3
4
5
6
7
8
9
Description
IR Remote
PIR Motion Receiver
Dynamic Mode Button:
* 1-color ash: red, green, blue, orange, yellow, cyan, purple. Press switch
button(4) to choose color then press dynamic button(3) to achieve ash effect
* 3-color jump: red, green, blue
* 7-color jump: red, green blue, yellow, cyan. purple, white in sequence
* 3-color smooth: red, green, blue
* 7-color fade: red, green blue, yellow, cyan. purple, white in random sequence
Adjustable Speed & Brightness:
Increase or decrease the 5-level speed of all dynamic modes and
the brightness of all static colors
Delay Time Options: Light remains on for 120s, 60s or 15s when not get detected
USB charging port
Operation(continued)
11
On/Off Button:
[Short Press] Power on and change the color (red, orange, yellow, green, cyan,
blue, purple, white)
[Long Press] Power off
Motion Sensor Mode:
[Motion Sun Mode] Light turns on when get detected
[Motion Off]
[Motion Moon Mode] Light turns on in darkness only when get detected
Strip light connection port
10 Charging indicator: red light on when charging; blue light on when fully charged

Questions, problems, missing parts? Before returning to the store,
call EcoSmart Customer Service
8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m.-6p.m., EST, Saturday
1-800-910-7164
HOMEDEPOT.COM/ECOSMART
Retain this manual for future use.